Page 2 - TABLE OF CONTENTS
1 TABLE OF CONTENTS INTRODUCTION ............................................................................................................... 2 TECHNICAL SPECIFICATIONS ....................................................................................... 3 ASSEMBLY ................................
Page 3 - INTRODUCTION
2 INTRODUCTION SBI INC ., one of the most important wood stove and fireplace manufacturers in Canada, congratulates you on your purchase and wishes to help you get maximum satisfaction from your wood stove. In the pages that follow, we will give you advice on wood heating and controlled combustion a...
Page 4 - TECHNICAL SPECIFICATIONS
3 TECHNICAL SPECIFICATIONS SIBERIAN-1200 SIBERIAN-1600 SIBERIAN-2000 Combustion Type: Wood Wood Wood Recommended Surface 600 à 1 200 ft 2 (56 à 112 m 2 ) 900 à 1 600 ft 2 (84 à 149 m 2 ) 1 000 à 2 000 ft 2 (93 à 186 m 2 ) Heating Capacity : E.P.A : 36 000 BTU/h (10,5kW) 40 000 BTU/h (11,7 kW) 60 200...
Page 5 - ASSEMBLY; PEDESTAL AND DECORATIVE SIDEWALL INSTALLATION
ASSEMBLY PEDESTAL AND DECORATIVE SIDEWALL INSTALLATION Figure 1 : SIBERIAN-1200 and 1600 Pedestal Installation : 1. Remove all bricks and insulations in the appliance. 2. Slowly, lay down the stove on his back. 3. Install legs or the pedestal with the supplied nuts and bolts. Stand up the stove and ...
Page 7 - Figure 4: SIBERIAN-1600 Refractory Bricks Assembly
BRICKS AND INSULATION INSTALLATION (SIBERIAN-1600) 1. Remove from the stove all bricks and insulation. 2. Install all side bricks (12 x 4 1/2" x 9") 3. Install the back bricks (6 x 4 1/2" x 9") 4. Install the bottom bricks (4 x 4 1/2" x 9") + (2 x 6" x 7"). 5. Install...
Page 8 - BRICK AND INSULATION INSTALLATION (SIBERIAN 2000); Refractory Bricks Assembly
BRICK AND INSULATION INSTALLATION (SIBERIAN 2000) The stove is normally supplied with secondary air tubes in position. To install the baffle bricks and white ceramic insulation, it’s necessary to remove the two front secondary air tubes. First place only one baffle brick and one white ceramic insula...
Page 9 - Figure 6: Air Tubes Installation
AIR TUBES INSTALLATION (SIBERIAN 2000): The secondary air tubes are painted different colours . The back tube is yellow, the middle one is red and the front is unpainted. Before installing, make sure the locating holes in the tubes (holes near one end of the tube) are on the left side. Insert one tu...
Page 10 - DOOR ADJUSTMENT; Turn the handle counter clock wise one turn to increase pressure; Figure 7: Door Adjustment
DOOR ADJUSTMENT In order for your stove to operate properly, the door should be adjusted periodically to provide an air tight fit. To adjust: • Remove the lock pin (spring pin) by pulling and turning it using pliers ("wise grip") • Turn the handle counter clock wise one turn to increase pres...
Page 11 - THE BENEFITS OF INSTALLING A BLOWER
THE BENEFITS OF INSTALLING A BLOWER A blower can be installed at the back of your DROLET stove. This option is necessary if you wish to redistribute into a room the heat trapped at the back of your stove. By forcing hot air toward the front, the blower enables you to extend the radiation power of yo...
Page 12 - INSTALLATION; POSITIONING THE STOVE
11 INSTALLATION SAFETY NOTICE • I F THIS STOVE IS NOT PROPERLY INSTALLED , A HOUSE FIRE MAY RESULT . T O REDUCE THE RISK OF FIRE , FOLLOW THE INSTALLATION INSTRUCTIONS . F AILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE , BODILY INJURY , OR EVEN DEATH . • C ONSULT YOUR MUNICIPAL BUILDING...
