Dewalt 36-485- User Manual

5 1. Combination Dust Chute/ Support Panel 2. Motor Pulley3. Motor4. Pulley Guard5. Drive Belt6. Spring7. Pins (2) for Mounting Motor8. Motor Mounting Plate9. Lockwashers (4) 10. Flat Washers (4)11. 5/16-18 x 3/4 Carriage Head Screws (4) 12. Hex Nuts (4)13. 5/16 Hex Nuts (8)14. 5/16 Lockwashers (8)1...

6 BIESEMEYER T-SQUARE FENCE SYSTEM The T-Square ® Commercial Fence System includes the fence assembly, front rail, rear rail, front guide tube and right extension table Model 78-927 for 30 capacity. IMPORTANT: The T-Square ® Fence System is designed to be used ONLY with a supporting extension table....

9 ASSEMBLY INSTRUCTIONS Fig. 8 Fig. 9 Fig. 10 ASSEMBLING SAW STAND 1. Assemble the dust chute and support panel (A) Fig. 8, to the inside of the front stand panel (B) with three#10 x 1/2 sheet metal screws (C), four #10-32 x 1/2screws (D), and four hex nuts (E). Fig. 9 illustrates thedust chute and ...

11 MOTOR The motor shipped with your saw is a 1-1/2 H.P., Ball Bearing, Capacitor Start/Capacitor Run, 115/230Volt motor. This motor has been specially selected to best supply power to your machine and the relative safetyof the machine is enhanced by its use. We, therefore, strongly suggest that onl...

29 GROUNDING INSTRUCTIONS CAUTION: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATORFROM ELECTRIC SHOCK. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reducethe risk of electric shock. The motor is equipped with an ele...

31 Fig. 97 A FASTENING STAND TO SUPPORTING SURFACE IF DURING OPERATION THERE IS ANY TENDENCY FOR THE SAW TO TIP OVER, SLIDE OR WALK ONTHE SUPPORTING SURFACE, THE SAW STAND CAN BE SECURED TO THE FLOOR SURFACE. THERUBBER FEET OF THE STAND FEATURE HOLES WHICH ALLOW EASY MOUNTING WITHOUT REMOV-ING THE S...

32 Fig. 98 Fig. 99 RAISING AND LOWERINGTHE BLADE To raise the saw blade, loosen lock knob (A) Fig. 98, andturn the blade raising handwheel (B) clockwise. Whenthe blade is at the desired height, tighten lock knob (A). To lower the blade, loosen lock knob (A) Fig. 98, and turnthe handwheel (B) counter...

33 BACKLASH ADJUSTMENTS FOR BLADE RAISINGAND BLADE TILTING MECHANISMS After a period of extended use, if any play is detected inthe blade raising or blade tilting mechanisms, the follow-ing adjustments should be made. 1. Make certain the machine is disconnected from the power source . 2. NOTE: The m...

ADJUSTING BLADE ALIGNMENT WARNING: Blade Alignment is Factory Set and shouldnot need adjustment. Adjusting Blade Alignment, in thefield, is a difficult and time-consuming procedure. AllSaw Blades have some run-out, therefore re-adjustingblade alignment should only be attempted if it becomesnecessary...

36 Fig. 108 Fig. 109 Fig. 111 STORING THE MITER GAGE,RIP FENCE, AND ARBORWRENCHES 1. When not in use, the miter gage (A) Fig. 108, can be stored through the hole located at the front side of thestand as shown. 2. The rip fence (B) Fig. 108, can be conveniently stored out-of-the-way on the stamped le...

39 OPERATIONS CROSS-CUTTING Cross-cutting requires the use of the miter gage to position and guide the work. Place the work against the miter gageand advance both the gage and work toward the saw blade, as shown in Fig. 120. The miter gage may be used in eithertable slot. When bevel cutting (blade t...

43 Fig. 135 C It is necessary when using the moulding cutterhead toadd wood-facing (C) to the face of the rip fence, asshown in Fig. 135. The wood-facing is attached to thefence with wood screws through holes which must bedrilled in the fence. 3/4 inch stock is suitable for mostwork although an occa...

44 Fig. 139 The dado head set (D) Fig. 139, is assembled to the sawarbor as shown. IMPORTANT: The blade guard and splitter assembly cannot be used when dadoing andmust be removed or swung to the rear of the saw asexplained previously in this manual. Auxiliary jigs,fixtures, push sticks and feather b...

45 BIESEMEYER T-SQUARE FENCE SYSTEM FENCE OPERATION IMPORTANT: Before operating fence, make sure the fence is adjusted parallel tothe miter gage slot, as explained later on in this manua l. Fig. 142 Fig. 143 1. To move the fence along the guide rail, simply lift up clamp lever (A) as shown in Fig. 1...

46 LUBRICATION 1. Apply paste wax to fence and guide tube sliding sur- faces weekly. Also, saw table and extension table surfaceshould be waxed often. 2. Apply grease to cam lock (A) Fig. 149, and cam foot (B) occasionally to prevent wear. ADJUSTING CLAMPING ACTION OF FENCELOCKING HANDLE When the fe...

47 CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily bemade from scrap material by following the pattern shown in Fig.150. Fig. 150 PUSH STICK MAKE FROM 1/2 OR 3/4 WOOD OR THICKNESS LESS THAN WIDTH OF MA T’L. TO BE ...

48 The testing of this unit has been accom-plished with the following accessories.For safest operation, it is recommendedthat only these accessories be used withthis unit. WARNING: Since accessories other than those listed have not been testedwith this unit, use of such accessoriescould be hazardous...

51 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are servicedby a network of Porter-Cable/Delta Factory Service Centers and Delta Authorized ServiceStations. To obtain additional information regarding your Delta quality produc...