Dell W-IAP103- User Manual

Page 3 - Command Syntax—The complete syntax of the command.; Intended Audience

Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide About this Guide | 3 Chapter 1 About this Guide This document describes the Dell Networking W-Series Instant command syntax and provides the followinginformation for each command: l Command Syntax—The complete syntax of the command. ...

Page 4 - Italics; Boldface; Commands; Typographical Conventions; Indicates a risk of damage to your hardware or loss of data.; Contacting Dell; Support; Main Website; Support Information

4 | About this Guide Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Type Style Description Italics This style is used for emphasizing important terms and to markthe titles of books. Boldface This style is used for command names and parameter optionswhen mentioned in the text. Com...

Page 5 - New Commands; Command

What is New in Instant 6.4.0.2-4.1 This section lists the new and modified commands in the Instant 6.4.0.2-4.1 release. New Commands The following commands are added in the Instant 6.4.0.2-4.1 release: Command Description console Allows you to enable or disable access to the W-IAP console. dpi Enabl...

Page 6 - Modified Commands

6 | About this Guide Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Modified Commands The following commands are modified in the Instant 6.4.0.2-4.1 release: Command Description airgroup This command now allows you to enable DLNA and mDNS (Bonjour services) support on aW-IAP for ...

Page 7 - To enable the SSH access to the Instant CLI:; Connecting to a CLI Session; Applying Configuration Changes

Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Instant CLI | 7 Chapter 1 Instant CLI Instant supports the use of Command Line Interface (CLI) for scripting purposes. You can access the Instant CLIthrough a Secure Shell (SSH). To enable the SSH access to the Instant CLI: 1. From t...

Page 8 - Configuration Sub-modes

8 | Instant CLI Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide To apply the configuration changes to the cluster, without saving the configuration, use the following command in theprivileged mode: (Instant AP)# commit apply no-save To view the changes that are yet to be applied, ...

Page 9 - Using Sequence Sensitive Commands; Sequence-Sensitive Command; no opendns; Sequence-Sensitive Commands; Saving Configuration Changes; Commands that Reset the W-IAP; The; reload

Using Sequence Sensitive Commands The Instant CLI does not support positioning or precedence of sequence-sensitive commands. Therefore, it isrecommended that you remove the existing configuration before adding or modifying the configuration details forsequence-sensitive commands. You can either dele...

Page 10 - Command Line Editing; To view items in the command history, use the; up; arrow key to move back through the list and the; down; arrow key to; Line Editing Keys

10 | Instant CLI Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command Line Editing The system records your most recently entered commands. You can review the history of your actions, or reissue arecent command easily, without having to retype it. To view items in the command hi...

Page 11 - Specifying Addresses and Identifiers in Commands; Description; IP address; Addresses and Identifiers

Specifying Addresses and Identifiers in Commands This section describes addresses and other identifiers that you can reference in CLI commands. Address/Identifier Description IP address For any command that requires entry of an IP address to specify a network entity,use IPv4 network address format i...

Page 12 - Authentication is successful; Version; This command is introduced.; Command Mode; All platforms

12 | aaa test-server Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide aaa test-server aaa test-server <servername> <username> Description This command tests a configured authentication server. Syntax Parameter Description <servername> Allows you to specify the aut...

Page 13 - This command configures 5 GHz radio channels for a specific W-IAP.; Configures the specified 5 GHz channel.; The following example configures the 5 GHz radio channel:

a-channel a-channel <channel> <tx-power> Description This command configures 5 GHz radio channels for a specific W-IAP. Syntax Parameter Description Range <channel> Configures the specified 5 GHz channel. The valid channels for a bandare determined by the APregulatory domain. <t...

Page 14 - This command configures external antenna connectors for a W-IAP.; Syntax; Parameter; Usage Guidelines; Install Guide; that is shipped along with the AP device.; EIRP and Antenna Gain; The following table describes this formula:; Formula Variable Definitions; Example

14 | a-external-antenna Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide a-external-antenna a-external-antenna <gain> Description This command configures external antenna connectors for a W-IAP. Syntax Parameter Description Range <gain> Configures the antenna gain. You ...

Page 15 - Command History; Command Information

Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide a-external-antenna | 15

Page 16 - Disabled; The following example configures the Aeroscout RTLS server:; Command was introduced.

16 | aeroscout-rtls Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide aeroscout-rtls aeroscout-rtls <IP-address> <Port> [include-unassoc-sta] no... Description This command configures the Aeroscout Real-Time Asset Location Server (RTLS) settings for Instant and sends the...

Page 17 - airgroup; This command configures the AirGroup settings on a W-IAP.; Enabled

airgroup airgroup cppm enforce-registration cppm-query-interval <interval> cppm-server <server-name> disable enable [dlna-only| mdns-only] enable-guest-multicast multi-swarm no… Description This command configures the AirGroup settings on a W-IAP. Syntax Parameter Description Range Defau...

Page 18 - The following example configures an AirGroup profile:; This command is modified.

18 | airgroup Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Range Default multi-swarm Enables inter cluster mobility. Whenenabled, the W-IAP shares the mDNSdatabase information with the otherclusters. The AirGroup records in theVirtual Controller can be sha...

Page 19 - airgroupservice; disable; Specifies the AirGroup service to configure.

airgroupservice airgroupservice <airgroupservice> description <description> disable disallow-role <role> disallow-vlan <VLAN-ID> enable id <AirGroupservice-ID> no… Description This command configures the availability of AirGroup services for the W-IAP clients. Syntax Pa...

Page 20 - The following example configures AirGroup services:

20 | airgroupservice Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Default disallow-vlan <VLAN-ID> Restricts the AirGroup servers connected on thespecified VLANs from being discovered. Disabled enable Enables the AirGroup service for the profile. — id...

Page 21 - no...; The following command enables W-AirWave RTLS:

airwave-rtls airwave-rtls <IP-address> <Port> <key> <frequency> [include-unassoc-sta] no… Description This command integrates W-AirWave Real-Time Asset Location Server (RTLS) settings for Instant and sends theRadio-frequency identification (RFID) tag information to a W-AirWav...

Page 22 - The following example configures the ALE server details:

22 | ale-report-interval Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ale-report-interval ale-report-interval <seconds> no… Description This command configures the interval at which a W-IAP sends data to the Analytics and Location Engine (ALE)server. Syntax Command/Parame...

Page 23 - Use this command to enable a W-IAP for ALE support.

ale-server ale-server <server> no… Description This command configures Analytics and Location Engine (ALE) server details for W-IAP integration with ALE. Syntax Command/Parameter Description ale-server <server> Allows you to specify the Fully Qualified Domain Name (FQDN) or IPaddress of ...

Page 24 - alg; The following example configures the ALG protocols:

24 | alg Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide alg alg sccp-disable sip-disable vocera-disable no… Description This command allows you to modify the configuration settings for Application Layer Gateway (ALG) protocolsenabled on a W-IAP. An application-level gateway consi...

Page 25 - This command allows the new access points to join the W-IAP cluster.; Allows new access points in the domain.; The following command allows the new W-IAPs to join the cluster.

allow-new-aps allow-new-aps no… Description This command allows the new access points to join the W-IAP cluster. Syntax Command/Parameter Description allow-new-aps Allows new access points in the domain. no Removes the specified configuration parameter. Usage Guidelines Use this command to allow the...

Page 26 - This command allows an AP to join the W-IAP cluster.; Use this command to allow a W-IAP to join the cluster.

26 | allowed-ap Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide allowed-ap allowed-ap <MAC-address> no… Description This command allows an AP to join the W-IAP cluster. Syntax Command/Parameter Description allowed-ap <MAC-address> Specifies the MAC address of the W-IAP...

Page 27 - The following command configures a W-AirWave backup server.

ams-backup-ip ams-backup-ip <IP-address or domain name> no… Description This command adds the IP address or domain name of the backup W-AirWave Management server. Syntax Parameter Description <IP-address or domain name> Configures the IP address or domain name of the secondary W-AirWaveM...

Page 30 - This command assigns a shared key for service authorization.

30 | ams-key Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ams-key ams-key <key> no… Description This command assigns a shared key for service authorization. Syntax Parameter Description <key> Authorizes the first Virtual Controller to communicate with the W-AirWaves...

Page 31 - apply

apply apply {cplogo-install| cplogo-uninstall| debug-command| delta-config} Description This command is used to save or apply the configuration settings on the W-IAP. Syntax Parameter Description cplogo-install Installs the Captive Portal logo on the W-IAP. cplogo-uninstall Uninstalls the Captive Po...

Page 32 - arm; Configures 5 GHz channels.

32 | arm Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide arm arm 80mhz-support a-channels <a-channel> air-time-fairness-mode {<default-access>| <fair-access>| <preferred-access>} band-steering-mode {balance-bands|prefer-5ghz| force-5ghz| disable} client-awa...

Page 34 - Configures a hold time for client match.

34 | arm Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command/Parameter Description Range Default error, 2—information,3—debug,4—dump holdtime <number> Configures a hold time for client match. 1—1800 900 max-adoption <count> Configure a maximum number for adoptingcl...

Page 35 - The following example configures an ARM profile:

Command/Parameter Description Range Default frequency bandwidth available for datatransmission. For high performance, enter5GHz. If the AP density is low, enter2.4GHz. no… Removes the current value for thatparameter and return it to its default setting — — Usage Guidelines Use this command to config...

Page 36 - attack

36 | attack Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide attack attack drop-bad-arp-enable fix-dhcp-enable no… poison-check-enable Description This command enables firewall settings to protect the network against wired attacks, such as ARP attacks ormalformed DHCP packets, and ...

Page 37 - The following example blacklists the clients dynamically:

auth-failure-blacklist-time auth-failure-blacklist-time <seconds> Description This command allows the W-IAPs to dynamically blacklist the clients when they exceed the authentication failurethreshold. Syntax Parameter Description Default auth-failure-blacklist- time <seconds> Configures t...

Page 39 - Adds the MAC address of the client to the blacklist.; Use this command to blacklist the MAC addresses of clients.

blacklist-client blacklist-client <MAC-address> no… Description This command allows you to manually blacklist the clients by using MAC addresses of the clients. Syntax Parameter Description blacklist-client <MAC-address> Adds the MAC address of the client to the blacklist. no… Removes th...

Page 41 - calea; calea; Dell Networking W-Series Instant User; The following example configures a CALEA profile:

calea calea encapsulation-type <gre> ip <IP-address> ip mtu <size> gre-type <type> no... Description This command creates a Communications Assistance for Law Enforcement Act (CALEA) profile to enable W-IAPsfor Lawful Intercept (LI) compliance and CALEA integration. Syntax Com...

