Delta 40-650 Type 2 - Manual

Page 5 - UNPACKING AND CLEANING

5 Fig. 2 UNPACKING AND CLEANING Your new scroll saw and stand is shipped complete in one container. Carefully unpack the saw, stand and all looseitems from the shipping container. Figure 2 illustrates the saw and all loose items and Figure 3 illustrates the standand all related parts. Remove the pro...

Page 6 - ASSEMBLING STAND; ASSEMBLY INSTRUCTIONS

6 Fig. 3 ASSEMBLING STAND 1. Assemble the stand, as shown in Fig. 4,using the 24 carriage bolts, flat washers andhex nuts. NOTE: The round holes on the topof the two top braces (A) are to be positionedtoward the rear leg (B) and all three legs arepositioned outside the bottom shelf and topbraces. DO...

Page 7 - D E

7 Fig. 5 Fig. 6 Fig. 7 Fig. 8 3. Figure 8 illustrates the saw (H) fastened tothe stand (J). Place the stand on a level sur-face and securely tighten all stand mountinghardware. 2. Fasten the rear of the saw to the standusing the two5/8" long screws (F) Fig. 6, and lock washers(G). The 5/8" l...

Page 8 - ASSEMBLING TABLE INSERT

8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 ASSEMBLINGHOLDDOWN FOOT 1. With wrench supplied, assemble holddownfoot (A) Fig. 10, to rod (B) using 1/2² hex sock-et head screw (C)with lockwasher and flat washer. Prongs ofholddown foot (A) should straddle blade.2. Adjustment to holddown rod (B) Fig. 10,can be made...

Page 9 - CONNECTING SCROLL SAW TO POWER SOURCE; GROUNDING INSTRUCTIONS; EXTENSION CORD SIZE

9 CONNECTING SCROLL SAW TO POWER SOURCE IMPORTANT: BEFORE CONNECTING THE SAW TO THE POWER LINE, MAKE SURE THE SWITCH IS IN THE “OFF”POSITION. Fig. 15 Fig. 14 GROUNDED OUTLET BOX CURRENTCARRYINGPRONGS GROUNDING BLADE ISLONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER In the event o...

Page 10 - IMPORTANT; : We suggest that when the scroll

10 FASTENING STAND TO SUPPORTING SURFACE If there is any tendency for the scroll saw to move during operation, the scroll saw stand must befastened to the floor. Fig. 17 OPERATING CONTROLS AND ADJUSTMENTS ON-OFF POWER SWITCH The on-off switch (A) Fig. 16, is located on the top of the arm, as shown. ...

Page 11 - DUST BLOWER; ADJUSTING BLADE TENSION

11 Fig. 18 DUST BLOWER A dust blower (A) Fig. 18, is provided, and canbe moved to direct air to the most effectivepoint on the cutting line. ADJUSTING BLADE TENSION Tension is applied to the blade when the blade tension lever (A) Fig. 19, is in the rear position, asshown. When the lever (A) is moved...

Page 13 - CHANGING BLADES

13 Fig. 25 3. Push blade holder clamping lever (C) Fig. 25, to the rear as shown. This will automatically release the blade(D) from the upper blade holder (E). 4. Push lower blade holder clamping lever (F) Fig. 26, to the rear. This will automatically release blade (D) fromlower chuck. 5. Remove bla...

Page 14 - TILTING THE TABLE

14 Fig. 27 Fig. 28 Fig. 29 Fig. 31 ADJUSTING 90 AND 45DEGREE POSITIVE STOPSFOR TABLE 1. Loosen table lock handle and move the table all the way to the left and tighten table lock handle. 2. Using a square (A) Fig. 29, check to see if the table is 90 degrees to the saw blade, as shown. 3. If the tabl...

Page 16 - BLADE BREAKAGE; Blade breakage is usually caused by one or more of the following:; CHOICE OF BLADE AND SPEED; Use a blade that will have 2 teeth in the workpiece at all times.; FUSE REPLACEMENT

16 BLADE BREAKAGE Blade breakage is usually caused by one or more of the following: 1. Bending the blade during installation.2. Improper blade tension.3. Improper blade selection for the workbeing cut. 4. Forcing the work into the blade too rapidly.5. Cutting too sharp a turn for the bladebeing used...

Delta 40-650 Type 2 - Manual

Table of Contents:

Summary

Other Delta Models