Dimplex DXLWP800TI N - Manual
Dimplex DXLWP800TI N – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Suggested Fixings; Drilling Holes; Positioning the Heater; Rear View; Operation; OPERATION - SINGLE RATED MODELS
- Page 3 – Position O - Heating Off; IMPORTANT NOTES; e timer clock
- Page 4 – For electrical products sold within the European Community.; After Sales Service
Dimplex Low Wattage Panel Heaters
Models: DXLWP400, DXLWP400TI,
DXLWP800, DXLWP800TI N & ARLWP800TI
Installation and Operating Instructions
Dimensions
(millimetres)
Models
Specification
DXLWP400
400W Neon Heat Switch
DXLWP400TI
400W Neon Heat Switch / 24 Hour Timer
DXLWP800
800W Neon Heat Switch
DXLWP800TI N
800W Neon Heat Switch / 24 Hour Timer
ARLWP800TI
800W 2 Neon Heat Switches / 24 Hour Timer
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Electrical Connection
WARNING THIS APPLIANCE MUST BE EARTHED
If the socket outlets in your home are not of the 13 amp BS1363
type they will not accept the plug connected to this heater, therefore
cut off the plug. When cut off this plug can constitute a shock
hazard if inserted into a socket outlet. It must therefore be
disposed of safely.
Before wiring the appropriate plug please note that the wires in
this mains lead are coloured in accordance with the following
code.
GREEN/YELLOW:
EARTH
BLUE:
NEUTRAL
BROWN:
LIVE
Connect the
Green/Yellow
wire to the terminal marked
E
or the
earth symbol
or coloured
Green
or
Green/Yellow
.
Connect the
Brown
wire to the terminal marked
L
or coloured
Red
.
Connect the
Blue
wire to the terminal marked
N
or coloured
Black
.
DO NOT
connect the
Brown
(
Live
) or the
Blue
(
Neutral
) wires to
the
Earth
terminal of your 13 amp plug. If the terminals of the
plug are unmarked or you are in any doubt, consult a qualified
electrician.
CAUTION:
If you use this heater in conjunction with a thermal
control, programme controller, timer or any other device which
switches the heater on automatically observe all safety warnings
at all times.
600 mm - 400W
800 mm - 800W
500 mm
Important Safety Advice
WARNING –THIS APPLIANCE MUST NOT BE USED IN A
BATHROOM.
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING
POOL.
WARNING – THIS HEATER MUST NOT BE LOCATED
IMMEDIATELY BELOW A FIXED SOCKET OUTLET.
The plug must be accessible after heater installation.
DO NOT USE THE HEATER UNTIL THE FEET OR WALL
BRACKETS ARE FITTED CORRECTLY.
FOLLOW these instructions carefully.
The heater carries a warning ‘DO NOT COVER’ to alert the
user to the risk of fire that exists if the heater is
accidentally covered.
Models DXLWP400TI, DXLWP800TIN and ARLWP800TI
can be set to switch on automatically. Remember to
observe all safety warnings at all times.
This appliance is not intended for use by children or other
persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
If young children, the aged or infirm are likely to be left in
the vicinity of the heater, we advise that adequate
precautions should be taken. We recommend a guard
be fitted to ensure contact with the heater is avoided and
objects cannot be inserted into the product.
If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
For further information, please contact our guard supplier
direct on Tel. No. 01603 667957, or in case of difficulty or
for further advice contact the Customer Helpline.
INDUKLWPRG Issue 6
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Installation The Fixing Kit should contain: 1 Drilling Template, 3 Screws, 3Rawlplugs, 1 Mounting Bracket and 1 Hexagon Key. Wall Mounted Operation (see Fig. 2 ) Suggested Fixings SOLID BRICK/BLOCK: No. 8 Rawlplug inserts, 6mm drill bit. PLASTERBOARD: If possible locate studding and use No. 8 woodsc...
Models with TimerDXLWP400TI, DXLWP800TI N & ARLWP800TI Set the I - ¡ ¡ ¡ ¡ ¡ - O sli de switch on the timer ( Fig. 3 ) to : Position O - Heating Off Position I - Manual operation This setting allows power to the heateruninterrupted by the timer settings. Theheat selector switch will control the ...
Cleaning WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLYBEFORE CLEANING THE HEATER. Do not use detergents, abrasive cleaning powder or polish ofany kind on the body of the heater.Allow the heater to cool, then wipe with a dry cloth to remove dustand a damp cloth (not wet) to clean off stains. Be c...
