Page 3 - Table of Contents
i Table of Contents Section 1: Read Me First! ............................................................... 1 Capabilities and Specifications: ......................................................... 2How GPS Works ................................................................................. ...
Page 4 - ii
ii Navigate a Trail ............................................................................ 47Navigate a Back Trail ................................................................... 49 Transfer Custom Maps and GPS Data Files ................................... 50Cancel Navigation ...............
Page 6 - iv; CAUTION
iv Find Interstate Highway Exits ...................................................... 103Find Map Places or Points of Interest (POI) ................................. 105Find Streets or Intersections ......................................................... 107 Find a Street .........................
Page 7 - How this manual can get you out on the road, fast!; 42c iGPS and begin installing it, please give us a moment
1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of digital GPS! We know you're anxiousto begin navigating, but we have a favor to ask. Before you grab theIntelliMap ® 642c iGPS and begin installing it, please give us a moment or two to exp...
Page 8 - Capabilities and Specifications:; General
2 After you've learned the basics (or if you already have some GPS expe-rience), you may want to try out some of the IntelliMap 642c's manyadvanced navigation features. That brings us to Section 4, Advanced GPS Operations . This section contains the rest of the unit's GPS com- mand functions, organi...
Page 9 - GPS
3 Case size: ......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6 cm); sealed and waterproof; suitable forsaltwater use. MMC slots: ...................... One with waterproof door (SD card compatible). Recording: ........................ MMC & SD cards for recording ...
Page 10 - Extended storage in temperatures higher or lower than; How GPS Works; Installation & Accessories
4 NOTE: The above memory capacities refer only to the IntelliMap 642c's on-board memory. The amount of GPS data you can record and save forrecall later is limited only by the number and size of MMC cards youhave. NOTICE! The storage temperature range for your IntelliMap 642c is from -4degrees to +16...
Page 12 - Introduction to GPS and WAAS; on page; A minimum of three satellites are required to determine a 2D fix.
6 Introduction to GPS and WAAS Well, now you know the basics of how the unit does its work. You mightbe ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your IntelliMap 642c and plug in the power. Oryou might want to see how our text formatting makes the...
Page 14 - How to use this manual: typographical conventions; Arrow Keys; . These indicate that; to; You are asked to wait while it converts the trail into a route.
8 Remember that this receiver is only a tool. Always have anothermethod of navigation available, such as a map or chart and a compass. Also remember that this unit will always show navigation informationin the shortest line from your present position to a waypoint, regardlessof terrain! It only calc...
Page 16 - Notes
Page 17 - Preparations; Install the power cable and route it to the GPS unit.; Power Connections
11 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, butwe recommend this installation sequence: Caution: You should read over this entire installation section before drill-ing any holes in your vehicle or vessel! 1. Determine th...
Page 18 - as close to the power source as possible.; Power connections for the IntelliMap 642c GPS unit.; This product
12 This may result in corrosion of the plug body along with the electri-cal contacts in the cable and the unit's power socket. In saltwater environments we recommend you connect the powercable to the auxiliary power switch included in most boat designs.If that results in electrical interference, or ...
Page 20 - NMEA Cable Connections; NMEA Wiring; Com-1 wiring to receive NMEA position information; Mounting the Unit: Bracket or Portable; bracket mounting system. This converts the unit's gimbal bracket
14 NMEA Cable Connections NMEA is a standard communications format for marine electronicequipment. For example, an autopilot can connect to the NMEA inter-face on the IntelliMap 642c and receive positioning information. TheIntelliMap 642c can exchange information with any device that trans-mits or r...
Page 21 - Install the gimbal bracket. Orient the bracket so the arms slope; Front
15 mation is on the inside back cover of this manual. For a complete look atthe many mounting options, visit the RAM web site at www.ram-mount.com. Optional R-A-M mounting system. Bracket Installation Mount the IntelliMap 642c in any convenient location, provided there isclearance behind the unit wh...
