Page 2 - A. Kickback Safety Precautions for Chain Saw Users
2 R ules foR s afe o peRation A. Kickback Safety Precautions for Chain Saw Users Copyright© 2012 By Echo, Incorporated All Rights Reserved. B. Other Safety Precautions 1. Do not operate a chain saw with one hand! Serious injury to the operator, helpers, bystanders, or any com- bination of these pers...
Page 3 - Never suspend the saw on a lanyard with the engine running.; NEVER; otherwise serious property damage or personal injury may result.; ALWAYS; WARNING
3 14. Keep the handles dry, clean, and free of oil or fuel mixture. 15. Operate the chain saw only in well-ventilated areas. 16. Do not operate a chain saw in a tree unless you have been specifically trained to do so. 17. All chain saw service, other than the items listed in the Instruction Manual m...
Page 4 - This symbol means the specific action; sYMBols anD siGns; ontents; Page
4 WARNING The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided. CIRCLE AND SLASH SYMBOL This symbol means the specific action shown is prohibited. Ignoring these prohibitions can result in s...
Page 5 - Chain oil fill; STOP; SYMBOL FORM
5 Carburetor adjustment - Idle speed Carburetor adjustment - High speed mixture Carefully read the Instruction manual Wear eyes, ears and head protection Carburetor adjustment - Low speed mixture Oil and gasoline mixture Symbol form/shape Symbol description/application Symbol form/shape Symbol descr...
Page 6 - An Emission Control Label; gine modification) and, if the second to last character
6 D esCRiption The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restric- tions, guide bar and saw chain installation and other assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of...
Page 7 - Sprocket guard
7 1. Hand guard (Chain brake actuating lever) 2. Ignition/Choke Lever 3. Throttle control trigger 4. Throttle control lockout 5. Air cleaner cover 6. Pull starter 7. Front handle 8. Oil tank cap n oMenClatuRe of p aRts Cs-330t, Cs-360t 10 11 12 13 14 9. Fuel tank cap 10. Saw chain 11. Guide bar 15 1...
Page 8 - KICK GUARD® TO BAR INSTRUCTIONS; For saws with Kick Guard; rear; MOVE; IMPORTANT; RepaRation; to fully seat. Tighten guide bar nuts finger tight.
8 KICK GUARD® TO BAR INSTRUCTIONS For saws with Kick Guard ® P/N 2894901 and symmetri- cal or asymmetrical low-kick type guide bars. 1. Install bolt (A) in rear hole (B) of Kick Guard ® and through front hole (C) in guide bar. 2. IMPORTANT: Dimple in Kick Guard ® (D) must engage recess in guide bar ...
Page 9 - DANGER; Never operate saw if chain brake does not; ADjUSTMENT, CHAIN TENSION; Remove air filter cover and spark plug lead.; NOTE; Replace spark plug lead and air filter cover.
9 p o 7. Turn saw over and check brake band (O) for cor- rect position around clutch drum (P). If brake band is not in place around drum, remove clutch cover, make sure brake is released, and reinstall. DANGER Never operate saw if chain brake does not function properly, otherwise saw damage and seri...
Page 10 - uel; NOT; Handling Fuel; Mixing Instructions
10 NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage section of this manual. fuel stateMent WARNING Alternative fuels, such ...
Page 11 - peRation; CHAIN LUBRICANT; After use; NTERNATIONAL
11 o peRation IMPORTANT This saw features a combination ignition/choke switch that automatically sets the throttle speed to fast idle for quick starting. Do not squeeze trigger during cold starts until after unit has started, or fast idle and choke set- tings will be released, and engine may not sta...
Page 12 - Lay unit on a flat, clear area and keep bar and chain clear of; STARTING COLD ENGINE; Fill the chain oil tank with lubricant. Do not over fill.
12 5. Lay unit on a flat, clear area and keep bar and chain clear of all obstacles. Hold top handle with one hand, and depress throttle trigger lockout (C), but do not depress throttle trigger (D). 6. Pull starter handle (F) several times until engine starts, or first starting sound is heard. (7 pul...
Page 13 - STOPPING; RUNNING; STARTING WARM ENGINE
13 A A E D D STOPPING 1. Release throttle trigger (D) and move lever (A) rearward to STOP ( O ) position. 2. Move chain brake lever (E) fully forward to lock chain brake. NOTE If engine does not stop, move ignition/choke lever forward to choke position ( ) to stop engine. Return the unit to your aut...
Page 14 - one-man job. It is difficult at times to take care for your own; uttinG; Kickback; GENERAL
14 WARNING Read the ECHO “CHAIN SAW SAFETY MANUAL” included with your chain saw for additional cutting and safety instruc- tions. Failure to obey all instructions may result in serious or fatal injuries. In all circumstances the operation of the chain saw is a one-man job. It is difficult at times t...
