Drolet GTX-I - Manual

8 2.3 Heat output adjustment The valve supplied with the appliance has a HI/LO knob to control the heat output and flame height (see Figure 2). 2.4 Fan operation The fan control knob is located on the control panel and may be adjusted to the following settings: OFF: Turn the control fully counter-cl...

9 3.0 INSTALLATION 3.1 Installation and safety notes Read all instructions before starting installation and follow them carefully during installation to ensure maximum benefit and safety. Failure to follow these instructions will void your warranty and may present a fire hazard. See the warranty at ...

10 3.3.2 Gas line installation Install supply line using any piping approved for your installation meeting CAN/CGA 6.10, AA 3, ANSI Z21.24 or Z21.45. A qualified gas fitter should install the gas line in accordance with all local building codes. If codes permit, coiled copper tubing may be used for ...

11 TABLE 2: THERMOSTAT WIRE INFORMATION WIRE SIZE MAX. WIRE LENGTH AWG mm ft . m 22 0.6 10 3.1 20 0.8 25 7.6 18 1.0 40 12.2 16 1.3 64 19.5 14 1.6 100 30.5 2. Solder an appropriate wire connector to each wire. To connect to the burner switch, 1/4" female quick connects are required and to connect...

12 Figure 4 3.3.4 Vent installation 3.3.4.1 Acceptable configurations The stove must be connected to Simpson GS Dura Vent or Security Chimneys International (Secure Vent) 4” x 6 5/8” venting. Install the vent components according to the manufacturer's instructions. Use a maximum of two 90 degree elb...

13 The minimum vertical length using the maximum horizontal length consists of: • A minimum of 24” (61cm) vertical length directly on top of the stove. • A maximum of one 90 degree elbow. • A maximum of 12” (31cm) total horizontal length. • A wall thimble. • A wall thimble cover. • Horizontal termin...

14 3.3.4.2 Typical vent installation Vent terminals shall not be recessed into a wall or siding. Figure 5

15 3.3.4.3 Use of sealant Sealant is required on vent system joints. On longer vent runs, especially vertical runs, sealant will ensure that the combustion air enters from outdoors, and not through the vent joints. Use a sealing product, available from your local Drolet dealer, on the inner pipe joi...

17 HOT Basement Installations To achieve the minimum vertical rise a 36” snorkel must be used. Where the bottom of the terminal may be blocked by snow, ensure provision is made for adequate drainage. 3.3.4.5 Vertical installation Always maintain a 1” clearance around the vent pipe (vertical) and 2” ...

18 Through Roof Framing Maintain 10” opening relative to the pitch of the roof. Use a suitable round or square support through the roof. Ensure adequate heat shield protection is provided. Termination above Roof Consult local codes for minimum vent cap height above the roof . To prevent water seepag...

19 3.3.4.6 Vent terminal locations Figure 7 A = clearances above grade, veranda, porch, deck, or balcony [* 12" (305 mm) minimum] B = clearance to window or door that may be opened [* 12" (305 mm) minimum] C = clearance to permanently closed window [minimum 12" (305 mm) recommended to pr...

21 3.3.6 Initial firing At the time of the first burn, the appliance may emit an odor, accompanied by smoke. This is perfectly normal. As the metal heats to the critical point (about 375 degrees F), part of the paint components turns to light gray smoke as the dormant silicone resin activates and be...

23 4.0 MAINTENANCE 4.1 Maintenance safety Turn off the gas to the main burner and allow the heater to cool for up to 30 minutes before servicing. Service and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a professional serv...

25 5.0 TROUBLE SHOOTING SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION I. Pilot will not light after repeated triggering of the piezo ignition button A. No spark at electrode (weak or not heat source for pilot ignition) 1. Improper ignition 1. Align the electrode with 1/8” (3mm) gap to pilot hood 2. Poor ...

27 6.0 REPLACEMENT PARTS When requesting service or replacement parts, refer to your dealer. The following information’s will be asked for; the model name GTX-I, the type of gas used, serial number and proof of purchase. The damaged parts must be replaced by Drolet genuine parts. You can consult the...

28 DROLET LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. This warranty covers brand new products only, which have not been altered, modified nor repaired since shipment from factory. Proof of purchase (dated bill of...