Page 22 - IntelliMap 642c when mounted on gimbal bracket.; Portable Installation
16 Some customers, however, prefer to mount the bracket to the side of thecable hole — it's a matter of personal preference. Front view (left) and side view (right) showing dimensions of the IntelliMap 642c when mounted on gimbal bracket. After drilling the hole, pass the power cable's bare-wire end...
Page 23 - Installing batteries in a typical portal power pack.; MMC or SD Card Memory Card Installation; or
17 pack expands the uses for your GPS unit. The PPP makes it easy totransfer your unit from a boat to a car, recreational vehicle, airplane orother vehicle without drilling and mounting a second bracket. You canuse your unit in your own car or boat, then take it along when riding ina friend's vehicl...
Page 24 - Memory card compartment with a 16 MB MMC card installed.; To remove an MMC; Other Accessories; this way
18 Additional MMC cards are available from LEI Extras; see ordering in-formation inside the back cover of this manual. MMCs and SD cardsare also available at many camera and consumer electronics stores. The MMC slot is located in a compartment on the front of the case. Thecompartment door is located...
Page 27 - Section 3: Basic GPS Operations; most; Keyboard; IntelliMap 642c GPS unit view showing the Map Page.; PAGES
21 Section 3: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 4 is arranged in alphabetic...
Page 28 - Power/lights on and off; Page; Main Menu; System Setup and GPS Setup Options
22 4. ARROW KEYS – These keys are used to navigate through menus, make menu selections and move around the map. 5. ENT/ICONS – The Enter key allows you to save data, accept values and execute menu commands. It is also used to create event markericons. 6. EXIT – The Exit key lets you return to the pr...
Page 30 - Pages; Pages Menu showing some Map display options.; Satellite Status Page; EXIT
24 Pages The unit has three Page displays: Satellite Status Page, NavigationPage and Map Page. They are accessed by pressing the PAGES key, then using ← → to select a Page. (Clear the Pages Menu by pressing EXIT .) Pages Menu showing some Map display options. Satellite Status Page The Satellite Stat...
Page 32 - The navigation screen looks like the one below when you're; Traveling north and recording a trail on the Navigation page. The
26 The Satellite Status Page has its own menu, which is used for settingvarious options. (Options and setup are discussed in Sec. 5). To accessthe Satellite Status Page Menu, from the Status Page, press MENU . Navigation Page This screen has a compass rose that not only shows your direction oftravel...
Page 33 - Navigation Page going to a waypoint while creating a new trail.; Red course line
27 Speed (ground speed) is the velocity you are making over the ground. (Ifyou wish, you can customize the Speed data box to display ClosingSpeed instead. Closing Speed is also known as velocity made good. It'sthe speed that you're making toward the waypoint. For instructions,see the Customize Page ...
Page 35 - additional; Map Pages with high-detail MapCreate map of urban area loaded on
29 The Zoom In and Zoom Out keys zoom the map to enlarge or reduce itscoverage area and the amount of mapping detail shown. There are 40available map zoom ranges, from 0.02 miles to 4,000 miles. Map Page opening screen (left). Map page zoomed to 100 miles (cen- ter). Map zoomed to 10 miles (right). ...
Page 36 - Background map vs. MapCreate map content
30 Background map vs. MapCreate map content The background map includes: low-detail maps of the whole world (con-taining cities, major lakes, major rivers, political boundaries); and me-dium-detail maps of the United States. The medium-detail U.S. maps contain: all incorporated cities; shadedmetropo...
Page 37 - box works on POIs at any zoom range.; display
31 When the map is zoomed out far enough, most POIs appear as squaredots (left). As you zoom in closer, the symbols become readable icons. In the 0.2-mile zoom example (right), the cursor has selected the Cupps Café POI, which triggers a pop-up box with the POI name. This pop-up box works on POIs at...
Page 38 - Two Position Formats map page option.; ENT
32 Two Position Formats map page option. In pages that have two major windows (such as two maps) you can tog-gle back and forth between the two windows by pressing PAGES | PAGES . Each time you switch between the windows, Active Map will be displayed at the top of the active window. Pages Menu with ...
Page 39 - Fig. 1. Two Maps page display with four flashing arrows on the divid-; or by contacting customer service.