Page 43 - PAP

cellular-uplink-profile cellular-uplink-profile <profile> 4g-usb-type <4G-usb-type> modem-isp <modem_isp> modem-country <modem-country> usb-auth-type <usb_authentication_type> usb-dev <usb-dev> usb-dial <usb-dial> usb-init <usb-init> usb-modeswitch <...

Page 44 - Specifies the modem tty port.; Types of M odem s; The following 3G modems are supported:

44 | cellular-uplink-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Range Default usb-type <usb-type> Configures the driver type forthe 3G modem. acm, airprime, hso, option, pantech-3g,sierra-evdo, sierra- gsm,none — usb-tty <usb-tty> Spe...

Page 47 - The following example configures a cellular uplink profile:

l Huawei 3276s-150 l MC551L l Pantech UML295 l Pantech UML290 When UML290 runs in auto detect mode, the modem can switch from 4G network to 3G network or vice-versabased on the signal strength. To configure the UML290 for the 3G network only, manually set the USB type topantech-3g. To configure the ...

Page 48 - clear; Clears all ARP table information for a W-IAP.; The following command clears all information related to a W-IAP:

48 | clear Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide clear clear ap <ip-address> arp <ip-address> client <mac> datapath {session-all| statistics} Description This command clears various user-configured values from the running configuration on a W-IAP. Synta...

Page 49 - clear airgroup state statistics; This command removes the AirGroup statistics.; The following command clears AirGroup statistics:

clear airgroup state statistics clear airgroup state statistics Description This command removes the AirGroup statistics. Usage Guidelines Use this command to remove AirGroup details from the W-IAP database. Example The following command clears AirGroup statistics: (Instant AP)(config)# clear airgro...

Page 50 - Clears all certificates uploaded for the client system.; Use this command to clear the certificates from the W-IAP database.

50 | clear-cert Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide clear-cert clear-cert {ca| server} Description This command clears client and server certificates from the W-IAP database. Syntax Parameter Description ca Clears all certificates uploaded for the client system. server...

Page 51 - clock set; This command sets the date and time on the W-IAP system clock.; Numeric

clock set clock set <year> <month> <day> <time> Description This command sets the date and time on the W-IAP system clock. Syntax Parameter Description Range <year> Sets the year. Requires all 4 digits. Numeric <month> Sets the month. 1-12 <day> Sets the day...

Page 52 - recurring; The following example configures daylight saving for a timezone:

52 | clock summer-time Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide clock summer-time clock summer-time <timezone> recurring <start-week> <start-day> <start-month> <start-hour><eweek> <eday> <emonth> <ehour> no… Description ...

Page 54 - This command sets the timezone on a W-IAP.; clock timezone; Use this command to set the timezone on a W-IAP.

54 | clock timezone Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide clock timezone clock timezone <name> <hour-offset> <minute-offset> no… Description This command sets the timezone on a W-IAP. Syntax Parameter Description Range clock timezone <name> Config...

Page 55 - commit; The following command reverts the already committed changes.

commit commit {apply [no-save]| revert} Description This command allows you to commit configuration changes performed during a user session. You can also revert thechanges that are already committed. Syntax Parameter Description apply Applies and saves the W-IAP configuration changes. no-save Applie...

Page 56 - configure terminal; This command allows you to enter configuration commands.

56 | configure terminal Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide configure terminal configure terminal Description This command allows you to enter configuration commands. Syntax No parameters. Usage Guidelines Upon entering this command, the enable mode prompt changes to: ...

Page 57 - console; Allows you to enter the console configuration mode.; The following example disables console access to the W-IAP:

console console enable disable Description This command enables console access to a W-IAP through the serial port. Syntax Command/Parameter Description console Allows you to enter the console configuration mode. enable Enables console access to the W-IAP. disable Disables console access to the W-IAP...

Page 58 - Enables content filtering.; Reduce bandwidth consumption significantly.

58 | content-filtering Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide content-filtering content-filtering no… Description This command enables content filtering feature. When content filtering is enabled on an SSID, all DNS requests tonon-corporate domains on this wireless networ...

Page 59 - The following command allows you to convert a W-IAP to a remote AP:

convert-aos-ap convert-aos-ap <mode> <controller-IP> Description This command allows you to provision a W-IAP as a Campus AP or Remote AP in a controller-based network, or asa standalone AP. Syntax Parameter Description Range <mode> Provisions the W-IAP as remote AP or campus AP in...

Page 60 - copy; This command copies files to and from the W-IAP.

60 | copy Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide copy copy {config tftp <ip-address> <filename>|core-file tftp <ip-address>| flash tftp <ip-address><filename>| tftp <ip-address> <filename> {cpserver cert <password> format {p...

Page 61 - This command was modified.

Command History Version Description Dell Networking W-Series Instant6.3.1.1-4.0 This command was modified. Dell Networking W-Series Instant6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode Dell Networking W-Series Instant 6.4.0...

Page 62 - The following command disables inter-user bridging:

62 | deny-inter-user-bridging Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide deny-inter-user-bridging deny-inter-user-bridging no… Description This command disables bridging traffic between two clients of a W-IAP on the same VLAN. Bridging traffic betweenthe clients will be sent ...

Page 63 - Disables local routing of traffic.; The following command disables local routing:

deny-local-routing deny-local-routing no… Description This command disables routing traffic between two clients of a W-IAP on different VLANs. Routing traffic betweenthe clients will be sent to the upstream device to make the forwarding decision. Syntax Parameter Description deny-local-routing Disab...

Page 65 - The following example disables the default provisioning SSID:

disable-prov-ssid disable-prov-ssid no… Description This command disables the default provisioning SSID enabled in the W-IAP factory default settings. Usage Guidelines The default provisioning SSID is used during the initial configuration of the W-IAP if the automatic provisioning of theW-IAP fails ...

Page 66 - This command disconnects the clients from a W-IAP.; all

66 | disconnect-user Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide disconnect-user disconnect-user {<addr>|all|mac <mac>| network <name>} Description This command disconnects the clients from a W-IAP. Syntax Parameter Description <addr> Allows you to disc...

Page 67 - cp; Use this command to download certificates.

download-cert download-cert {ca|cp|server} <URL> Description This command allows you to download the client, authentication server, and captive portal server certificates froman FTP or TFTP server, or by using an HTTP URL. Syntax Parameter Description ca Downloads client certificates. cp Downl...

Page 68 - dpi; dpi; Dell Networking W-Series Instant; and the

68 | dpi Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide dpi dpi no… Description This command enables visualization of traffic from wired and wireless clients associated with a W-IAP. Syntax Parameter Description dpi Enables AppRF visualization. no… Removes the configuration. Usag...

Page 69 - auto; The auto option is the default and recommended setting.

dynamic-cpu-mgmt dynamic-cpu-mgmt {auto| disable| enable} Description This command enables or disables the dynamic CPU management feature, to manage resources across differentfunctions performed by a W-IAP. Syntax Parameter Description auto Configures the W-IAP to automatically enable or disable CPU...

Page 70 - The following example enables the dynamic RADIUS proxy feature:

70 | dynamic-radius-proxy Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide dynamic-radius-proxy dynamic-radius-proxy no… Description This command enables the use of IP Address of the Virtual Controller for communication with external RADIUSservers. Syntax Command/Parameter Descript...

Page 71 - This command configures a VLAN for Ethernet connections.; Configures VLAN for Ethernet ports and wired profiles; Use this command to configure VLAN for the Ethernet connections.

enet-vlan enet-vlan <vlan-ID> no… Description This command configures a VLAN for Ethernet connections. Syntax Parameter Description Range enet-vlan <vlan-ID> Configures VLAN for Ethernet ports and wired profiles 0–4093 no… Removes the configuration — Usage Guidelines Use this command to ...

Page 72 - The following command enables Eth0 bridging:

72 | enet0-bridging Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide enet0-bridging enet0-bridging Description This command allows you to use all ports on the APs as downlink ports. Usage Guidelines Use this command for W-IAP models that have only one Ethernet port enabled. When Et...

Page 73 - Assigns a wired profile to the Ethernet 0 interface port.

enet0-port-profile enet0-port-profile <profile> Description This command assigns a wired profile to the Ethernet 0 port on a W-IAP. Syntax Parameter Description enet0-port-profile <profile> Assigns a wired profile to the Ethernet 0 interface port. Usage Guidelines Use this command to ass...

Page 74 - Assigns a wired profile to the Ethernet 1 interface port.

74 | enet1-port-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide enet1-port-profile enet1-port-profile <profile> Description This command assigns a wired profile to the Ethernet 1 port on a W-IAP. Syntax Parameter Description enet1-port-profile <profile> Assigns...

Page 75 - Assigns a wired profile to the Ethernet 2 interface port.

enet2-port-profile enet2-port-profile <profile> Description This command assigns a wired profile to the Ethernet 2 port on a W-IAP. Syntax Parameter Description enet2-port-profile <profile> Assigns a wired profile to the Ethernet 2 interface port. Usage Guidelines Use this command to ass...

Page 76 - Assigns a wired profile to the Ethernet 3 interface port.

76 | enet3-port-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide enet3-port-profile enet3-port-profile <profile> Description This command assigns a wired profile to the Ethernet 3 port on a W-IAP. Syntax Parameter Description enet3-port-profile <profile> Assigns...

Page 77 - Assigns a wired profile to the Ethernet 4 interface port.

enet4-port-profile enet4-port-profile <profile> Description This command assigns a wired profile to the Ethernet 4 port on a W-IAP. Syntax Parameter Description enet4-port-profile <profile> Assigns a wired profile to the Ethernet 4 interface port. Usage Guidelines Use this command to ass...

Page 78 - Enables the users to configure additional SSIDs.

78 | extended-ssid Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide extended-ssid extended-ssid no… Description This command enables the configuration of additional WLAN SSIDs. Extended SSID is enabled by default in thefactory default settings of Instant APs. Disabling the extended...

Page 79 - Enables factory SSID configuration.; Use this command to reset a W-IAP to use the factory default SSID.

factory-ssid-enable factory-ssid-enable Description This command resets the W-IAP to use the factory configuration. Syntax Parameter Description factory-ssid-enable Enables factory SSID configuration. Usage Guidelines Use this command to reset a W-IAP to use the factory default SSID. Example The fol...

Page 80 - Disables PAN firewall.

80 | firewall-external-enforcement Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide firewall-external-enforcement firewall-external-enforcement pan disable enable ip <address> port <port> user <name> <password> no… Description This command configures externa...

Page 82 - This command configures 2.4 GHz radio channels for a specific W-IAP.; Configures the specified 2.4 GHz channel.; The following example configures the 2.4 GHz radio channel:

82 | g-channel Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide g-channel g-channel <channel> <tx-power> Description This command configures 2.4 GHz radio channels for a specific W-IAP. Syntax Parameter Description Range <channel> Configures the specified 2.4 GHz ...