Page 13 - FLOOR PROTECTOR; FRONT
FLOOR PROTECTOR Your wood stove should be placed on a non-combustible surface. The floor protector should be under the stove, eighteen inches beyond the front and eight inches beyond each side of the fuel loading and ash removal opening. If there is a horizontal section of chimney connector, the flo...
Page 14 - CLEARANCES; A B C D E F; A B C D E F
CLEARANCES It is of utmost importance that the clearances to combustible material be scrupulously respected upon installation of the stove you have selected. Refer to the tables below : Figure 8: Clearances to combustibles Single wall pipe / Double wall pipe CANADA A B C D E F SIBERIAN-1200 15/10 8/...
Page 15 - Sides and
14 REDUCED CLEARANCES You may decrease the clearances by installing heat radiation shields between the walls or the ceiling and the stove. These heat radiation shields must be installed permanently, and can include sheet metal, a rigid non-combustible sheet or a masonry wall. Clearances of not less ...
Page 16 - CHIMNEY
15 CHIMNEY Your wood stove may be hooked up with a factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL 103 or ULC S629 standards; therefore it must be a Type HT (2100°F). It is extremely important that it be installed according to the manufacturer's spe...
Page 17 - Stove Pipe
CHIMNEY CONNECTOR (STOVE PIPE) Your chimney connector and chimney must have the same diameter as the stove outlet. If this is not the case, we recommend you contact your dealer in order to insure there will be no problem with the draught. The stove pipe must be made of aluminized or cold roll steel ...
Page 18 - TYPICAL INSTALLATIONS; FACTORY BUILT CHIMNEY:; Wall installation; Vertical installation
TYPICAL INSTALLATIONS FACTORY BUILT CHIMNEY: ROOF FLASHING 18" CLEARANCE WALL SUPPORT WALL RADIATION SHIELD RAIN CAP Wall installation CEILING SUPPORT RADIATION SHIELD Vertical installation 17
Page 22 - WOODSTOVE UTILIZATION; Average Energy Yield Of One Air Dried Cord Of Cut Wood; Wood species
21 WOODSTOVE UTILIZATION Your heating unit was designed to burn wood only; no other materials should be burnt. Wastes and other flammable materials should not be burnt in your wood stove. Any type of wood may be used in your stove, but specific varieties have better energy yields than others. Please...
Page 23 - under supervision; , in order to allow for good combustion. After this time, you
22 Smaller pieces of wood will dry faster. All logs exceeding 6" in diameter should be split. The wood should not be stored directly on the ground. Air should circulate through the cord. A 24" to 48" air space should be left between each row of logs, which should be placed in the sunnies...
Page 24 - HEATING; Low
HEATING Controlled combustion is the most efficient technique for wood heating because it enables you to select the type of combustion you want for each given situation. The wood will burn slowly if the wood stove air intake control is adjusted to reduce the oxygen supply in the combustion chamber t...
Page 25 - TO PREVENT CREOSOTE BUILD UP
24 RELOADING Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air controls to maximum a few seconds prior to opening the stove's door. Then proceed by opening the door very slowly; open it one or two inches for 5 to 10 seconds, before opening it co...
Page 26 - ASH DISPOSAL
25 ASH DISPOSAL Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep. Always empty the stove when it is cold, such as in the morning. Always dispose of ashes in a metal container with a tight fitting lid. Place this container on a non combustible floor or on ...
Page 27 - MAINTENANCE; GLASS; The glass should be washed only when cold.; GASKETING; PAINT; F heat resistant paint. For this purpose, simply
26 MAINTENANCE Your Drolet stove is a high efficiency stove and therefore require little maintenance. It is important to perform a visual inspection of the stove every time it is emptied, in order to insure that no parts have been damaged, in which case repairs must be performed immediately. GLASS •...
Page 28 - LIMITED LIFETIME WARRANTY
1700, rue Léon-Harmel, Québec (Québec) G1N 4R9 tel. : (418) 527-3060 fax : (418) 527-4311 e-mail : [email protected] web site : www.drolet.ca LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. This warranty covers brand ne...