33 Press an arrow key parallel to the centerline to switch between hori-zontal and vertical layout. Press EXIT to clear the four flashing arrows. Fig. 1. Two Maps page display with four flashing arrows on the divid- ing centerline. Fig. 2. The centerline has been moved down to enlarge the top map, w...
Page 40 - Basic GPS Quick Reference; Page Name
34 Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, trynavigating to a location at least a few blocks away. While you're learning,navigation in too small an area will constantly trigger arrival alarms. 1. Connect the unit to electric power and the antenna...
Page 41 - Find Your Current Position; Moving Around the Map: Zoom & Cursor Arrow Keys; ZIN
35 Find Your Current Position Finding your current position is as simple as turning on the unit. Un-der clear sky conditions, the unit automatically searches for satellitesand calculates its position in approximately one minute or less. NOTE: Clear sky conditions means open sky, unobstructed by terr...
Page 42 - Selecting Any Map Item With the Cursor; Searching; In this example, we will look for the
36 The selected wreck (the Empress) to the southeast is 12.81 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map andfind the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob-ject. On most ...
Page 44 - Finding Waypoint screen showing; To clear the search and return to the last page displayed, press; Set a Waypoint
38 5. The POI information screen appears. (This is how you can use thisunit as a business phone directory!) If you wanted to navigate there,you could by pressing Enter. The Go To waypoint command is alreadyhighlighted. But we just want to see it on the map, so press ↓ to F IND O N M AP | ENT . 6. Th...
Page 47 - Navigate To a Waypoint; Navigating to waypoint 002 and leaving a trail.
41 4. Press ↓ to L ONGITUDE | ENT . Enter the longitude by pressing ↑ ↓ to change the first character, then press → to the next character and repeat until the longitude is correct. Press ENT , then EXIT | EXIT to return to the previous page display. The waypoint is saved and automatically given anam...
Page 48 - and; Navigate Back to MOB Waypoint; Navigating to Man Overboard: Man Overboard activated message; To cancel navigation to MOB, press
42 Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or familymember fall overboard. This unit has a man overboard feature thatshows navigation data to the location where the feature was activated.To activate it, press the ZOUT and ZIN keys at the same time....
Page 49 - Navigate to Cursor Position on Map; The; command navigates to the current cursor position on; The cursor crosshairs are centered on Oologah, Oklahoma.; MENU
43 Navigate to Cursor Position on Map The G O T O C URSOR command navigates to the current cursor position on the map. It is a quick way to navigate to anything you can see on themap display. 1. Use the cursor with the zoom in and zoom out keys to move aroundthe map until you find a location you wan...
Page 50 - show navigation information.; Navigate to a Point of Interest; Creating and Saving a Trail
44 The 60-mile zoom figure (left) shows the red course line connecting the current position to the destination. The Navigation Page (right) will also show navigation information. To stop navigating to the cursor, use the Cancel Navigation command.Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ...
Page 51 - Sequence for saving a trail and beginning a new one. My Trails com-; Active Trail Name
45 The unit is set to automatically create and record a trail when it isturned on. The unit will continue recording the trail until the lengthreaches the maximum trail point setting. The default is 2,000 points,but the unit can record trails 9,999 points long. When the point limit isreached, the uni...
Page 52 - Displaying a Saved Trail; To turn off trail display:; Trail Name; Navigating Trails
46 Tip: Another quick way to stop recording one trail and begin a new oneis to use the New Trail command. Press MENU | MENU | ↓ to M Y T RAILS | ENT | ENT . Caution: You also have the option of completely turning off trail record-ing, under the trail Options command. If, however, the UpdateActive Tr...
Page 54 - verted to a route when you navigate the trail.
48 Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate Route command highlighted for Trail 2. A trail is always con- verted to a route when you navigate the trail. On the Map Page, the trail you are navigating...
Page 55 - north straight toward trail point 3 (left). Bearing arrow shows the; Navigate a Back Trail
49 Navigate trail: Driver is heading southeast straight toward trail point 3 (left). Driver has reached point 3 and has turned southwest to follow the trail (right). Navigate trail, navigation page (compass rose) views: Driver is heading north straight toward trail point 3 (left). Bearing arrow show...
