Dukane MODEL 8788 - Manual

4 Contents of package Your projector should come with the items shown below. Check that all the items are included. Require of your dealer immediately if any items are missing.(1) Remote control with two AA batteries (2) Power cord (3) Computer cable(4) User’s manuals (Book x1, CD x1) NOTE • Keep th...

5 ENGLISH Preparations Loading batteries into the remote control Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remot...

6 On a horizontal surface Suspended from the ceiling • Keep a space of 30 cm or more between the sides of the projector and other objects such as walls. Do not place or attach anything that would block the lens or vent holes. • For the case of installation in a special state such as ceiling mount, t...

7 ENGLISH VIDEO OUT AUDIO OUT RGB OUT RGB IN S-VIDEO OUT L R AUDIO IN Y C B /P B C R /P R COMPONENT VIDEO OUT L R AUDIO OUT L R AUDIO OUT Connecting your devices Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connect...

8 Connecting power supply 1. Put the connector of the power cord into the AC IN (AC inlet) of the projector. 2. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange. Please remember that when t...

9 ENGLISH Adjusting the projector's elevator When the place to put the projector is slightly uneven to the left or right, use the elevator feet to place the projector horizontally. Using the feet can also tilt the projector in order to project at a suitable angle to the screen, elevating the front s...

10 Displaying the picture 1. Activate your signal source. Turn the signal source on, and make it send the signal to the projector. 2. Use the VOLUME + / VOLUME - buttons to adjust the volume. To have the projector silent, press the MUTE button on the remote control. 3. Press the INPUT button on the ...

11 ENGLISH Turning off the power 1. Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds. 2. Press the STANDBY/ON button again while the message appears. The projector lamp will go off, and the POWER indicator will...

12 Replacing the lamp A lamp has fi nite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early rep...

13 ENGLISH HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ► The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or ...

14 Please check and clean the air fi lter periodically. When the indicators or a message prompts you to clean the air fi lter, comply with it as soon as possible. Replace the fi lters when they are damaged or too soiled. To prepare the new fi lters, make contact with your dealer and tell the followi...

15 ENGLISH Using the CD manual The other manuals for this product are written into the included CD-ROM titled “User’s Manual (detailed)”. Before using the CD-ROM, please read the following to ensure the proper use. System requirements The system for using the CD-ROM requires the following. Windows ®...

16 Speci fi cations Item Speci fi cation Product name Liquid crystal projector Liquid Crystal Panel 786,432 pixels (1024 horizontal x 768 vertical) Lamp 200 W UHB Speaker 1 W Power supply AC 100-120 V/2.9 A, AC 220-240 V/1.4 A Power consumption AC 100-120 V/290 W, AC 220-240 V/270 W Temperature rang...

17 ENGLISH Troubleshooting - Warranty and after-service If an abnormal operation (such as smoke, strange odor or excessive sound) should occur, stop using the projector immediately. Otherwise if a problem occurs with the projector, fi rst refer to the “Troubleshooting” of the “Operating Guide” in th...