Page 85 - The following example creates a GRE tunnel for the W-IAP:

gre per-ap-tunnel gre per-ap-tunnel no… Description This command configures a generic routing encapsulation (GRE) tunnel from each W-IAP to the VPN/GRE Endpointrather than the tunnels created just from the Virtual Controller. Syntax Parameter Description gre per-ap-tunnel Creates a GRE tunnel from t...

Page 86 - gre primary; This command configures a host for the primary VPN/GRE endpoint.; Use this command to configure the primary VPN/GRE host.

86 | gre primary Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide gre primary gre primary <name> no… Description This command configures a host for the primary VPN/GRE endpoint. Syntax Parameter Description gre primary <name> Specifies the fully qualified domain name (F...

Page 87 - gre type; This command configures a GRE protocol number as GRE type.

gre type gre type <type> Description This command configures a GRE protocol number as GRE type. Syntax Parameter Description Range Default gre type <type> Configures the protocol number or IP address forGRE type 16-bitprotocolnumber 0 Usage Guidelines Use this command to specify GRE type...

Page 88 - help; This command displays help for the CLI.; The following example shows the output of the help command.; Help may be requested at any point in a command by entering

88 | help Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide help help Description This command displays help for the CLI. Usage Guidelines This command displays keyboard editing commands that allow you to make corrections or changes to the commandwithout retyping. You can also enter...

Page 90 - hostname; This command changes the hostname of the Virtual Controller.; Configures a hostname for the Virtual Controller.; The following example configures host name for a W-IAP.

90 | hostname Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide hostname hostname <name> Description This command changes the hostname of the Virtual Controller. Syntax Parameter Description <name> Configures a hostname for the Virtual Controller. Usage Guidelines The ho...

Page 91 - Creates a 3GPP profile.; The following command configures a 3GPP profile:

hotspot anqp-3gpp-profile hotspot anqp-3gpp-profile <profile-name> 3gpp-plmn1…3gpp-plmn6 <PLMN-ID> enable no… Description This command configures a 3rd Generation Partnership Project (3GPP) Cellular Network for hotspots that haveroaming relationships with cellular operators. Syntax Param...

Page 93 - enable

hotspot anqp-domain-name-profile hotspot anqp-domain-name-profile <profile-name> domain-name <domain-name> enable no… Description This command defines the domain name to be sent in an Access Network Query Protocol (ANQP) informationelement in a Generic Advertisement Service (GAS) query r...

Page 97 - The following example creates an NAI realm profile:

Parameter Description Range nai-realm-name <nai-realm-name> Configures a name for the NAI realm. The realm name is oftenthe domain name of the service provider. — no… Removes any existing configuration. — Usage Guidelines Use this command to configure an NAI Realm profile that identifies and d...

Page 100 - Creates roaming consortium profile.

100 | hotspot anqp-roam-cons-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide hotspot anqp-roam-cons-profile hotspot anqp-roam-cons-profile <profile-name> enable roam-cons-oi <roam-cons-oi> roam-cons-oi-len <roam-cons-oi-len> no… Description This command c...

Page 103 - assembly

Parameter Description Range Default venue-name<name> Configures the venuename to be advertised inthe ANQP IEs. If the venuename includes spaces, thename must be enclosed inquotation marks, e.g.“Midtown ShoppingCenter”. — — venue-type<type> Specifies the venue type tobe advertised in the ...

Page 106 - Creates a connection capability profile.

106 | hotspot h2qp-conn-cap-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide hotspot h2qp-conn-cap-profile hotspot h2qp-conn-cap-profile <profile-name> enable esp-port icmp tcp-ftp tcp-http tcp-pptp-vpn tcp-ssh tcp-tls-vpn tcp-voip udp-ike2 udp-ipsec-vpn udp-voip no… ...

Page 108 - Creates an operator-friendly name profile.; The following example configures an operator friendly profile:

108 | hotspot h2qp-oper-name-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide hotspot h2qp-oper-name-profile hotspot h2qp-oper-name-profile <profile> enable op-fr-name <name> op-lang-code <language> no… Description This command configures a Hotspot 2.0 Que...

Page 111 - Creates a H2QP WAN metric profile

hotspot h2qp-wan-metrics-profile hotspot h2qp-wan-metrics-profile <profile-name> at-capacity downlink-load <load> downlink-speed <speed> enable load-duration <duration> symm-link uplink-load <load> uplink-speed <speed> wan-metrics-link-status <status> no… De...

Page 112 - The following example configures a WAN metric profile:

112 | hotspot h2qp-wan-metrics-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Range Default uplink-speed<speed> Use the uplink <speed> parameter to indicate thecurrent WAN backhaul uplink speed in Kbps. If novalue is set, this parameter w...

Page 114 - advertisement-profile

114 | hotspot hs-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Range Default Internet based on payment. Forexample, a subscription-basedInternet access in a coffee shopor a hotel offering chargeablein-room Internet access service.The corresponding i...

Page 115 - advertisement-protocol

Parameter Description Range Default h2qp-wan-metrics} l h2qp-conn-cap l h2qp-oper-class l h2qp-oper-name l h2qp-wan-metrics <profile-name> Allows you to associate a specificadvertisement profile to the hotspotprofile. — — advertisement-protocol <protocol> Configures the anqp: AccessNetwo...

Page 117 - Venue; The Hotspot 2.0 provides the following services:

Parameter Description Range Default roam-cons-oi-1 roam-cons-oi-2 roam-cons-oi-3 Configures the roaming consortiumOI to assign to one of the serviceprovider’s top three roamingpartners. This additional OI willonly be sent to a client if the addt l-roam-cons-<oisaddt l-roam-cons-ois> parameter ...

Page 118 - When a hotspot is configured in a network:; Generic Advertisem ent Service (GAS) Queries; If the client does; not; ANQP Inform ation Elem ents

118 | hotspot hs-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide l Network discovery and selection— Allows the clients to discover suitable and available networks by advertisingthe access network type, roaming consortium, and venue information through the management frames...

Page 119 - Venue G roup; Venue Types

l roam-cons-oi-3 and roam-cons-len 3 The configurable values for each additional OI include the Organization Identifier itself, the OI length, and the venuegroup and venue type associated with those OIs. Venue Types The following list describes the different venue types for each venue group: Venue G...

Page 120 - The following commands configure a hotspot profile:

120 | hotspot hs-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Venue G roup Associated Venue Type Value The associated numeric value is 6. l retail-store—The associated numeric value is 1. l grocery-market—The associated numeric value is 2. l auto-service-station—The ass...

Page 122 - Use this command to manually provision a W-IAP as a master W-IAP.

122 | iap-master Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide iap-master iap-master no… Description This command provisions a W-IAP as a master W-IAP. Syntax Command/Parameter Description iap-master Provisions the W-IAP as a master W-IAP. no… Removes the configuration. Usage Gu...

Page 123 - ids; This command configures an IDS policy for a W-IAP.

ids ids client-detection-level <type> client-protection-level <type> detect-adhoc-network detect-ap-flood detect-ap-impersonation detect-ap-spoofing detect-bad-wep detect-beacon-wrong-channel detect-block-ack-attack detect-chopchop-attack detect-client-flood detect-cts-rate-anomaly detec...

Page 125 - Enables detection of fatjack attacks.

Parameter Description Range Default detect-eap-rate-anomaly Enables Extensible AuthenticationProtocol (EAP) handshake analysis todetect an abnormal number ofauthentication procedures on a channeland generate an alarm when thiscondition is detected. — — detect-fatajack Enables detection of fatjack at...

Page 127 - bridging; You can configure the following policies:

Parameter Description Range Default bridging rogue-containment Controls Rogue APs. When rogue APsare detected, they are not automaticallydisabled. This option automatically shuts downrogue APs. When this option is enabled,clients attempting to associate to an APclassified as a rogue are disconnected...

Page 130 - Use this command to disable the automatic image check feature:; The following example disables the image check feature:

130 | ignore-image-check Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ignore-image-check ignore-image-check Description This command ignores the automatic image check feature. The automatic image check feature automaticallychecks for a new version of Instant on the image server...

Page 132 - rule

132 | inbound-firewall Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide inbound-firewall inbound-firewall rule <subnet> <smask> <dest> <mask> <match/invert> <protocol> <sport> <eport>{permit|deny|src-nat|dst-nat ip <IP-address> ...

Page 133 - deny

Command/Parameter Description Range Default NAT on packets. src-nat Allows the W-IAP to perform source NATon packets. When configured, the sourceIP changes to the outgoing interface IPaddress (implied NAT pool) or from thepool configured (manual NAT pool). — — ip <IP-addr> Specifies the destin...

Page 134 - The following example configures inbound firewall rules:

134 | inbound-firewall Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Example The following example configures inbound firewall rules: (Instant AP)(config)# inbound-firewall (Instant AP)(inbound-firewall)# rule 192.0.2.1 255.255.255.255 any any match 6 631 631 permit (Instant AP)...

Page 136 - This command configures an IP address for the W-IAP.; Use this command to assign a static IP address to the W-IAP.; The following example configures an IP address for the W-IAP.

136 | ip-address Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ip-address ip-address <ip-address> <subnet-mask> <nexthop-ip-address> <dns-ip-address> <domain-name> Description This command configures an IP address for the W-IAP. Syntax. Parameter De...

Page 137 - ip dhcp; Defines the branch ID.

ip dhcp ip dhcp <dhcp_profile> bid <bid> client-count <idx> default-router <default_router> dhcp-relay dhcp-server <dhcp_server> disable-split-tunnel dns-server <dns_server> domain-name <domain-name> exclude-address <exclude_address> host <mac> i...

Page 138 - Defines the DNS server IP address.

138 | ip dhcp Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Range Default allocated to a branch. The W-IAP doesnot allow the administrators to assignthe remaining IP addresses to anotherbranch, although a lower value isconfigured for the client count. defau...

Page 139 - Defines any of the following DHCP

Parameter Description Range Default entered in the field determines theexclusion range of the subnet. Based onthe size of the subnet, the IP addressesthat come before or after the IP addressvalue specified in this field areexcluded. ip-range <start_IP><end_IP> Defines a range of IP addre...

Page 140 - Local

140 | ip dhcp Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Range Default <server_type> assignment modes: l Dist ribut ed, L2 l Dist ribut ed, L3 l Local l Local, L3 l Cent ralized, L2 l Cent ralized, L3 distributed,l3,local,local,l3,centralized,l2,ce...