Page 56 - Transfer Custom Maps and GPS Data Files; You must enter which way you want to transfer data, from an MMC
50 NOTE: If you are already located at or near the end of your trail, the arri-val alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and let your unit guide you. 6. When you reach your destination, be sure to cancel your navigation.Press...
Page 57 - These figures (from left to right) show the menu sequence for naming
51 1. Insert the MMC into your unit. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to T RANSFER M Y D ATA | ENT . 2. The Transfer My Data menu includes a message which tells you if anMMC is present or not. If no MMC is present, you must insert a cardinto the unit to activate the Load or Save com...
Page 58 - These figures show the menu sequence for loading a GPS Data File; Cancel Navigation
52 These figures show the menu sequence for loading a GPS Data File from an MMC into the unit's memory. Cancel Navigation You can turn off any of the navigation commands after you reach yourdestination or at any other time by using the Cancel Navigation com-mand. Press MENU | MENU | ↓ to C ANCEL N A...
Page 59 - Advanced GPS Operations; Find Distance Current Position to Another Location; Find Distance From Point to Point; current
53 Section 4: Advanced GPS Operations Find Distance Current Position to Another Location 1. While on the Map Page press MENU | ↓ to F IND D ISTANCE | ENT . 2. Center the cursor crosshairs on the position you want to find the dis-tance to. A rubber band line appears, connecting your current positiont...
Page 60 - Icons; can
54 Icons Icons are graphic symbols used to mark some location, personal point ofinterest or event. They can be placed on the map screen, saved and re-called later for navigation purposes. These are sometimes referred to asevent marker icons. This unit has 42 different symbols to choose fromwhen crea...
Page 61 - Navigate to an Icon; Routes
55 Delete icons menu. 1. Press MENU | ↓ to D ELETE M Y I CONS | ENT . 2. Press ↓ to D ELETE A LL I CONS , D ELETE B Y S YMBOL or D ELETE F ROM M AP and press ENT . 3. The Delete All Icons confirmation message will appear. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by ...
Page 63 - with Add From Map command selected.; line will become the course for the route.
57 Edit Route menu (left). Edit Route Waypoints menu (right) with Add From Map command selected. 2. Press ↑ to N EW R OUTE , then press ENT . (To add to an existing route, press ↓ ↑ to route name | ENT .) 3. Press ↓ to E ND OF R OUTE | ENT | ↓ to A DD F ROM M AP | ENT . The Map Page appears with the...
Page 64 - Delete a Route
58 Route creation sequence, continued: Fig. 4. Point (3) set at channel mouth. Fig. 5. Waypoint (4) set further south along the beach, at a rec- ognizable landmark (Bob Hall Pier). Waypoint PLFM Q W ends the route at an oil platform some distance from the shore. Fig. 6. Press EXIT to save the route ...
Page 65 - Edit Route Waypoints menu.; Navigate a Route
59 Edit a Route Name 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Highlight Saved Route Name | ENT | ↑ to Name | ENT . 3. Press ↑ ↓ to change the first character, then press → to move to the next character and repeat unt...
Page 66 - Edit Route menu (right) with Navigate Route command selected.; to select; and press; gered and the bearing arrow on the compass rose has turned to point
60 Route Planning command on Main Menu (left). Routes menu (center). Edit Route menu (right) with Navigate Route command selected. 2. Press ↓ to select saved route name | ENT . Highlight N AVIGATE and press ENT . 3. Upon arrival at your destination, cancel navigation.Press MENU | MENU | ↓ to C ANCEL...
Page 67 - Navigate a Route in Reverse; you to navigate the route from the end to the beginning.
61 In Fig. 3 the traveler has turned northeast on his new course and is heading straight for Wpt 2, which is 0.20 miles away. Fig. 4 shows route navigation on the Map Page. In this figure, the traveler has reached Wpt 2 and is starting on the leg between Wpts 2 and 3. Navigate a Route in Reverse Her...
