Delta SH100 - Manual - manualsarea.com

Page 2 - GENERAL SAFETY RULES

2 GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with the operation of the product. Using the machine with respect and caution willconsiderably lessen the possibility of personal inj...

Page 3 - SAVE THESE INSTRUCTIONS; Refer to them often

3 ADDITIONAL SAFETY RULES FOR FOR THE ROUTER/SHAPER WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY Fig. B 21. USE A HEAVY WORKPIECE when shaping with starting pin and collar(s). DO NOT SHAPE a short, light workpiece against the collar(s) (Figs. D and E). Fig. D Fig. E F...

Page 5 - EXTENSION CORDS; OPERATING INSTRUCTIONS; FOREWORD; UNPACKING AND CLEANING; NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord whichhas a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using anextension cord, be sure to use one heavy enough to carry the current of the ...

Page 6 - ROUTER / SHAPER PARTS

6 ROUTER / SHAPER PARTS Fig. 2 1. Router / Shaper 2. 1¼" Open End Arbor Wrench 3. Collet Wrench 4. 3mm Hex wrench 5. Left Hand Fence Body 6. Right Hand Fence Assembly 7. Spindle Knob 8. Fence Knob (2) 9. Cutter Guard Bracket 10. Template Guide Insert11. Wooden Fence (2)12. 1/2" Collet with N...

Page 7 - ASSEMBLY; FEET

7 ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED. DO NOT OPERATE THIS MACHINE UNTIL YOU READ ANDUNDERSTAND THE ENTIRE INSTRUCTION MANUAL OVERHEAD CUTTER GUARDBRACKET Assemble the overhead cutter guard holding bracket (A...

Page 9 - OPERATING CONTROLS AND ADJUSTMENTS

9 ASSEMBLINGTABLE INSERT The table insert (A) is assembled in the table, as shownin Fig. 11. Fig. 11 FASTENINGROUTER/SHAPERTO SUPPORTINGSURFACE IF DURING OPERATION THERE IS ANY TENDENCYFOR THE ROUTER/SHAPER TO TIP OVER, SLIDE ORWALK ON THE SUPPORTING SURFACE, THEROUTER/SHAPER SHOULD BE SECURED TO TH...

Page 10 - OVERLOAD PROTECTION; FENCE ADJUSTMENTS

10 OVERLOAD PROTECTION The Router/Shaper is equipped with overload protection.If the motor shuts off, or fails to start due to overloading(cutting stock too fast; using dull bits and cutters; usingthe machine beyond its capacity or at low voltage, etc.), TURN THE SWITCH (A) FIG. 16, TO THE “OFF”POSI...

Page 13 - INSTALLING ROUTER BITS; STARTING PIN

13 Fig. 27 Fig. 28 Fig. 29 Fig. 30 A D C H E F G A B B A A K B INSTALLING ROUTER BITS 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Raise spindle to the maximum height and tighten lock knob. 3. This machine is supplied with a 1/2 inch collet (A) Fig. 27, that accepts 1/2 inch shank router bits. A 1/4i...

Page 15 - OPERATION; ROUTING OR SHAPING WITH COLLARS AND STARTING PIN

15 OPERATION The following is an example of the setting-up and operational procedures when using the fence, collars andstarting pin. Please review this information carefully before turning on the power to avoid damage to themachine or personal injury. WARNING: The use of accessories and attachments ...

Page 17 - NOTES

Page 18 - Two Year Limited Warranty; PARTS, SERVICE OR WARRANTY ASSISTANCE

Two Year Limited Warranty Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven to be defective in workmanship or material, provided that the customer returns the productprepaid to a Delta factory service c...

Delta SH100 - Manual

Table of Contents:

Summary

Other Delta Models