Drolet Nova 820 - Manual

ELATION Fireplace Insert 5 SPECIFICATIONS Dimensions: height: 20” (508 mm) width: front: 28” (711 mm) rear: 16” (406 mm) depth: 14 3/4” (375 mm) Surround dimensions: Small Large width: 40” (1016 mm) 44” (1118 mm) height: 25 ½” (648 mm) 27 ½” (699 mm) Glass: 5mm 28" (711 mm) x 11 ¼” (286 mm) 1400...

ELATION Fireplace Insert 6 OPERATION BEFORE LIGHTING 1) Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. 2) Make sure that...

ELATION Fireplace Insert 7 CAUTION: This insert is hot while in operation. Do not touch. Keep children, clothing and flammable materials away. WALL THERMOSTAT To operate your ELATION using the wall thermostat, follow the lighting procedure and set the gas control to the ON position. Simply set your ...

ELATION Fireplace Insert 8 MAINTENANCE INSTRUCTIONS TURN OFF THE GAS WITH THE SHUTDOWN VALVE AND DISCONNECT THE ELECTRICAL POWER BEFORE SERVICING THE APPLIANCE . The venting system and the fireplace insert should be inspected at least once a year. Remove the glass front and the logs and clean them i...

ELATION Fireplace Insert 9 TOP, FRONT AND SIDE VIEWS Note: Views show SMALL surround

ELATION Fireplace Insert 10 INSTALLATION SAFETY NOTICE Improper installation may result in a house fire. Follow installation directions. Installation must be in accordance with local building codes or, in the absence of local codes, with current CAN/CGA B 149 installation codes for gas appliances in...

ELATION Fireplace Insert 11 CLEARANCES Clearance distances between the insert and any combustible material must be maintained while installing your appliance: Clearance to NON combustible hearth is: 0 Clearance to combustible mantel: 38” (965 mm) Clearance to combustible side wall: 10” (254 mm) Mini...

ELATION Fireplace Insert 12 • If you wish to make a direct electrical connection to the blower without using the six-foot cord supplied, route a 120 volt, 60 Hz electrical power supply line to the same location. Remove the power cord and connect the 120V line as per the following procedure : • Unscr...

ELATION Fireplace Insert 13 GLASS FRONT REMOVAL, CLEANING AND INSTALLATION Removal: • Let the insert cool down for at least one hour. • Open the top and bottom louvres to reveal the retaining brackets. • Remove the two (2) screws holding the top bracket and remove the bracket still holding the glass...

ELATION Fireplace Insert 14 BURNER REMOVAL AND INSTALLATION REMOVAL: • Remove the glass front assembly as shown on page 13. • Remove the logs. • Unscrew the line leading to the main orifice under burner (below floor of firebox) and then unscrew the orifice fitting from the burner. • Lift out burner....

ELATION Fireplace Insert 15 EMBER KIT INSTALLATION Three small plastic bags are supplied with your unit. One of the bags contains vermiculite to simulate ashes in the fire box, another contains lava rock to simulate coals and the last one is filled with rock wool fiber which, when glowing red, resem...

ELATION Fireplace Insert 16 LOG INSTALLATION 1. Place rear log in rear log bracket as shown above. 2. Place front log on burner so front log holes fit over front log pins. 3. Place the left hand log so it lays on the left hand edge of the front and rear logs 4. Place the right hand log so it lays on...

ELATION Fireplace Insert 17 BLOWER REPLACEMENT The blower is accessed through the firebox. 1. Unplug the blower cord or switch off circuit breaker. 2. Remove the glass as shown on page 13. 3. Remove logs and burner. 4. Remove the bottom of firebox by removing the 10 screws around the perimeter and t...

ELATION Fireplace Insert 18 SURROUND ASSEMBLY LOUVRE MOUNTING HOLES 1. Lay parts A, B and C on a flat, non marking surface. Fasten these together with the ½ “ bolts and nuts supplied (D). 2. Position the three trim pieces over the surround and connect the ends with corner brackets (E). Ensure the mi...

ELATION Fireplace Insert 19 ADJUSTMENTS NOTE: Adjustments to the valve assembly must be performed by a qualified service person. • The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in exc...

ELATION Fireplace Insert 20 ADJUSTING THE GAS PRESSURE NOTE: If cover plate is already installed, remove it by removing the two screws with a Phillips screw driver. NOTE: The maximum manifold pressure is set at the factory at 3.5” WC for natural gas and 10” WC for propane. To adjust the maximum mani...

ELATION Fireplace Insert 21 ADJUSTING AIR SHUTTER To adjust the air shutter there is an adjustment band below the firebox floor. The factory setting for the air shutter is 1/8” for natural gas, ¼” for propane. After operating the appliance for half an hour or so the flames should have turned a nice ...

ELATION Fireplace Insert 22 OPTIONS DESCRIPTION CODE • Wall thermostat kit E5558 • Ultrasonic remote control E5568 • Conversion kit to propane gas • Conversion kit to natural gas REPLACEMENT PARTS N O . DESCRIPTION................................... CODE 1 P ILOT ASSEMBLY ..............................