Page 68 - Trails; Delete a Trail; Trail selected with map cursor (left). The box at the bottom of the; Edit a Trail Color
62 Trails Delete a Trail This is the command used to erase or delete a trail.Press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | → to D ELETE T RAIL | ENT | ← to Y ES | ENT . To Delete all trails at once : 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press → to D ELETE A LL | ...
Page 69 - Utilities; Alarm Clock
63 Edit a Trail Pattern To edit a trail pattern press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | ↓ to P ATTERN | ENT . Press ↑ ↓ to change the first character, then press → to the next character and repeat until the pattern is cor- rect. Press ENT . To get back to the main page p...
Page 70 - Waypoints; Name
64 Waypoints Delete a Waypoint To delete a waypoint from the waypoint list press WPT | ↑ to M Y W AYPOINTS | ENT | ↓ to Name | ENT . Press ↑ ↓ to select the desired charac- ter then press → to choose the next character. After the desired way- point is highlighted in the list, press ENT | ENT . Use ↓...
Page 73 - System & GPS Setup Options; Alarms; To change alarm settings:
67 Section 5: System & GPS Setup Options Alarms This unit has three GPS alarms: Arrival Alarm, Off Course Alarm andAnchor Alarm — the only one of the three set to Off by default. You can set an arrival alarm to flash a warning message and sound atone when you cross a preset distance from a waypo...
Page 74 - IMPORTANT ALARM NOTES:; Check MMC Files and Storage Space; To set Com Port Configuration:
68 satisfied with the distance setting. If you want to enable the otheralarms, repeat steps 2 and 3. 4. Press EXIT repeatedly to get back to the main page display. IMPORTANT ALARM NOTES: Anchor Alarm - The anchor alarm may be triggered even when youare sitting still. This usually happens when using ...
Page 75 - Menus for changing Com Port settings.; Configure NMEA
69 Menus for changing Com Port settings. For assistance in configuring the unit to communicate with anotherdevice, consult the factory. Customer service phone numbers are in theback of this manual. Also see the entry below for Configure NMEA . Configure NMEA You can configure the unit to use specifi...
Page 76 - Coordinate System Selection; Menus used for changing coordinate system.
70 • VLW transmits the distance traveled through water as meas-ured by the paddle wheel. • VHW transmits the water speed as measured by the paddlewheel. 4. When the desired prefixes are turned on, press EXIT repeatedly to get back to the main page display. Coordinate System Selection The Coordinate ...
Page 77 - Configure Loran TD menu.; Customize Page Displays; To change the information displayed in a data box:
71 The Military Grid Reference System (MGRS) uses two grid letteringschemes, referred to as standard and standard + 10 MGRS on this unit.Your position and datum in use determines which one to use. If you usestandard and your position is off significantly, then try the alternate. NOTE: When the posit...
Page 78 - GPS Simulator; To get to the GPS Simulator:
72 The Data Viewer menu has four categories: GPS Data, Navigation, TripCalculator and Time. Each category has its own data option menu. Ground Speed flashing on Two Position Map page (left). Data Viewer menu with no open categories (center). GPS data category opened with Ground Speed selected (right...
Page 79 - eler is following a track of 144o at a speed of 71 miles per hour.; Simulating Trail or Route Navigation
73 GPS Setup Menu (left). GPS Simulator menu (center). Map Page showing Steer with Arrows dialog boxes (right). The trav- eler is following a track of 144º at a speed of 71 miles per hour. Choose the desired settings, then turn on the simulator by highlightingthe GPS S IMULATOR O N box and pressing ...
Page 80 - Initialize GPS; . When the message automatically clears, follow; Map Auto Zoom; To turn this feature on from the; Map Data
74 Tip: You can pick any spot on the map to begin a simulation by usingthe Initialize GPS command. It allows you to move the position ar-row to any location on the map. The command is detailed below. Initialize GPS In simulator mode, the Initialize GPS command makes the unit operateas if it is sitti...
