ECHO 21560065 - Manual
ECHO 21560065 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Hold the spool, pegs toward you. Place index finger be
- Page 3 – Unidades que usan una cabeza de hilo con un eje estándar; Vea la tabla (página 7) para identificar el espárrago roscado; ÍNDICE GENERAL; – Conjunto de cabeza de hilo de nilón Echomatic con eje de montaje; PRECauCÍon; • La cuchilla de corte está afilada.; marca y modelo de recortadora.; instRucciones De caBeZal; PRecaucÍon; • La cuchilla de corte está afilada
- Page 5 – instRuctions De la tÊte; marque et le modèle du taille-bordures.; requis pour la marque et le modèle du taille-bordures.; Appareils utilisant une tête de coupe à arbre standard de 10; du trou. Retirer la bobine du tambour.; remplacement; Ligne de coupe nylon ECHO de 0,095 po de 6; l’outil de; Appareils nécessitant un goujon fileté pour le montage de la tête; attention
21560065
nylon
line
head
instructions
contents
1 - High Capacity Manual Trimmer Head
w/Standard 10 mm x 1.25 Mounting Arbor
1 - 7 mm x 1.00 X 10 mm x 1.25 Mounting Stud (Bronze)
1 - 8 mm x 1.25 X 10 mm x 1.25 Mounting Stud (Silver)
1 - 10 mm x 1.25 X 10 mm x 1.25 Mounting Stud (Black)
1 - Husqvarna Line Head Arbor (Smooth - 15 mm dia.
recess & 10 mm x 1.25 Threaded hole.)
1 - Stihl Line Head Arbor (2 Notches - 12 mm dia. recess
&10 mm x 1.0 Threaded hole.)
installation
caution
Wear Gloves or personal injury may result:
• Cutoff knife is sharp.
• Gearcase and surrounding area may be hot.
1. Remove existing cutting attachment from unit
following manufacturer’s instructions.
iMPoRtant:
Remove old trimmer head adapters from power
output shaft before installing new line head.
DO NOT remove upper adapter plate from gearcase.
2. See fit-up chart (page 7) to identify threaded stud and mounting
arbor required for your brand and model trimmer.
3. Install new line head on unit:
Units requiring threaded stud to mount line head (7,8,10 mm):
1. Lock gearcase power output shaft according to trimmer manufacturer’s instructions.
2. Using color code, select threaded stud listed on fit-up chart for your brand and model
trimmer.
3. Thread small end of threaded stud into gearcase output shaft by turning counterclockwise.
4. Thread line head onto threaded mounting stud, turning counterclockwise. Hand tighten.
5. Remove locking tool from gearcase.
Units that use line head with standard 10mm arbor (STD):
1. Lock gearcase power output shaft according to trimmer manufacturer’s instructions.
2. Thread line head onto power output shaft, turning counterclockwise. Hand tighten.
3. Remove locking tool from gearcase.
Units requiring new mounting arbor (S), (H):
1. Hold drum (A) firmly, and turn knob (B) clockwise. Remove knob and spring (C).
2. Pull spool (D) from drum (A).
3. Remove old mounting arbor (E).
4. Select and install new arbor (F) listed in fit-up chart for your brand and model
trimmer.
5. Install spool in drum as shown in line loading instructions.
6. Place spring (C) over mounting shaft, and secure spool with knob (B). Turn knob
counterclockwise to tighten.
7. Lock gear case power output shaft according to manufacturer’s instructions.
8. Thread line head onto power output shaft, turning counterclockwise. Hand tighten.
9. Remove locking tool from gear case.
99922201518
06/13
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 to advance line 1. Shut engine off, and disconnect spark plug wire. Lay unit on ground with trimmer head assembly up. 2. Hold drum and turn knob clockwise several turns to allow spool to disengage pegs from drum. 3. Pull out on spool and rotate counterclockwise to feed addi- tional trimmer line th...
3 1 - Cabeza de Corte Manual de Repuesto estándar de 10 mm x 1,25 1 - Perno de montaje (bronce) de 7 mm x 1,00 X 10 mm x 1,25 1 - Perno de montaje (plateado) de 8 mm x 1,25 X 10 mm x 1,25 1 - Perno de montaje (negro) de 10 mm x 1,25 X 10 mm x 1,25 1 - Eje de cabeza de hilo Husqvarna ( Liso - 15 mm d...
5 instRuctions De la tÊte De couPe À liGne nYloncontenu 1 - Tête de coupe Manuelle de Recharge standard 10 mm x 1,25 1 - Goujon de montage 7 mm x 1,00 X 10 mm x 1,25 (bronze) 1 - Goujon de montage 8 mm x 1,25 X 10 mm x 1,25 (argent) 1 - Goujon de montage 10 mm x 1,25 X 10 mm x 1,25 (noir) 1 - Arbre ...