Page 141 - The following example configures a distributed,l2 DHCP scope:

controller serving the VLAN/GRE of the client. This DHCP assignment mode also allows you to add the DHCPoption 82 to the DHCP traffic forwarded to the controller. l Centralized, L3—For Centralized, L3 clients, the Virtual Controller acts as a DHCP relay agent that forwards theDHCP traffic to the DHC...

Page 142 - ip dhcp pool; This command configures a DHCP pool on the Virtual Controller.; Defines IP address of the subnet.; The following command configures a DHCP pool:

142 | ip dhcp pool Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ip dhcp pool ip dhcp pool dns-server <IP-address> domain-name <domain-name> lease-time <minutes> subnet <IP-address-subnet> subnet-mask <Subnet_Mask> no… Description This command confi...

Page 144 - l2tpv3 session; sublayer; Use this command to configure the session to carry the L2TP data.; The following example configures the L2TPv3 session:

144 | l2tpv3 session Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide l2tpv3 session l2tpv3 session <l2tpv3_session_profile> cookie len <len_of_cookie> value <cookie_val> default-l2-specific-sublayer l2tpv3 tunnel <l2tpv3_tunnel_prof_to_associate> tunnel-ip ...

Page 146 - This command configures an L2TP tunnel profile.; checksum

146 | l2tpv3 tunnel Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide l2tpv3 tunnel l2tpv3 tunnel <l2tpv3_tunnel_profile> backup peer-address <peer_IP_address_backup_tunnel> checksum failover-mode <mode> failover-retry-count <retry_count> failover-retry-inter...

Page 147 - Use this command tunnel data or traffic to L2TP Network Server (LNS).; The following example configures the L2TPv3 tunnel:; Configuration mode and L2TPV3 tunnel configuration sub-mode.

Parameter Description Range Default message-digest-type <digest_algo> Configures the messagedigest to be used to createthe MD AVP. MD5, SHA1, none MD5 mtu <MTU-size> Configures a MaximumTransmission Unit (MTU)value for the tunnel. 1—65535 1460 peer-port <peer_udp_ port> Assigns a U...

Page 148 - balancing; Use this command to configure layer-3 mobility domains on a W-IAP.; The following example configures L3-mobility:

148 | l3-mobility Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide l3-mobility l3-mobility home-agent-load-balancing virtual-controller <IP-address> subnet <IP-address-subnet> <subnet-mask> <vlan> <virtual-controller-IP-address> no... Description This ...

Page 150 - This command disables LED display on a W-IAP.; Disables LED display.; Use this command to disable the LED display.

150 | led-off Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide led-off led-off no… Description This command disables LED display on a W-IAP. Syntax Command/Parameter Description led-off Disables LED display. no… Re-enables LED display. Usage Guidelines Use this command to disable t...

Page 151 - logout; This command logs you out of the current CLI session.

logout logout Description This command logs you out of the current CLI session. Usage Guidelines Use this command to log out of the current CLI session and return to the user login prompt. Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Co...

Page 152 - Enables you to integrate the W-IAP with a Mobility Access Switch.; Use this command to integrate Mobility Access Switch with a W-IAP.

152 | mas-integration Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide mas-integration mas-integration no… Description This command enables Mobility Access Switch integration on a W-IAP. Syntax Parameter Description mas-integration Enables you to integrate the W-IAP with a Mobility...

Page 154 - mesh; This command sets up mesh network on a W-IAP.; mesh; The following example enables mesh network on a W-IAP:

154 | mesh Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide mesh mesh no… Description This command sets up mesh network on a W-IAP. Syntax Parameter Description mesh Enables mesh network on the W-IAP. no… Removes the configuration. Usage Guidelines Use this command to set up mesh n...

Page 156 - mgmt-accounting command all

156 | mgmt-accounting Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide mgmt-accounting mgmt-accounting command all no… Description This command is used to enable accounting privileges on TACACS+ servers for management users. Syntax Parameter Description mgmt-accounting command all ...

Page 157 - Configures a server for management user authentication.

mgmt-auth-server mgmt-auth-server <server> no… Description This command configures authentication servers for management user interface of the Virtual Controller. Syntax Parameter Description mgmt-auth-server <server> Configures a server for management user authentication. no… Removes th...

Page 161 - name; This command configures a unique name for the W-IAP.; Configures a name for the W-IAP or the Virtual Controller.; Use this command to configure a name for the W-IAP:

name name <name> Description This command configures a unique name for the W-IAP. Syntax Parameter Description name <name> Configures a name for the W-IAP or the Virtual Controller. Usage Guidelines Use this command to configure a name for the W-IAP: Example The following example configu...

Page 162 - This command configures NTP server for a W-IAP.; Removes the configuration; The following command configures an NTP server for a W-IAP:

162 | ntp-server Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ntp-server ntp-server <Name> no… Description This command configures NTP server for a W-IAP. Syntax Parameter Description Default ntp-server <Name> Configures the IP address or the URL (domain name) ofthe...

Page 163 - opendns; The following example configures OpenDNS credentials:

opendns opendns <user> <password> no... Description This command configures OpenDNS credentials for filtering content and to create Internet access policies that allowor deny user access to websites based on website categories and security ratings. Syntax Parameter Description opendns Co...

Page 164 - organization; Specifies the name of your organization.

164 | organization Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide organization organization <name> no… Description This command configures an organization string for W-IAPs managed or monitored by the W-AirWave Managementconsole. Syntax Parameter Description Range organizat...

Page 166 - ping; This command sends ICMP echo packets to the specified IP address.; Displays the IP address of the host.

166 | ping Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ping ping <host> Description This command sends ICMP echo packets to the specified IP address. Syntax Parameter Description <host> Displays the IP address of the host. Usage Guidelines You can send up to five I...

Page 167 - Use this command to configure PPPoE uplink profile.; Configures a user name to allow a user to log into the DSL network.; Use this command to configure PPPoE uplink connection for a W-IAP.; The following example configures the PPPoE uplink on a W-IAP:

pppoe-uplink-profile pppoe-uplink-profile <profile> pppoe-username <username> pppoe-passwd <password> pppoe-svcname <svcname> pppoe-chapsecret <password> pppoe-unnumbered-local-l3-dhcp-profile <dhcp-profile> no… Description Use this command to configure PPPoE upli...

Page 169 - proxy; This command configures HTTP proxy settings.

proxy proxy {exception <host>| server <host> <port>} Description This command configures HTTP proxy settings. Syntax Parameter Description exception<hostname> Sets the IP address or the domain name of the host to beadded under the exception list. server<hostname><por...

Page 170 - System will now restart!

170 | reload Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide reload reload <all> Description This command performs a reboot of the Virtual Controller. Syntax Parameter Description <all> Reloads all W-IAPs in a cluster. Usage Guidelines Use this command to reboot a W-IA...

Page 174 - This command configures management subnet on a W-IAP.; subnet; The following example configures a management subnet

174 | restricted-mgmt-access Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide restricted-mgmt-access restricted-mgmt-access <subnet> <mask> no… Description This command configures management subnet on a W-IAP. Syntax Parameter Description subnet Configures a management ...

Page 175 - profile

rf dot11a-radio-profile rf dot11a-radio-profile beacon-interval <interval> csa-count <count> dot11h interference-immunity <immunity-level> legacy-mode max-distance <count> spectrum-band <type> spectrum-monitor no… Description This command configures a 5.GHz or 802.11a r...

Page 176 - Use this command to create a 5.0 GHz radio profile on a W-IAP.; The following example configures the 5 GHz radio profile:

176 | rf dot11a-radio-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Range Default recommended for environments with ahigh-level of interference related to 2.4 GHzappliances such as cordless phones. l Level 4— Level 3 settings, and FIRimmunity. At th...

Page 179 - Use this command to create a 2.4 GHz radio profile on a W-IAP.; The following example configures the 2.4GHz radio profile:

Parameter Description Range Default interference related to 2.4 GHz appliancessuch as cordless phones. l Level 4— Level 3 settings, and FIRimmunity. At this level, the AP adjusts itssensitivity to in-band power, which canimprove performance in environments withhigh and constant levels of noiseinterf...

Page 181 - This command configures the radio frequency band for a W-IAP.; Use this command to configure RF band for a W-IAP.

rf-band rf-band {2.4| 5.0| all} Description This command configures the radio frequency band for a W-IAP. Syntax Parameter Description Range Default rf-band {2.4| 5.0| all} Configures a radio frequency band for a W-IAP.You can configure any of the following options: l 2.4 — For 2.4 GHz band or 802.1...

Page 182 - rft; This command is used for RF troubleshooting.; rft test profile

182 | rft Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide rft rft test profile antenna-connectivity ip-addr <IP-addr> dest-mac <MAC-addr> phy {a|g} ht-link-quality ip-addr <IP-addr> dest-mac <MAC-addr> phy {a|g} mcs <mcs> link-quality ip-addr <IP-a...

Page 183 - Privileged EXEC mode

Command Information W-IAP Platform Command Mode All platforms except W-IAP224/225,and W-IAP274/275 Privileged EXEC mode Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide rft | 183

Page 184 - route; The following example configures a routing profile:

184 | routing-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide routing-profile routing-profile route <destination> <mask> <gateway> no... Description This command configures a routing profile to define the corporate subnets, which must to be tunneled throu...

Page 185 - show 1xcert; The following example shows the output of show 1xcert command:; Default Server Certificate:

show 1xcert show 1xcert Description This command displays the details about the external server certificate, which is used by the W-IAP for clientauthentication. Usage Guidelines Use this command to view information about the server certificates uploaded to a W-IAP. Example The following example sho...

Page 186 - show about; This command displays information about Instant.; Name :Aruba Operating System Software

186 | show about Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show about show about Description This command displays information about Instant. Usage Guidelines Use this command to view information such as Instant version, build time and W-IAP model. Example The show about com...

Page 188 - This command is modified

188 | show access-rule Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ---- ---------------------- - ----- ------- ------------- Vlan Id :0 ACL Captive Portal:disable ACL ECP Profile :default CALEA :disable Bandwidth Limit :upstream disable The output of this command displays info...

Page 189 - The output of this command includes the following parameters:

show access-rule-all show access-rule-all Description This command displays the details of the access rules configured for all wired and wireless profiles on the W-IAP. Usage Guidelines Use this command to view information access rules configured for all wired and wireless profiles on the W-IAP. Exa...

Page 190 - Access Rule Name

190 | show access-rule-all Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Access Rule Name Displays the name of the access rule. In use Indicates if the access rules are in use. Access Rules Displays the access rules parameter for each rule configured for th...