Page 82 - Map Datum Selection
76 in diameter (same as the zoom range). The second smaller ring is 50miles in diameter (always 1/2 the zoom range). The distance from your current position to the smaller ring (the ring'sradius) is 25 miles (always 1/4 the zoom range). With the map cursor,you can scroll over to see the third and fo...
Page 83 - Map Detail Category Drawn; To get to Map Categories Drawn:; Map Fix
77 GPS Setup Menu (left). Map Datum Menu (right). Map Detail Category Drawn This menu determines what mapping features are shown on the screen.This includes, waypoints, trails, icons, cities and highways, etc. You canturn on or off any of these items, customizing the map to your needs. Map Menu (lef...
Page 84 - To configure a map fix:; Configure a map fix so the unit can find your position
78 on the map. It then shows the present position as distance on the mapfrom that reference point. For example, if it shows a distance of UP 4.00" and LEFT 0.50", youthen measure up four inches and to the left a half-inch from the refer-ence point on the map to find your location. To configu...
Page 85 - Map Orientation
79 Press → to S ELECT O RIGIN | ENT to bring up the waypoint and POI list. Select the waypoint (or a landmark of POI) you saved the referencepoint under and press ENT | ENT . Spell out the name of the waypoint, landmark or POI in the Find By Name box or press ENT to select the item from the list bel...
Page 86 - NauticPath; Nautical Chart Notes; NauticPath chart showing Chart Note icon selected by cursor (left).
80 To change map orientation from the Map Page, press MENU | ↓ to M AP O RIENTATION | ENT . Use ↑ ↓ to select the desired mode, then press ENT . Press EXIT | EXIT to return to the page display. Map Menu (left). Map Orientation menu with the North Up selected (right). NOTE: In North Up and Course Up,...
Page 89 - Current Information screen.; Slack Water Line
83 NauticPath chart showing Tidal Current Station icon selected by cur- sor (left). Icon animates automatically at .08-mile zoom range (right). Current Information screen. The Tidal Current Information screen displays daily tidal current datafor this station on this date at the present time. The gra...
Page 90 - as shown by the down arrow at the top of the icon.; To view tide information:
84 To select another date: 1. Use ← → to highlight month, day or year, then press ENT . 2. Use ↑ ↓ to select the desired month, day or year and press ENT . To clear the information screen, press EXIT . Tide Information NauticPath charts contain Tidal Information,represented at large zoom ranges by a...
Page 91 - Tide Information screen.; range; Navionics; To display a Navionics chart:
85 Tide Information screen. The Tide Information screen displays daily tidal data for this station onthis date at the present time. The graph at the top of the screen is anapproximate view of the tidal range pattern for the day, from midnight(MN) to noon (NN) to midnight (MN). The dotted line across...
Page 92 - Map Name; Overlay Data; with GPS Data category opened (center). Ground Speed is turned on; To overlay information on your screen:
86 2. From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to M AP C HOICE | ENT . Select the Map Name , then press ENT | EXIT | EXIT . WARNING: You should never format the MMC containing yourNavionics chart. Formatting the MMC will permanentlyerase the chart from the card. Overlay Data On any ...
Page 93 - To remove overlaid data:; Overlay Data Shown menu with position data option selected (left).; To move overlaid data:
87 Every Page display has a maximum number of items you can show us-ing the Overlay Data command. To remove overlaid data: 1. While on the Page that shows the data you want to remove, press MENU | ↓ to O VERLAY D ATA | ENT . 2. You will see a list of the overlay data currently displayed. Select thei...
Page 94 - Map Page showing Ground Speed, Trip Time and the Steering Arrow.; To turn on Popup Help
88 To change displayed data font size: 1. From the Map page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. Press ↓ ↑ to select a data type to resize, then press ← → scroll through five data size options: Off, Small, Medium, Large and Enor-mous. Press EXIT . The selected data type will be displayed in ...
Page 95 - Reset Options; To reset unit to factory defaults:; Require WAAS
89 System Setup Menu (left) with Pop-up Help highlighted. Pop-up Help message for the Map Data (right). Reset Options To reset unit to factory defaults: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to R ESET O PTIONS | ENT | ← to Y ES | ENT . NOTE: Reset Options does not erase any waypoints,...
