Page 2 - Y EAR LIMITED WARRANTY
This Dukane audio visual product is warranted to the original purchaser under a 5 year limited warranty – – in normal use and service – – against defects in material and workmanship. DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,INCLUDING ALL WARRANTIES OF MERCHAN...
Page 3 - IMPORTANT SAFETY INSTRUCTIONS
When using your overhead projector, basic safety precautions shouldalways be followed, including the following: 1. Read and understand all instructions before using.2. Close supervision is necessary when any projector is used by or near children. Do not leave projector unattended while in use. 3. Ca...
Page 4 - Thank you for choosing a
The sleek, low-profile Starfire Overhead Projectors areavailable in your choice of 3000, 4000/3200, 5500/4400and 6000 ANSI lumens. Features of each model vary and caninclude a single, triple or triple/wide-angle lens; built-inAC outlets; and even an electronic “soft start” power supplythat improves ...
Page 5 - TABLE OF CONTENTS; Page
LIFETIME LIMITED WARRANTY ................................. Inside CoverSPECIFICATIONS .................................................................. 1 ELECTRICAL SAFETY GROUNDING INSTRUCTIONS ........................ 1 INDEX OF FUNCTIONAL PARTS ............................................. 2-3 ...
Page 7 - SPECIFICATIONS
SPECIFICATIONS SF MODEL Dimensions ........... 5.6" H x 16.4" W x 17.8" D (Folded) 32" H x 16.4" W x 17.8" D (Opened) HD MODEL Dimensions .......... 8.5" H x 16.4" W x 17.8" D (Folded) 32" H x 16.4" W x 17.8" D (Opened) Aperture ..........................
Page 8 - INDEX OF FUNCTIONAL PARTS
3 2a 9 11 1 6 5 4 7 8 10 2 A number of terms are used frequently in this instruction booklet.The OVERHEAD PROJECTOR will be easier to operate if you becomefamiliar with the terms for the functional parts listed below: INDEX OF FUNCTIONAL PARTS 1. Mirror ; use to direct projected image 2. Projection ...
Page 9 - Door Leg Assembly; Lamp Change Lever
3 12 15 13 14 12. Door Leg Assembly ; close for foldaway design, cord storage 13. Door Latch (one each side) ; keeps doors closed 14. Lamp Change Lever ; slide for replacement/reserve lamp 15. Power Cord; stored in the unit’s base Models 6000 and 4030 also feature a soft start power supply whichexte...
Page 10 - SETUP INSTRUCTIONS SF MODELS
1. Set unit on projection table in the vertical position (handle up). 2. Slide bottom door latches out and swing both doors around to magnet latches. Pull out the entire power cord. Leave doors open. 3. Tip unit over to rest on its legs. (Doors act as feet for the unit). 4. Turn focus knob clockwise...
Page 11 - FOLDUP INSTRUCTIONS; Perform Setup Steps in reverse order.
FOLDUP INSTRUCTIONS 5 Perform Setup Steps in reverse order. • Unlock/lower mast by pushing down on lock collar as shown. S TEP 7 — S TEP 6 —
Page 12 - Set unit on projection table and pull out the power cord from cord; SETUP INSTRUCTIONS HD MODELS
1. Set unit on projection table and pull out the power cord from cord storage compartment. 2. Turn focus knob clockwise until it stops at the end of the mast.3. Rotate mast up until it locks into place.4. Rotate the projection head assembly counterclockwise to the working position. 5. Open mirror. S...
Page 13 - Image Adjustment; A. Position the projected image on screen (height location) by; OPERATION
Place the projector on a stable surface that is desk or table height.Make sure that the side vent is not blocked. Plug the power cordinto a standard 120V AC outlet. Push the power button to turn theprojector on. I = ON O = OFF Place a transparency on the stage. Adjust the focus by turning thefocus k...
Page 14 - If the OHP is brought directly from a cold to a warm; Lamp Changer
CAUTION Do not overload 120V AC outlets with accessories that exceed a total of 5 amps. 8 CAUTION: If the OHP is brought directly from a cold to a warm location or it is placed in a very humid room, moisture may condenseon electrical and optical parts in the unit. If this occurs, wait forOHP to reac...
Page 15 - LAMP REPLACEMENT; WARNING; Remove the lamp by squeezing the lamp retainer clip and
Your projector uses: 3000, 3010 — 360W, ENX.4010, 4030, 5510, 6000 — 410 W, FXL. LAMP REPLACEMENT WARNING Lamp and adjacent metal parts are hot. Allow lamp to cool before replacing. Glass components may shatter. Handle carefully. To Remove an Exhausted Lamp: 1. Remove the lamp by squeezing the lamp ...
Page 16 - CLEANING; Use a soft, lint-free cloth to remove dust from; Shipping Information; SERVICING
10 CLEANING For best performance, keep your projector free of dust and surfacedirt. Keep covered when not in use. Daily Cleaning: Use a soft, lint-free cloth to remove dust from stage glass, projection lens and magnifier lens (6000 and 4030models only). Lens cleaner may also be used on these compone...
Page 17 - TROUBLESHOOTING; Symptom; INFORMATION ON LAMP WARRANTY
11 TROUBLESHOOTING Symptom Probable Cause Solution Neither lamp or a. Unit unplugged a. Plug unit into fan operate outlet b. No power at wall outlet b. Verify outlet has power c. Stage lid not closed c. Close stage lid d. Mirror box not lowered, d. Open bottom (interlock switch not doors and insure ...
Page 18 - OPTIONAL ACCESSORIES SF MODELS; To order
12 OPTIONAL ACCESSORIES SF MODELS FXL LAMP 410W/82V 456-192 (Models 4010, 4030, 5500, 6000) SOFT SHOULDER BAG (PADDED) 128-46 ROLL FILM ADAPTER KIT 438-814 HARD-SIDED CARRYING CASE 185-398 ATA SHIPPING CASE 185-397 ACETATE ROLL (50') 310-6 PROTECTIVE DUST COVER 128-61 ENX LAMP 360W/82V 456-188 (Mode...
Page 19 - OPTIONAL ACCESSORIES HD MODELS
13 OPTIONAL ACCESSORIES HD MODELS FXL LAMP 410W/82V 456-192 (Models 4010, 4030, 5500, 6000) SOFT SHOULDER BAG (PADDED) 128-1 ROLL FILM ADAPTER KIT 438-814 HARD-SIDED CARRYING CASE 185-385 ATA SHIPPING CASE 185-397 ENX LAMP 360W/82V 456-188 (Models 3000/3010) To order accessories, please call 1-800-6...