Page 191 - show airgroup; debug statistics

show airgroup show airgroup {blocked-queries [dlna| mdns]| blocked-service-id [dlna| mdns]| cache {<MAC-address> | entries [dlna| mdns]} | cppm {auth server [coa-capable | non-coa-only] | entries |query-interval | server}| cppm-entry <MAC-address> | debug statistics| internal-statestatis...

Page 192 - The output of this command includes the following information:; show airgroup cppm auth server non-coa-only

192 | show airgroup Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show airgroup blocked-queries The show airgroup blocked-queries command output displays the blocked queries if any: AirGroup dropped Query IDs -------------------------- Service ID #query-hits ---------- ---------...

Page 193 - The output of these commands provide the following information:; show airgroup cppm entries; The output of this command provides the following information:

All Airgroup Non-CoA-only Servers known to MDNS ----------------------------------------------- Server IP-Address Port timeout rfc3576 rfc3576-only rfc3576-port ------ ---------- ---- ------- ------- ------------ ------------ test 192.0.2.0 1812 5 Disabled Disabled 5999 test123 192.0.2.1 1812 5 Disa...

Page 194 - show airgroup debug statistics

194 | show airgroup Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Column Description swarm id Indicates the cluster ID of the W-IAP. ap id Displays the MAC address of the W-IAP on which AirGroup is configured. ap ip Displays the IP address of the W-IAP on which AirGroup is confi...

Page 195 - Indicates the AirGroup configuration status on the slave W-IAP.; show airgroup internal-state statistics

mdns apdb init counter 7(7) mdns apdb destroy counter 1(1) user timed out 1(1) airgroup restore count 1(1) mdns mac move counter 4(4) mdns master to vc hello rx 2060(2060) mdns slave to slave hello rx 8240(8240) mdns ap to ap mac sync resp rx 57(57) mdns master to vc mac req rx 1580(1580) swarm upda...

Page 196 - show airgroup servers

196 | show airgroup Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Query - resp pkt gen & send 0 0 0 0 Query - Response packet send 0 0 0 0 Query 0 0 0 0 Internal DLNA Statistics ------------------------ Functionality Hit Count Since Last Read Hit Count Total Average Time in ...

Page 197 - show airgroup status; Indicates if the inter cluster mobility is enabled.

show airgroup status The following output is displayed for the show airgroup status command: AirGroup Feature ---------------- Status ------ Disabled AirGroup- MDNS Feature ---------------------- Status ------ Disabled AirGroup- DLNA Feature ---------------------- Status ------ Disabled AirGroup Mul...

Page 198 - Indicates if a guest VLAN is used for Bonjour services.; show airgroup swarm -info; Indicates the MAC address of the AirGroup clients.

198 | show airgroup Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Column Description AirGroup Guest Multicast Indicates if a guest VLAN is used for Bonjour services. CPPM Parameters Displays CPPM configuration parameters associated with the AirGroupconfiguration. AirGroup Servic...

Page 199 - Role

Column Description Wired/Wireless Displays if the AirGroup user is connected to a wired or wireless interface. Role Indicates the AirGroup user role. Username Displays the username of the AirGroup user. AP-Mac Displays the MAC address of the W-IAP to which the user is connected. Query/Resp Displays ...

Page 200 - show airgroupservice; AirGroupService Details

200 | show airgroupservice Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show airgroupservice show airgroupservice [disallow {role| vlan}] Description This command displays the AirGroup service configuration details for a W-IAP. Syntax Parameter Description show airgroupservice ...

Page 203 - show airgroupservice-ids; service

show airgroupservice-ids show airgroupservice-ids <service> Description This command displays the AirGroup service IDs configured on a W-IAP for its AirGroup clients. Syntax Parameter Description service Indicates the name of the service and displays the service ID details of specifiedAirGroup...

Page 204 - show acl; domains; Use this command to view the ACL configuration details.

204 | show acl Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show acl show acl {domains} Description This command displays the Access Control List (ACL) configuration details. Syntax Parameter Description domains Displays the domains configured with an access control list. Usage...

Page 205 - show ale; This command displays the ALE configuration details.; Displays the ALE configuration details.; Use this command to view the ALE configuration status.

show ale show ale {config| status} Description This command displays the ALE configuration details. Syntax Parameter Description config Displays the ALE configuration details. status Displays the status of ALE server. Usage Guidelines Use this command to view the ALE configuration status. Example Th...

Page 207 - show alert global; This command displays the list of client alerts for a W-IAP.

show alert global show alert global [count] Description This command displays the list of client alerts for a W-IAP. Syntax Parameter Description <count> Filters client alerts based on the specified number. Usage Guidelines Use this command to view the client alerts for a W-IAP. The client ale...

Page 208 - show alg; The following output is displayed for the show alg command:

208 | show alg Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show alg show alg Description This command displays the Application Layer Gateway (ALG) protocol information configured on a W-IAP. Usage Guidelines Use this command to view configuration details for the ALG protocols....

Page 209 - Use this command to view the W-IAP whitelist.; Allow New APs :enable; Allow New APs

show allowed-aps show allowed-aps Description This command displays the list of W-IAPs that are allowed to join the W-IAP cluster. Usage Guidelines Use this command to view the W-IAP whitelist. Example The following example shows the output of the show allowed-aps command: Allow New APs :enable AP W...

Page 210 - show all monitor; Swarm Active Laser Beam Sources

210 | show all monitor Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show all monitor show all monitor active-laser-beams Description This command shows information for Dell Networking W-Series Instant Air Monitors. Usage Guidelines Use this command to view the information on De...

Page 211 - Use this command to view the AMP related configurations.

show amp-audit show amp-audit Description This command displays the set of configurations on the W-AirWave Management Platform. Usage Guidelines Use this command to view the AMP related configurations. Example The following example shows the output of the show amp-audit command: rule any any match a...

Page 215 - The following output is displayed for the show ap-env command:; Antenna Type:Internal

show ap-env show ap-env Description This command displays all provisioned AP parameters such as the type of antenna used by a. The output of thiscommand also indicates if the W-IAP is provisioned as a master W-IAP. Usage Guidelines Use this command to view the antenna configuration details for a W-I...

Page 216 - show aps; Displays the list of all active W-IAPs in the cluster.; The following output is displayed for the show aps command:; Indicates if spectrum monitoring is enabled or disabled.

216 | show aps Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show aps show aps [scanning][sync] Description This command displays all active W-IAPs, W-IAP scanning, and synchronization status. Syntax Parameter Description aps Displays the list of all active W-IAPs in the cluster...

Page 218 - Indicates if the W-IAP is serving as master or slave.

218 | show aps Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide AP Sync List ------------ MAC IP Address Class Current Version --- ---------- ----- --------------- The output of this command includes the following parameters: Column Description MAC Indicates MAC address of the W-IA...

Page 219 - show ap allowed-channels; This command displays a list of allowed channels for a W-IAP.; PHY Type Allowed Channels; PHY Type

show ap allowed-channels show ap allowed-channels <country-code> Description This command displays a list of allowed channels for a W-IAP. Syntax Parameter Description <country-code> Specify a country code to display allowed channels for that country. Usage Guidelines Specify the country...

Page 221 - Displays the EIRP settings allowed for a specific country.

show ap allowed-max-EIRP show ap allowed-max-EIRP [<country>] Description This command displays the maximum EIRP settings for the country in which the W-IAP is currently operational. Youcan also view the maximum EIRP settings for a specific country. Syntax Parameter Description [<country>...

Page 222 - show ap arm; Displays ARM bandwidth details for a W-IAP.; show ap arm bandwidth-m anagem ent

222 | show ap arm Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap arm show ap arm {bandwidth-management | history | neighbors |rf-summary | scan-times} Description This command displays information about bandwidth management, historical statistics, W-IAP neighbors, RFsumma...

Page 223 - Client; show ap arm history; ARM History

Column Description Client Displays the list of W-IAP clients connected through the Wi-Fi interface. Tx Pkt Displays the transmission packet details associated with the interface. Tx Byte Displays the number of bytes in the transmission packets associated with theinterface. Tx Alloc (ms) Indicates th...

Page 224 - Displays the channel number used by the W-IAP before the ARM change.

224 | show ap arm Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide 2013-05-10 09:04:24 149+ 157+ 27 27 I 2013-05-10 06:08:59 157+ 149+ 27 27 I 2013-05-10 05:55:10 153- 157+ 27 27 I 2013-05-10 05:11:21 157+ 153- 27 27 I Interface :wifi1 ARM History ----------- Time of Change Old Cha...

Page 225 - show ap arm neighbors; show ap arm rf-sum m ary

show ap arm neighbors The show ap arm neighbors command displays the ARM settings on the W-IAP neighbors. The following exampleshows the output of the show ap arm neighbors command: ARM Neighbors ------------- bssid essid channel rssi tx-power PL (dB) AP Flags Last Update ----- ----- ------- ---- --...

Page 226 - Displays the list of channels enabled on a W-IAP.

226 | show ap arm Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide 60 0 0 0 93 0/0/0/0/94 0/0(0) 29/14//0/0(43) 64 0 0 0 93 6/0/0/0/94 0/0(0) 43/10//0/0(53) 149 0 0 0 93 3/2/0/0/99 0/0(0) 113/41//0/0(154) 153 0 0 2 93 23/23/0/1/100 0/0(0) 124/68//0/0(192) 157 0 0 0 93 2/1/0/1/94 0/...

Page 227 - detected by the neighboring APs on that channel.; show ap arm scan-tim es

Column Description detected by the neighboring APs on that channel. intf_idx(Total Displays channel interference details. The W-IAP uses this metric to measure co-channel and adjacent channel interference. The Interference Index is calculatedas a/b//c/d, where: l Metric value “a” is the channel inte...

Page 228 - WIF Scanning State; channel

228 | show ap arm Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide 149 68631720 952 0 0 DVACFT 172074 153 32278480 1268 0 0 DVACPT 172088 157 38634770 1207 0 0 DVACFT 172132 161 20620710 1361 0 0 DVACPT 172161 165 170280 1548 0 0 DVACT 172110 1 86424330 903 0 0 DVACFT 172161 2 5357...

Page 230 - show ap association; Indicates the Name of a W-IAP or the AP group.

230 | show ap association Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap association show ap association Description This command displays the association table for an AP group or for an individual W-IAP. Usage Guidelines Use this command to view information about the cli...

Page 231 - num assoc

Column Description tunnel-id Indicates the identification number of the W-IAP tunnel. assoc. time Indicates the amount of time the client has been associated with the W-IAP, in thehours:minutes:seconds format. num assoc Indicates the number of clients associated with the W-IAP. flags Displays flags ...

Page 232 - Displays the IP address of an AP.

232 | show ap bss-table Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap bss-table show ap bss-table Description This command displays an AP’s Basic Service Set (BSS). Usage Guidelines The output of the show ap bss-table command shows the Dell AP BSS table for all APs. To f...