Page 96 - Require WAAS command on GPS Setup Menu.; Screen Contrast and Brightness; To adjust the screen's display mode
90 To Require WAAS: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to R EQUIRE WAAS | ENT . 2. To return to the main page display, press EXIT | EXIT . 3. Repeat Step 1 to turn off WAAS requirement. Require WAAS command on GPS Setup Menu. Screen Contrast and Brightness To access the Screen menu, pr...
Page 97 - Set Language; To select a different language:; Set Local Time
91 Set Language This unit's menus are available in 10 languages: English, French, Ger-man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish. To select a different language: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT . 2. Press ↓ to S ET L ANGUAGE | ENT . 3. Use ↓ ↑ to select a dif...
Page 98 - To turn off WAAS alarm:; Software Version Information; To adjust Sounds and Alarm Styles:
92 frequently lose and reacquire its lock on a WAAS satellite. That canresult in the alarm repeatedly going off. If you want, turn off the WAASAcquired/Lost alarm without affecting how the unit uses WAAS. To turn off WAAS alarm: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to S HOW WAAS A LARM ....
Page 99 - Track Smoothing; should always be; Trail Options
93 To set Volume: Press ↓ to V OLUME . Use ← → to adjust the volume. To set Alarm Style: Press ↓ to A LARM S TYLE | ENT . Press ↑ ↓ to change the style and press ENT . After the option is set, press EXIT | EXIT to re- turn to the main page display. Sounds highlighted on main menu (left). Sounds menu...
Page 101 - New Trail; Trail Visibility and Other Trail Options
95 first character, then press → to the next character and repeat until the entry is correct. Press EXIT to return to the Trail Options Menu. Update Rate setting (left) and Update Distance setting (right). Trail Name highlighted (left). Edit Trail menu (center). Trails menu with New Trail highlighte...
Page 102 - Transparency; To adjust Transparency level:
96 Transparency set to 0 percent (left) and 50 percent (right). Transparency Use the transparency menu to adjust the transparency of menu win-dows. A high transparency setting allows you to continue monitoringthe screen's display while working with a menu. A low transparencyusually will make menu te...
Page 103 - Units of Measure; To set Units of Measure:
97 Units of Measure This menu sets the speed, distance, depth, temperature and headingunits. To change the units: Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ENT . To set Units of Measure: Select a category you would like to change. Highlight the desired unit of measure option under the category...
Page 106 - Find Addresses; try is complete. Figure 3: The Find Street menu with Find By Name
100 To search somewhere else, use the arrow keys to center the cursorcrosshairs on the desired location. When the cursor is active, theunit always begins searching at the cursor location. In search results, the distance and bearing to the selected item will becalculated from the current position. In...
Page 107 - not
101 NOTE: We recommend you do not enter a city name unless the list you are given is too large when searching without it. This unit can actuallysearch quicker without a city and you save time by not entering acity name. Find City field (left). Search in particular city only option (center). Find Cit...
Page 108 - Map Page showing location of address on the map, highlighted by cur-
102 8. To navigate to the address, press MENU select G O T O and press ENT . The unit will begin showing navigation information to the address. Ifyou are only looking up an address, highlight F IND and press ENT . The map page will appear with the cursor crosshairs centered on the ad-dress. Tip: If ...
Page 109 - spell out
103 Find Any Item Selected by Map Cursor On the Map Page with a POI or map feature selected by the cursorpress WPT. To return to the main page display, press EXIT . NOTE: Since the Go To waypoint command is highlighted, you can navi-gate to the selected POI by pressing ENT | EXIT while in the POI Wa...
Page 110 - Service
104 Find By Name menu (left). Find Exit menu with exit selected (right). 3. Once you have selected a highway name you can select an exit. Press ↓ to switch to the Exit List, then press ↓ ↑ until you highlight the exit, then press ENT. 4. In the Exit Information screen you have two choices. A. Press ...
Page 111 - Find Map Places or Points of Interest (POI); WPT; Find Waypoint menu with Services POI category selected (left); Search by nearest POI.
