Dewalt NS150A- User Manual

Page 2 - GB

2 PORTER ✦✦ CABLE Porter-Cable Corporation4825 Highway 45 NorthJackson, TN 38305 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ordre GB ENGLISH EC-DECLARATION OFCONFORMITY We d...

Page 3 - SAFETY GUIDELINES / DEFINITIONS; SAVE THESE INSTRUCTIONS!; IMPORTANT SAFETY INSTRUCTIONS

3 indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. indicates a potentially hazardous situation which, if not avoided, may result in mi...

Page 4 - GENERAL SAFETY RULES

4 Fig. 6 Fig. 5 Fig. 2 Fig. 3 Fig. 4 1. Read and understand tool labels andmanual. Failure to follow warnings could result in DEATH or SERIOUS INJURY . Fig. 1. 2 . Operator and others in work area MUST wear safety glasses with side shields. These safety glasses must conform to ANSIZ87.1 requirements...

Page 6 - TECHNICAL SPECIFICATIONS

6 21. Remove finger from trigger when not driving fasteners. Never carry tool with fingeron trigger. In “Contact Actuation Mode” toolwill fire a fastener if safety is bumped whiletrigger is depressed. Fig. 14. 22. Do not overreach. Keep proper footing a n d b a l a n c e a t a l l t i m e s w h e n ...

Page 7 - lengths from; Use approved Porter-Cable fasteners only.; POWER SOURCE; The tool is equipped with a; EMPLOYER’S RESPONSIBILITIES

7 Employer must enforce compliance with the safety warnings and all otherinstructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understandtool labels and manual. Failure to fol...

Page 8 - PREPARING THE TOOL

8 PREPARING THE TOOL 1. After reading and understanding this entire manual, connect tool to air supply (Fig. 18). 2. Pull staple follower all the way to the rear (A) Fig. 19, allowing follower to lock in the open position. 3. Drop a strip of staples onto the guide rail (A Fig. 20). 4. Depress the fo...

Page 9 - USING THE TOOL WITH SELECTABLE TRIGGERING OPTIONS; OPERATING INSTRUCTIONS

9 USING THE TOOL WITH SELECTABLE TRIGGERING OPTIONS Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a selectable trigger set in the “SINGLE SEQUENTIAL ACTUATION” firing mode as described in number 1 below. The selectable trigger can be set f...

Page 10 - RUBBER NOSE CUSHION; Disconnect tool from air supply before removing or

10 The depth to which a fastener is driven is controlled by the depth adjustmentknob (A) Fig. 25. The depth of drive is factory adjusted to a nominal setting.Test fire a fastener and check depth. If a change is desired, rotate theadjustment knob (A) Fig. 25. The adjustment knob has detents every 1 /...

Page 11 - CLEARING A JAMMED FASTENER; Disconnect tool from air supply.

11 CLEARING A JAMMED FASTENER Disconnect tool from air supply. 1. Hold open spring loaded magazine cover (A) Fig. 28 and remove any remaining fasteners (B) Fig. 29. Remove fasteners from tool before opening the fastener guide plate. Fasteners are under pressure and may shootout of magazine which cou...

Page 12 - CLEAN AND INSPECT DAILY; D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d; SERVICE AND REPAIRS; MAINTENANCE

12 CLEAN AND INSPECT DAILY D i s c o n n e c t t o o l f r o m a i r s u p p l y b e f o r e c l e a n i n g a n d inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammablecleaning solutions to wipe exterior of tool only i...

Page 13 - TROUBLESHOOTING; Disconnect tool from air supply before performing any Service

13 TROUBLESHOOTING Disconnect tool from air supply before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Air leak near top of Loose screws. Tighten screws. tool or in trigger area. Worn or damaged Install Overhaul Kit. o-rings or seals. 2. Tool does nothing or Inadequate air supply....

Page 14 - for a catalog or for the name of your nearest supplier.; ACCESSORIES

14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, pr...

Table of Contents:

Summary

Other Dewalt Models