Dewalt 692-1600 - Manual

23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180 Fax. 714.692.5016

www.cobrausa.com

12/04

*

C o b r a r e c o m m e n d s y o u a l w a y s w e a r a h e l m e t w h i l e r i d i n g . P l e a s e n e v e r o p e r a t e y o u r m o t o r c y c l e w h i l e u n d e r

t h e i n f l u e n c e o f a l c o h o l a n d / o r d r u g s . E n j o y t h e n e w l o o k o f y o u r m o t o r c y c l e a n d p l e a s e r i d e s a f e l y .

Items Supplied >

1 – Fi2000R Fuel Injection Module

2 – Zip Ties

Application(s) >

HARLEY 95-Up

FLH

W/Fuel Injection

FLHT

FLHS

FLTR

ROADKING

Instruction Manual >

Read all instructions ca refully and completely before installing your new Fi2000 module.

It is recommended that a qualified mechanic or technician install this product.

1.

Remove the seat and air cleaner assembly.

2.

Remove both front and rear gas tank mounting bolts.

3.

Prop the rear of the gas tank up approximately 2”.

4.

Locate the factory connector on each fuel injector. Depress the wire clip on the injector and pull
the connector free and move out of way.

Note:

A pair of needle nose pliers and a long flat blade

screwdriver helps with this job. If you have a 2002 or newer Harley see the additional instructions
on sheet 2.

5.

Lay the Fi2000 module in place, but do not attach it to the motorcycle, and run the wiring harness
up to the manifold area behind the other wiring of the throttle body (See figure 1). Attach the
Fi2000 module’s forward injector plug, with the grey and red wires, onto the front injector. Then
take the original HD connector and insert the corresponding Fi2000 connector, with the brown and
red wires, into it. (For model years 02’ and Up refer to figure 2, for model years 95-01 refer to
figure 3)

6.

Attach the Fi2000 module’s rear injector plug, with the blue and red wires, onto the rear injector.
Then take the original HD connector and insert the corresponding Fi2000 connec tor, with the
green and red wires, into it. (For model years 02’ and Up refer to figure 2, for model years 95-01
refer to figure 3)

7.

Before re-installing the gas tank, seat and air cleaner assembly, verify your connections. Remove
the door from the Fi2000 box to expose the LED’s. Verify the wire connections by (1) turning the
ignition on, prior to starting, and see if all three LED’s are on steady. If you have no light, your
ground connection (BLACK wire) has not made proper contact or your front injector connection is
not complete. (2) After achieving a steady light from all three LED’s, start the motorcycle, wait 15
seconds and let it idle, the green light should now be the only LED on. If all three LED’s are still on
after start up, verify you have attached the injector connectors correctly. Reattach the door when
finished.

Note:

Make sure the ignition is turn off before changing any

connection.

8.

Route the Fi2000 wiring harness along side the factory harness using the supplied zip ties,
keeping it off the cylinder head or getting it pinched under the gas tank. Lower and re-attach the
fuel tank.

9.

Remove the backing from the Velcro and attach the Fi2000 next to the battery as shown in fig 1.

10.

Re-install the seat and air cleaner assembly.

692-1600

Page 1 of 4

DOCUMENT NO. 0017

REV. A