Page 233 - cur

Column Description ch/EIRP/max-EIRP Displays the radio channel used by the AP/current effective Isotropic Radiated Power(EIRP) /maximum EIRP. cur Displays the current number of clients on the AP. Command History Version Description Dell Networking W-Series Instant6.2.1.0-3.3 This command is introduc...

Page 237 - This command displays the client probe report for a W-IAP.; AP Client Probe Report for Wifi0

show ap client-probe-report show ap client-probe-report [<radio>] Description This command displays the client probe report for a W-IAP. Syntax Parameter Description <radio> Allows you to filter the output based the ID number of the radio (for example, 0 or1). Usage Guidelines Use this c...

Page 238 - Total 74 Stations

238 | show ap client-probe-report Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide 00:21:6a:ba:b7:ce 31 No 2s 04:0c:ce:e1:98:78 50 No 8h:3m:27s 00:1e:65:71:18:de 8 No 53m:14s 60:67:20:4d:e8:a8 13 No 2h:8m:22s b4:b6:76:42:49:56 41 No 14s b4:b6:76:42:49:1f 34 No 25s c4:85:08:d4:79:48...

Page 239 - Last Refused Clients Table

show ap client-match-refused show ap client-match-refused [<radio>] Description This command displays the list of clients for which the channel allocation is refused based on the client matchconfiguration parameters. Syntax Parameter Description <radio> Allows you to filter the output ba...

Page 241 - Dynamic Load Balancing:; Client Match Triggers

show ap client-match-triggers show ap client-match-triggers Description This command displays the configuration conditions that trigger client match events and actions for the clientsassociated with a W-IAP. Usage Guidelines Use this command to view the clients match trigger records. When the client...

Page 243 - Client Match Neighbor Table

show ap client-view show ap client-view Description This command displays information about the clients in the AP neighborhood. Usage Guidelines Use this command to view information about the clients associated with the neighboring W-IAPs. Example The following example shows the output of show ap cl...

Page 245 - show ap debug airwave; The following example shows the output of show ap airwave command:; Displays the IP address or domain name of the W-AirWave server.; The Domain name is added.

show ap debug airwave show ap debug airwave Description This command displays the list of W-AirWave servers configured on a W-IAP. Usage Guidelines Use this command to view the list of W-AirWave servers configured for a W-IAP. Example The following example shows the output of show ap airwave command...

Page 246 - No configuration received from AirWave yet

246 | show ap debug airwave-config-received Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug airwave-config-received show ap debug airwave-config-received Description This command indicates if any configuration information is received by the W-IAP from the W-AirWave s...

Page 248 - This command displays the pending W-AirWave server events.; Use this command to view the pending W-AirWave server events.

248 | show ap debug airwave-events-pending Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug airwave-events-pending show ap debug airwave-events-pending Description This command displays the pending W-AirWave server events. Usage Guidelines Use this command to view the...

Page 250 - show ap debug airwave-state

250 | show ap debug airwave-state Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug airwave-state show ap debug airwave-state Description This command displays the configuration details and status of W-AirWave events associated with a W-IAP. Usage Guidelines Use this c...

Page 252 - show ap debug airwave-stats

252 | show ap debug airwave-stats Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug airwave-stats show ap debug airwave-stats Description This command displays the configuration statistics associated with a W-IAP managed or monitored by the W-AirWave server. Usage Guid...

Page 253 - show ap debug am-config; MAC address in the trace buffer.

show ap debug am-config show ap debug am-config Description This command displays the information required for debugging a W-IAP. Syntax Parameter Description mac MAC address in the trace buffer. Example The following example shows the partial output of show ap debug am-config command: Channel Numbe...

Page 255 - Auth Trace Buffer

show ap debug auth-trace-buf show ap debug auth-trace-buf [<Mac>] Description This command displays the trace buffer for authentication events associated with the W-IAP. Syntax Parameter Description <Mac> Displays the authentication trace information for a specific MACaddress. Usage Guid...

Page 257 - show ap debug client-match

show ap debug client-match show ap debug client-match <radio> Description This command displays the information about the client match configuration status on an AP radio interface. Syntax Parameter Description <radio> Allows you to specify the ID number of the radio (for example, 0 or 1...

Page 258 - show ap debug client-stats; This command displays detailed statistics about a W-IAP client.; Displays data based on the client MAC address.; Use this command to view information about a W-IAP client.

258 | show ap debug client-stats Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug client-stats show ap debug client-stats <mac) Description This command displays detailed statistics about a W-IAP client. Syntax Parameter Description <mac> Displays data based ...

Page 260 - Shows the number of frames received.

260 | show ap debug client-stats Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Last SNR CTL0 Indicates the signal-to-noise ratio for the last received data packet on the primary(control) channel 0. This parameter is only displayed for APs operating in 40 MH...

Page 262 - show ap debug client-table; This command shows the clients associated with a W-IAP.; Use this command to view a list of W-IAP clients.

262 | show ap debug client-table Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug client-table show ap debug client-table Description This command shows the clients associated with a W-IAP. Usage Guidelines Use this command to view a list of W-IAP clients. Example The...

Page 263 - UAPSD

Parameter Description UAPSD Shows the following values for Unscheduled Automatic Power Save Delivery (UAPSD) incomma-separated format: VO, VI, BK, BE, Max SP, Q Len. l VO: If 1, UAPSD is enabled for the VoIP access category. If UAPSD is disabled forthis access category, this value is 0. l VI: If 1, ...

Page 264 - show ap debug crash-info; No parameters

264 | show ap debug crash-info Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug crash-info show ap debug crash-info Description This command displays log information for a W-IAP that crashed. The stored crash information is cleared from theflash after the W-IAP reboot...

Page 265 - show ap debug dhcp-packets

show ap debug dhcp-packets show ap debug dhcp-packets Description This command displays information about the DHCP packets sent or received by a W-IAP. Usage Guidelines Use this command to view information about the DHCP packets trace information for a W-IAP. Example The following example shows the ...

Page 266 - show ap debug dot1x-statistics

266 | show ap debug dot1x-statistics Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug dot1x-statistics show ap debug dot1x-statistics Description This command displays the aggregate 802.11X debug statistics for a W-IAP. Usage Guidelines Use this command to view inform...

Page 268 - show ap debug driver-config; This command displays W-IAP driver configuration.

268 | show ap debug driver-config Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug driver-config show ap debug driver-config Description This command displays W-IAP driver configuration. Usage Guidelines Use this command to review configuration changes made since the ...

Page 271 - show ap debug mgmt-frames

show ap debug mgmt-frames show ap debug mgmt-frames <mac> Description This command displays the trace information for the 802.11 management frames. Syntax Parameter Description <mac> Displays trace information for a W-IAP based on MAC address. Example The following example shows the part...

Page 273 - show ap debug persistent-clients

show ap debug persistent-clients show ap debug persistent-clients Description This command displays the information about the persistent W-IAP clients. Usage Guidelines Use this command to view information about the clients that are persistently connected to a W-IAP. Example The following example sh...

Page 274 - show ap debug radio-stats; Use this command to view the radio debug statistics for a W-IAP.

274 | show ap debug radio-stats Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug radio-stats show ap debug radio-stats [<radio-ID>] Description This command displays the aggregate radio debug statistics of a W-IAP. Syntax Parameter Description <radio-ID> A...

Page 275 - Displays the transmission and reception parameters.

Tx Data Bytes 108 Mbps (Mon) 0 RADIO Stats ----------- Parameter Value --------- ----- Tx Data Bytes 108 Mbps+ (Mon) 0 Tx 6 Mbps 557650 Tx WMM [BE] 125 Tx WMM [VO] 557532 Tx WMM [BE] Dropped 158561 Tx UAPSD OverflowDrop 0 TX Timeouts 36 Lost Carrier Events 8 Tx HT40 Hang Detected 0 Tx HT40 Hang Stuc...

Page 277 - show ap debug radius-statistics; Use this command to view the authentication server details.

show ap debug radius-statistics show ap debug radius-statistics Description This command displays the RADIUS statistics for the authentication servers configured on a W-IAP. Usage Guidelines Use this command to view the authentication server details. Example The output of this command displays gener...

Page 278 - show ap debug shaping-table

278 | show ap debug shaping-table Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug shaping-table show ap debug shaping-table Description This command displays the shaping information for clients associated to a W-IAP. Usage Guidelines Use this command to view the shap...

Page 279 - in

Column Description last-t Shows the number of tokens that were allocated to the station last time tokenallocation algorithm ran. in Shows the number of packets received. out Shows the number of packets sent. drop Shows the number of dropped packets. q Shows the number of queued packets tx-t Shows th...

Page 280 - show ap debug spanning-tree

280 | show ap debug spanning-tree Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug spanning-tree show ap debug spanning-tree Description This command displays the Spanning Tree Protocol (STP) information for a W-IAP. Usage Guidelines Use this command to view STP detai...

Page 281 - show ap debug stm-config; Column

show ap debug stm-config show ap debug stm-config Description This command displays the W-IAP station management configuration information. Usage Guidelines Use this command to view the details of station management configuration. Example The following output is displayed for the show ap debug stm-c...

Page 282 - show ap debug system-status

282 | show ap debug system-status Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap debug system-status show ap debug system-status Description This command displays the detailed system configuration information for a W-IAP. Usage Guidelines Use this command under the guidan...

Page 283 - Client 11k Beacon Report

show ap dot11k-beacon-report show ap dot11k-beacon-report <mac> Description This command displays the beacon report details for the 802.11k clients of a W-IAP. Syntax Parameter Description <mac> Allows you to specify the MAC address of the client for which you want to view thebeacon repo...

Page 286 - show ap mesh counters; This command displays the mesh counters for a W-IAP.

286 | show ap mesh counters Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap mesh counters show ap mesh counter Description This command displays the mesh counters for a W-IAP. Usage Guidelines Use this command to view a list of mesh counters available for a W-IAP. Example ...

Page 288 - show ap mesh link; This command shows the mesh link of the W-IAP.; MAC address of the mesh node.

288 | show ap mesh link Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap mesh link show ap mesh link Description This command shows the mesh link of the W-IAP. Example The following example shows the output of show ap mesh link command: (Instant AP)# show ap mesh link Neigh...

Page 289 - Flags

Parameter Description and the amount of time that relationship has existed. l P = Parent l C = Child l N = Neighbor l B = Blacklisted-neighbor Flags This parameter shows additional information about the mesh neighbor. The keydescribing each flag is displayed at the bottom of the neighbor list. RSSI ...

Page 290 - show ap mesh neighbors; This command shows all mesh neighbors for an AP.