105 Exit Information screen (left). General location and amenities information (right). Find Map Places or Points of Interest (POI) 1. Press WPT , use ↓ ↑ to select a map place or POI category, then press ENT . (To narrow your search, press → to select a subcategory before pressing ENT .) You will b...
Page 112 - Search by name of POI.
106 Find by nearest option (left) with resulting POI list (right). 3. Search by name of POI. Highlight N AME and press ENT . There are two options: A. You can spell out the POI name in the top selection box. Press ↑ ↓ to change the first letter, then press → to move the cursor to the next letter and...
Page 113 - Find Streets or Intersections; Find a Street; selection list
107 Go To POI option (left). Find on Map POI option (right). Find Streets or Intersections Find a Street 1. From the Map Page, press MENU | ↓ to F IND S TREETS | ENT and the Find Streets Menu appears. Find Streets command (left). Find Streets menu (right). 2. You must enter a street name in the Firs...
Page 114 - The Find Streets menu with the Find First Street command high-; Find an Intersection
108 The Find Streets menu with the Find First Street command high- lighted (left). Streets Found list (center). Map Page showing results of a street search (right). The cursor points to the located street. 3. The Find Streets menu reappears with the street you are searching forin the First Street bo...
Page 115 - Map Page showing results of an intersection search.
109 B. Or you can jump down to the lower box and pick the second street from the selection list. Press ENT , then press ↓ ↑ to select a street from the list and press ENT . 5. The Find Streets menu reappears with the first and second streetdialog boxes filled in. You could now use similar techniques...
Page 116 - Find Waypoints; To navigate
110 Find Waypoints 1. Press WPT | ↑ to M Y W AYPOINTS | ENT . 2. If searching for the nearest waypoint, select N EAREST and press ENT . If searching by name, highlight N AME and press ENT . (To search by name, jump to step 5.) Find By Nearest command (left). Find by Name command (center). List of th...
Page 117 - cursor crosshairs are centered on the desired waypoint (right).
111 Find By Name menu (left). Waypoint Information screen (center). The cursor crosshairs are centered on the desired waypoint (right). A. To navigate to the waypoint, press ENT . The Go To Waypoint command is already highlighted. The unit will show navigation in-formation to the waypoint. B. To fin...
Page 119 - Switzerland
113 Section 7: Supplemental Material Datums Used by This Unit WGS 1984Default AdindanMean for Ethiopia,Sudan AdindanBurkina Faso AdindanCameroon AdindanEthiopia AdindanMali AdindanSenegal AdindanSudan AfgooyeSomalia Ain el Abd 1970Bahrain Ain el Abd 1970Saudi Arabia Anna 1 Astro 1965Cocos Islands An...
Page 126 - FCC Compliance; Reorient or relocate the receiving antenna.
120 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi-cations Commission (FCC) Rules. Operation is subject to the fol-lowing two conditions: (1) this device may not cause harmful in-terference, and (2) this device must accept any interference re-ceived, including interfere...
Page 128 - DATABASES LIMITED WARRANTY
122 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Eagle Electronics, a division of LEI, the manufac-turer of this product. "You" or "your" refers to the first person who purchasesthe product as a consumer item for personal, family, or household use...
Page 129 - EAGLE ELECTRONICS
123 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufac-turer of this product. "You" or "your" refers to the first person who purchases this productas a consumer item for personal, family, o...
Page 130 - How to Obtain Service...; ...outside Canada and the USA:; To locate an Eagle dealer near
124 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert serviceand genuine Eagle replacement parts. If you're in the United Statesand you have technical, return or repair questions, please contact theFactory Customer Service Department. Before any produ...
Page 131 - Dealer Locator; Shipping Information
Accessory Ordering Informationfor all countries To order Eagle accessories such as power cables or transducers,please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumerelectronics should be able to assist...
Page 132 - LEI-Eagle
Visit our web site: www.eaglesonar.com Eagle Pub. 988-0152-161 © Copyright 2005 All Rights Reserved Printed in USA 121905 LEI-Eagle