Dynex DX-WD1335 - Manual - manualsarea.com

Page 2 - Safety information and specifications; This stand’s wood surface is; Tools needed; No. 2 Phillips screwdriver

2 DX-WD1335 Need help? Call 800-305-2204 Safety information and specifications CAUTION: This stand’s wood surface is intended only for use with a product not weighing more than 50 lbs (22.7 kg) and having a width that will permit it to sit evenly on the stand with no more than one-inch overhang on e...

Page 3 - Package contents: parts; identify similar parts.; Item

3 DX-WD1335 Need help? Call 800-305-2204 Par ts Package contents: parts Note: Some parts have a label on the edge to help distinguish similar parts from each other. Use this illustration to help identify similar parts. Item Description Qty. A Right end 1 B Left end 1 C Top 1 D Lower shelf 1 E Back 1...

Page 4 - Package contents: hardware; Label

4 DX-WD1335 Need help? Call 800-305-2204 Hardw ar e Package contents: hardware Make sure that you have all the hardware necessary to assemble your new TV stand: Label Hardware Qty. K 2 L 13 M 6 N 7 O 2 P 2 Twist-lock® fastener Hidden cam Cam dowel Cam screw Angle bracket Wood dowel Label Hardware Qt...

Page 5 - ) into each of the two the holes in the back (; fasteners in this

5 DX-WD1335 Need help? Call 800-305-2204 Assembly inst ructio ns Step 1: Caution: Assemble your TV stand on carpeted floor or on the empty carton to avoid scratching your stand or the floor. Push a Twist-lock® fastener ( K ) into each of the two the holes in the back ( E ). You’ll need: Important: D...

Page 6 - Important: Do not tighten the hidden cams in this step.

6 DX-WD1335 Need help? Call 800-305-2204 Step 2: 1 Push 13 hidden cams ( L ) into the ends ( A and B ), top ( C ), and back ( E ). Make sure that the arrows on the hidden cams (L) are pointing toward the closest edge. 2 Insert the metal end of a cam dowel ( M ) into each hidden cam, except in the to...

Page 8 - Tightening hidden cams:; In the; remaining; not completely tightened will loosen, and parts may separate.; Arrow

8 DX-WD1335 Need help? Call 800-305-2204 Tightening hidden cams: In the remaining steps, use these illustrations for instructions on tightening hidden cams. Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not completely tightened will loosen, and par...

Page 9 - Align the stop molding (; Phillips screwdriver

9 DX-WD1335 Need help? Call 800-305-2204 Step 4: Align the stop molding ( J ) with the top ( C ), then tighten the three hidden cams. You’ll need: Surf ace wit h h idd en c am s Sur face wit h h oles Phillips screwdriver

Page 10 - and; Edge with Twist-lock® fasteners

10 DX-WD1335 Need help? Call 800-305-2204 Step 5: Align the ends ( A and B ) with the back ( E ), then tighten the two hidden cams. You’ll need: Su rfa ce w ith hi dd en ca ms Surf ace wit h Tw ist-lo ck® fast ene rs Edge with Twist-lock® fasteners Edges with hidden cams Edges with hidden cams Su rf...

Page 14 - Long finished edge

14 DX-WD1335 Need help? Call 800-305-2204 Step 9: Fasten the lower shelf ( D ) to the ends ( A and B ) and back ( E ) using seven black 1-7/8" flat head screws ( T ). You’ll need: Long finished edge Unf inis hed sur face Phillips screwdriver T (7)

Page 16 - ENGLISH; Distributed by Best Buy Purchasing, LLC; Certificate of Conformity; This certificate applies to the Sauder Woodworking Product

12-0625 ENGLISH www.dynexproducts.com (800) 305-2204 Distributed by Best Buy Purchasing, LLC 7601 Penn Ave. South, Richfield, MN 55423 U.S.A. © 2012 BBY Solutions, Inc. All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and brand names a...

Dynex DX-WD1335 - Manual

Table of Contents:

Summary

Other Dynex Models