290 | show ap mesh neighbors Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap mesh neighbors show ap mesh neighbors Description This command shows all mesh neighbors for an AP. Example The following example shows the output of show ap mesh neighbors command: Neighbor list -...

Page 292 - show ap monitor; This command shows information for W-IAP Air Monitors.

292 | show ap monitor Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap monitor show ap monitor {active-laser-beams|ap-list|ap-wired-mac <mac>|arp-cache| containment-info |enet-wired-mac <mac> | ids-state <type> | pot-ap-list | pot-sta-list | routers | scan...

Page 293 - tot-beacons: Total number of beacons seen since the last reset.; Examples; show ap m onitor ap-list

Parameter Description l num-beacons: Number of beacons seen during a 10-second scan l tot-beacons: Total number of beacons seen since the last reset. l num-frames: Total number of frames seen since the last rest. l mt: Monitor time; the number of timer ticks elapsed since the first AP isrecognized. ...

Page 295 - show ap m onitor ids-state

show ap m onitor ids-state Use this command to view information about the Intrusion Detection System (IDS) the following detection polices: l Detect Block ACK DOS l Disconnect station attack l Intrusion event Type l Intrusion rate parameters l Detect Omerta attack l Detect Power Save DOS Attack l De...

Page 298 - show ap m onitor status

298 | show ap monitor Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide average 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 high 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 low 40 40 40 40 40 40 40 40 40 40 40 40 40 40 40 count 110 638 638 638 638 638 649 649 638 638 429 649 638 5...

Page 299 - The outputs of the AP monitor command displays the following:

oui --- RTLS Configuration and State ----------------------------- Type Server IP Port Freq Active Rpt-Tags Tag-Mcast-Addr Tags-Sent Rpt-Sta Incl-Unassoc-StaSta-Sent Cmpd-Msgs-Sent ---- --------- ---- ---- ------ -------- -------------- --------- ------- ---------------- -------- -------------- MMS ...

Page 300 - show ap pmkcache

300 | show ap pmkcache Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ap pmkcache show ap pmkcache Description This command displays the pairwise master key (PMK) cache table for clients associated with the W-IAP. Usage Guidelines Use this command to view PMK cache table con...

Page 303 - The following example shows the output of show ap-alert command.

show ap-alert show ap-alert <count> Description This command displays all the alerts received for the specified APs. Usage Guidelines Use this command to check all the alerts received for all the APs specified. Example The following example shows the output of show ap-alert command. AP Alerts ...

Page 304 - Application Service

304 | show app-services Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show app-services show app-services Description This command displays the list of application services available on a W-IAP. Usage Guidelines Use this command to view the list of application services available...

Page 305 - Name

smtp 6 25 25 snmp 17 161 161 snmp-trap 17 162 162 ssh 6 22 22 svp 119 0 65535 syslog 17 514 514 telnet 6 23 23 tftp 17 69 69 vocera 17 5002 5002 The output of this command provides the following information: Parameter Description Name Indicates the list of application services available on a W-IAP. ...

Page 306 - Use this command to view the channel details configured on a W-IAP.

306 | show arm-channels Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show arm-channels show arm-channels Description This command displays the ARM channel details configured on a W-IAP. Usage Guidelines Use this command to view the channel details configured on a W-IAP. Example...

Page 307 - Channel

157+ enable The output of this command provides the following information: Parameter Description Channel Displays the list of channels available in the 2.4 GHz and 5 GHz bands. Status Indicates if the channels in the 2.4 GHz and 5 GHz bands are enabled ordisabled. Command History Version Description...

Page 308 - show arm config; This command displays the ARM configuration details for a W-IAP.; Use this command to view the ARM configuration details for a W-IAP.; The following example shows the output of show arm config command:

308 | show arm config Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show arm config show arm config Description This command displays the ARM configuration details for a W-IAP. Usage Guidelines Use this command to view the ARM configuration details for a W-IAP. Example The follo...

Page 311 - show arp; The following example shows the output of show arp command

show arp show arp Description This command displays the Address Resolution Protocol (ARP) entries for the Virtual Controller. Usage Guidelines Use this command to view the ARM messages sent or received by the Virtual Controller. Example The following example shows the output of show arp command IP a...

Page 312 - show attack; Displays attack counters.

312 | show attack Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show attack show attack {config| stats} Description This command displays information about firewall settings configured on a W-IAP to protect the network againstwired attacks such as ARP attacks or malformed DHCP p...

Page 314 - show auth-survivability; Auth Survivability time out :24; UserName

314 | show auth-survivability Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show auth-survivability show auth-survivability {cached-info| debug-log [<count>]| time-out} Description This command displays the authentication survivability information for a W-IAP. Syntax Comma...

Page 318 - show blacklist-client

318 | show blacklist-client Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show blacklist-client show blacklist-client [config] Description This command shows the configuration details for blacklisting clients and lists the clients blacklisted by W-IAP. Syntax Parameter Descripti...

Page 319 - Manually Blacklisted clients

Parameter Description Manually Blacklisted clients Displays the details of clients that are blacklisted manually. Dynamically Blacklisted Clients Displays the list of clients that dynamically blacklisted due to multipleauthentication rules or an ACL rule trigger. Command History Version Description ...

Page 320 - show calea config; Use this command to CALEA configuration details.

320 | show calea config Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show calea config show calea config Description This command displays the details configured for CALEA server integration on a W-IAP. Usage Guidelines Use this command to CALEA configuration details. Example T...

Page 321 - show calea statistics

show calea statistics show calea statistics Description This command displays the tunnel encapsulation statistics for a W-IAP. Usage Guidelines Use this command to view the GRE encapsulation statistics for the W-IAPs with CALEA server integration featureenabled. Example The following example shows t...

Page 322 - Displays decoded texts.

322 | show captive-portal Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show captive-portal show captive-portal Description This command shows the external and internal captive portal parameters configured for a network profile. Usage Guidelines Use this command to view informat...

Page 323 - Server

Parameter Description Server Displays the external Captive port server. URL Displays the URL of the external captive portal splash page server. Authentication Text Indicates if the external captive portal user authentication issuccessful. Port Displays the port used for communicating with the extern...

Page 324 - Internal Captive Portal Domain:

324 | show captive-portal-domains Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show captive-portal-domains show captive-portal-domains Description This command displays the internal and external captive portal server domains. Usage Guidelines Use this command to view informatio...

Page 325 - show cellular; Displays the status of the cellular configuration for the W-IAP

show cellular show cellular {config | status} Description These commands display the status and cellular configuration of the W-IAP. Syntax Parameter Description show cellular config Displays the cellular configuration details available for the W-IAP show cellular status Displays the status of the c...

Page 326 - Lists the countries that support cellular deployment.

326 | show cellular Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide US Canada Supported ISP list ------------------ ISP list -------- Cincinnati Bell Virgin Telecom Telenor Vodafone/SmarTone O2 SFR Orange 3/HUTCH Optus SingTel HKCSL/1010 Verizon ICE Reliance NetConnect+ Tata Indic...

Page 327 - Card

---- ------ ---- Not-present Not-detect Linkdown The output of this command includes the following parameters: Parameters Description Card Indicates if the cellular cards are currently configured on the W-IAP. detect Indicates if cellular modems are detected on the W-IAP Link Indicates the current s...

Page 328 - show cert all; The following example shows the output of show cert command:

328 | show cert all Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show cert all show cert all Description This command displays the details about the certificates uploaded on a W-IAP. Usage Guidelines Use this command to view information about the certificates uploaded to a W-IA...

Page 329 - show clients; This command displays details about the W-IAP clients.; Filters checksum errors for a specific client MAC address.; show clients and show clients wired; The following output is displayed for the show clients command:; Client List; A similar output is displayed for the show clients wired command.

Page 333 - show clock; timezone all; show clock tim ezone all; Support Timezones

show clock show clock [summer-time| timezone all] Description This command displays the system clock, current timezone, and the daylight saving time configured on a W-IAP Syntax Parameter Description summer-time Displays the summer (daylight saving) time settings. timezone all Displays the configure...

Page 334 - show clock sum m er-tim e; Related Commands

334 | show clock Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Country Displays the country name. Timezone Displays the name of the timezone. DST Name Displays the name of the Daylight Saving Time. DST Recurring Displays the name of the Daylight Saving recu...

Page 336 - show configuration; This command displays the configuration saved on the W-IAP.

336 | show configuration Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show configuration show configuration Description This command displays the configuration saved on the W-IAP. Usage Guidelines Use this command to view the entire configuration saved on the W-IAP, including a...

Page 340 - Config Status

340 | show config-status Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show config-status show config-status Description This command displays the details about the configuration status of a W-IAP. Usage Guidelines Use this command to view the current configuration status of the...

Page 341 - show console-settings; Console Setting

show console-settings show console-settings Description This command displays the details about the console settings of a W-IAP. Usage Guidelines Use this command to view if the access to W-IAP console is enabled or disabled. Example The following example shows the output of the show console-setting...

Page 342 - Use this command to view a list of W-IAP country codes.; AE:United Arab Emirates

342 | show country-codes Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show country-codes show country-codes Description This command shows the country code for the W-IAP. The country code specifies allowed channels for that country. Usage Guidelines Use this command to view a l...

Page 345 - show cpcert

show cpcert show 1xcert Description This command displays the details of the captive portal server certificate, which is used by the W-IAP for guestauthentication. Usage Guidelines Use this command to view information about the captive portal server certificate uploaded on W-IAP. Example The followi...

Page 346 - show cpu; This command displays the CPU details.; The following example shows the output of show cpu command:; PID USER STATUS RSS PPID %CPU %MEM COMMAND

346 | show cpu Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show cpu show cpu [details] Description This command displays the CPU details. Syntax Parameter Description [details] Include this optional parameter at the request of Dell technical support todisplay additional CPU tr...

Page 348 - show datapath; Descriptions; This command shows the system statistics for your W-IAP.; show datapath acl

348 | show datapath Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show datapath show datapath {acl <ID>|acl-all|acl-allocation|acl-rule <rule>|acl-rule-detail<acl>|bridge|dmo-session|dmo-station <mac>|mcast|nat-pool <ID>|routesession|statistics|user...

Page 349 - Datapath ACL 3 Entries; show datapath acl-all; ACL ACE Start ACE Block Size

Datapath ACL 3 Entries ----------------------- Flags: P - permit, L - log, E - established, M/e - MAC/etype filter S - SNAT, D - DNAT, R - redirect, r - reverse redirect m - Mirror I - Invert SA, i - Invert DA, H - high prio, O - set prio, C - Classify Media A - Disable Scanning, B - black list, T -...