Page 15 - so first decide where that is!; fellinG a tRee
15 WARNING A falling tree can seriously damage anything it may hit - a car, a house, a fence, a power line, or another tree. There are ways to make a tree fall where you want it, so first decide where that is! Before cutting, clear the area around the tree. You will need good footing while working a...
Page 16 - KiCKBaCK is DanGeRous
16 Don’t cut with the saw overhead or the bar in a vertical po- sition. If the saw should kick back you may not have good enough control to prevent possible injury. Bucking is the sawing of a log or fallen tree into smaller pieces. There are a few basic rules which apply to all bucking operations.Ke...
Page 17 - Level; = Moderate difficulty. Some specialized tools may be required.; REPOWER; Maintenance Kits and Parts to make your maintenance job easier.
17 M aintenanCe anD C aRe WARNING Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a com- plete stop before removing obstructions, clearing...
Page 19 - SPARK PLUG; COOLING SYSTEM CLEANING
19 A B C GUIDE BARS AND OIL HOLES • Follow instructions for “Guide Bar and Saw Chain – Install/Re - move”. • Clean after each use -Clean the grooves (A) of the guide bar with a small screw- driver. -Clean oil holes (B) with a wire. NOTE: Symmetrical shaped Guide Bars should be inverted each time the...
Page 20 - Starter Side; MUFFLER SPARK ARRESTOR; Exhaust Port Cleaning
20 D Starter Side 1. Remove air filter cover and remove spark plug lead. 2. Remove plastic plug in side handle mount (D), and remove side handle mounting screw. 3. Remove four starter cover screws and remove starter cover. 4. Using a stiff bristle cleaning brush (do not use a metal brush), remove de...
Page 22 - CARBURETOR ADjUSTMENT; High Altitude Operation; above; BEFORE MAKING ADjUSTMENTS:; • The correct spark plug must be clean and properly gapped.; LOW ALTITUDE ADjUSTMENT; • Turn “idle” speed adjustment screw (C) CW until the saw chain
22 CARBURETOR ADjUSTMENT Engine Break-In New engines must be operated a minimum duration of two tanks of fuel break-in before carburetor adjustments can be made. Dur- ing the break-in period your engine performance will increase and exhaust emissions will stabilize. Idle speed can be adjusted as req...
Page 23 - The following combinations may be used on CS-330T and CS-360T.; hain
23 HIGH ALTITUDE ADjUSTMENT 1. Start engine and run for several minutes to reach operating temperature. 2. Stop engine. 3. Start engine and turn the HI speed needle (A) lean (CW) until the engine runs between 13,500 and 14,500 RPM. Then turn the LO speed needle lean (B) (CW) until the engine does no...
Page 25 - RouBleshootinG; • Is the engine compression adequate?
25 t RouBleshootinG T R A H C G N I T O O H S E L B U O R T M E L B O R P E N I G N E m e l b o r P k c e h C s u t a t S e s u a C y d e m e R e n i g n E - s k n a r c / d r a h s tr a t s t' n s e o d tr a t s r o t e r u b r a c t a l e u F r o t e r u b r a c t a l e u f o N d e g g o l c r e n...
Page 26 - comply with international safety standards as follows.; mance is maintained in compliance with the Standard B175.1-2000.; oRReCt; STORAGE AFTER USE; Do not store in an enclosure where fuel fumes; CAUTION; Do not lend or rent your chain saw without the
26 The installation of a chain brake may be mandatory by law or as stipulated by insurance regulations in your area of operation. You should inquire through local government offices, your employer or your local dealer to ensure that your chain saw conforms to the required safety standard. Echo chain...
Page 27 - Do not allow the saw to tip forward in order to; INSTALLATION
27 TESTING THE BRAKE • Start the engine on a solid level surface and run at a fast idle until warm. • Hold the saw firmly by the handles and accelerate the en - gine to a fast idle. OPERATION • Set the lever in the released position before starting to cut.• If the brake is tripped by kick back react...
Page 28 - Gasoline; Model
28 t eChniCal D ata * Technical data subject to change without notice. Gasoline Use 89 Octane unleaded. Do not use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not use alternative fuels such as E-15 or E-85. Model CS-330T CS-360T Dimension L x W x H mminch Weight Power...
Page 29 - aRRantY
29 ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO'S RESPONSIBILITY ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship. Under normal use and maintenance from dat...
Page 32 - or; always; you. You can find these numbers on the engine housing. For; Replacement Operator, Safety Manuals, and Parts Catalogs
CONSUMER PRODUCT SUPPORT 1-800-673-1558 8:30 - 4:30 Mon - Fri C.S.T. ECHO, INCORPORATED 400 O AkwOOD R OAD L AkE Z uRich , iL 60047-1564 www.echo-usa.com DEALER? Call 1-800-432-ECHO 1-800-432-3246 or www.echo-usa.com s eRviCinG i nfoRMation paRts / seRial nuMBeR Genuine ECHO Parts and ECHO REPOWER™ ...