Page 350 - show datapath acl-rule; Datapath SSID: test ACL Entries

350 | show datapath Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide ---- ---------- --------------- 105 3200 32 103 3234 16 107 3250 32 104 3282 16 108 3298 32 100 3330 2 101 3332 4 102 3336 4 134 3340 4 135 3344 8 136 3352 4 143 3360 8 145 3372 8 130 3380 16 131 3412 16 132 3444 ...

Page 354 - show datapath user; Datapath User Table Entries; show datapath vlan; Datapath VLAN Table Entries

354 | show datapath Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show datapath user The following example shows the partial output of show datapath user command. Datapath User Table Entries --------------------------- Flags: P - Permanent, W - WEP, T- TKIP, A - AESCCM R - Proxy...

Page 356 - show delta-config cfgid

356 | show delta-config Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show delta-config show delta-config cfgid Description This command displays the difference between the current configuration in the current CLI session and theconfiguration that is saved on the W-IAP. Usage Gu...

Page 357 - show derivation-rules

show derivation-rules show derivation-rules Description This command displays the list of role and VLAN derivation rules configured for the WLAN SSIDs and wired profilesin a W-IAP. Usage Guidelines Use this command to view the derivation rules configured for a network profile. Example The following ...

Page 358 - filterwin2k

358 | show dhcp-allocation Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show dhcp-allocation show dhcp-allocation Description This command displays information about the DHCP address allocation. Usage Guidelines Use this command to view DHCP address allocation for network addre...

Page 359 - This command displays the DHCP options configured on a W-IAP.; The following output is displayed for the show dhcpc-opts command:; Not available

show dhcpc-opts show dhcpc-opts Description This command displays the DHCP options configured on a W-IAP. Usage Guidelines Use this command to view the current status of the vendor-specific DHCP options configured on a W-IAP. TheDHCP options are configured and enabled for assignment and distribution...

Page 360 - show dhcps config; The output of this command displays the following information:; Displays the name of the DHCP scope.

360 | show dhcps config Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show dhcps config show dhcps config Description This command provides information about the DHCP scopes configured for a W-IAP. Usage Guidelines Use this command to view configuration details associated with t...

Page 363 - show dhcp subnets

show dhcp subnets show dhcp subnets Description This command displays the subnet details and the gateway IP for distributed L2 and L3 networks. Usage Guidelines Use this command to view the subnet details for the distributed,l2 and l3 networks. Example The following example shows the output of the s...

Page 364 - type; Branch Count Table; Client Count Upto

364 | show distributed-dhcp-branch-counts Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show distributed-dhcp-branch-counts show distributed-dhcp-branch-counts <type> <sip> <eip> Description This command displays the branch count for the distributed DHCP scopes...

Page 367 - show dpi; This command displays the DPI configuration information.; Use this command to view the DPI configuration details.; show dpi app; Pre-defined Application; show dpi appcategory; Pre-defined Application Categories

show dpi show dpi {app <name> all|appcategory <name> all|debug statistics|qsessions [detail [<session_id>]]|webcategory <name> all|webcategory-lookup <url>} Description This command displays the DPI configuration information. Syntax Command/Parameter Description app <...

Page 368 - The output of this command displays all application categories.; show dpi debug statistics

368 | show dpi Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Name App Category ID ---- --------------- antivirus 1 authentication 2 cloud-file-storage 3 collaboration 4 encrypted 5 enterprise-apps 6 gaming 7 im-file-transfer 8 instant-messaging 9 mail-protocols 10 mobile-app-sto...

Page 369 - show dpi webcategory

current minor version :1 show dpi webcategory The following example shows the output of the show dpi webcategory all command: (Instant AP)# show dpi webcategory all Pre-defined BrightCloud Web Categories -------------------------------------- Name Web Category ID ---- --------------- real-estate 1 c...

Page 370 - show dpi webcategory-lookup; Request sent for CLOUD LOOKUP, please try again.

370 | show dpi Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide cheating 53 gross 54 web-based-email 55 malware-sites 56 phishing-and-other-frauds 57 proxy-avoidance-and-anonymizers 58 spyware-and-adware 59 music 60 government 61 nudity 62 news-and-media 63 illegal 64 content-deliv...

Page 371 - This command displays the DPI statistics.; Use this command to view the DPI statistics.

show dpi-stats show dpi-stats app [id <app> |user ip <ip-addr>][full] appcategory [id <appcat> |user ip <ip-addr>][full] session [full] webcategory [id <web> |user ip <ip-addr>][full] webreputation [id <rep> |user ip <ip-addr>][full] Description This c...

Page 373 - Web Reputation Web Reputation Id Total bytes

Web Reputation Web Reputation Id Total bytes -------------- ----------------- ----------- trustworthy-sites 5 1211900 moderate-risk-sites 3 2998 --------------------------- Total bytes :1214898 Command History Version Description Dell Networking W-SeriesInstant 6.4.0.2-4.1 This command is introduced...

Page 374 - show election; This command shows master W-IAP election statistics.; statistics; State

374 | show election Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show election show election {statistics} Description This command shows master W-IAP election statistics. Syntax Parameter Description statistics Shows master election statistics. Usage Guidelines Use this command...

Page 377 - show fault; The following example shows the output for the show fault command:

show fault show fault [history] Description This command displays the list of active faults that occur in the event of a system fault and the faults that werecleared from the system. Syntax Parameter Description history Displays the list of faults that were cleared. Usage Guidelines Use this command...

Page 379 - show ids; Displays the signal details for the W-IAP.; Use this command to view the intrusion detection details.; The following output is displayed for the show ids aps command:; Unknown Access Points Detected

show ids show ids {ap <mac>| aps| client <mac>|clients| phy-types| rap-types} Description This command displays the list of unknown APs and clients detected by the W-IAP with the IDS feature enabled. Syntax Parameter Description ap <mac> Displays the signal details for the W-IAP. a...

Page 381 - show ids-detection config

show ids-detection config show ids-detection config Description This command displays the list of intrusion detection policies configured on a W-IAP. Usage Guidelines Use this command to view a list of intrusion detection policies enabled for a W-IAP. Example The following output is displayed for th...

Page 383 - show ids-protection config; Indicates if a policy is enabled or disabled.

show ids-protection config show ids-protection config Description This command displays the list of infrastructure protection policies for a W-IAP. Usage Guidelines Use this command to view the status of infrastructure protection policies on a W-IAP. Examples The following output is displayed for th...

Page 385 - show image

show image show image version Description This command displays the Instant software version running on a W-IAP. Example The following example shows the output of show image version command: Primary Partition Build Time :2013-03-31 11:47:06 PDT Primary Partition Build Version :6.2.1.0-3.3.0.0_37845 ...

Page 386 - show interface counters; Use this command to view table of L2 interface counters.

386 | show interface counters Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show interface counters show interface counters Description This command shows the Ethernet interface packet counters for the W-IAP. Usage Guidelines Use this command to view table of L2 interface counte...

Page 388 - Access Rules

388 | show inbound-firewall-rules Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show inbound-firewall-rules show inbound-firewall-rules Description This command displays the details of inbound firewall rules configured on a W-IAP. Usage Guidelines Use this command to view the de...

Page 389 - show ip dhcp database; This command displays the DHCP server settings.

show ip dhcp database show ip dhcp database Description This command displays the DHCP server settings. Usage Guidelines Use this command to the DHCP server settings. The DHCP server is a built-in server, used for networks in whichclients are assigned IP address by the Virtual Controller. Example Th...

Page 390 - show ip igmp; Displays details for the IGMP multicast group.

390 | show ip igmp Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ip igmp show ip igmp group [maddr <multicast-addr>] Description This command displays information about the Internet Group Management Protocol (IGMP) group table. Syntax Parameter Description maddr <m...

Page 391 - VLAN

Parameter Description VLAN Indicates the VLAN ID associated with the multicast groups or a specific multicast groupaddress. Destination Indicates the destination to which the multicast packets are routed. Age Indicates the aging time of the forwarding table entries. Command History Version Descripti...

Page 392 - show ip interface brief

392 | show ip interface brief Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show ip interface brief show ip interface brief Description This command displays a summary of IP related information for all interfaces configured on a W-IAP. Usage Guidelines Use this command to view a...

Page 393 - show ip route; This command displays the W-IAP routing table.; Use this command to view the IP routes configured for a W-IAP.

show ip route show ip route Description This command displays the W-IAP routing table. Usage Guidelines Use this command to view the IP routes configured for a W-IAP. Examples The following output shows the ip address of routers and the VLANs to which they are connected. Kernel IP routing table Dest...

Page 394 - show lacp status

394 | show lacp status Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show lacp status show lacp status Description This command displays the Link Aggregation Control Protocol (LACP) configuration status on a W-IAP. Usage Guidelines Use this command to view the LACP status on W-I...

Page 395 - show l2tpv3 config

show l2tpv3 config show l2tpv3 config Description This command displays the L2TPV3 session and tunnel configuration details. Usage Guidelines Use this command to view the tunnel and session configuration details. Example The following example shows the output of the show l2tpv3 config command: (Inst...

Page 397 - show l2tpv3 global; show l2tpv3 global parameter; Use this command to view the hostname configured.; L2TPV3 Global configuration; Host Name

show l2tpv3 global show l2tpv3 global parameter Description This command displays L2TPv3 global configuration details such as hostname. Usage Guidelines Use this command to view the hostname configured. Example The following example shows the output of the show l2tpv3 global parameter command: L2TPV...

Page 398 - show l2tpv3 session; show l2tpv3 session status; This command displays the L2TP session connectivity status.; Use this command to view the session connectivity status.; data sequencing required: OFF

398 | show l2tpv3 session Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show l2tpv3 session show l2tpv3 session status Description This command displays the L2TP session connectivity status. Usage Guidelines Use this command to view the session connectivity status. Example The f...

Page 399 - show l2tpv3 system; show l2tpv3 system statistics; This command displays the L2TPV3 system statistics details.; Use this command to view the tunnel and session statistics.; Message RX Good RX Bad TX

show l2tpv3 system show l2tpv3 system statistics Description This command displays the L2TPV3 system statistics details. Usage Guidelines Use this command to view the tunnel and session statistics. Example The following example shows the output of the show l2tpv3 system statistics command: (Instant ...

Page 401 - show l2tpv3 tunnel

show l2tpv3 tunnel show l2tpv3 tunnel {config | status} Description This command displays the L2TP tunnel status and configuration details. Usage Guidelines Use this command to view the tunnel connectivity status and configuration details. Example The following example shows the output of the show l...

Page 403 - Use this command to view the L3 mobility information for a W-IAP.; show l3-m obility config

show l3-mobility show l3-mobility {config| datapath| events [<count> <mac>]| status} Description This command displays details about the Layer-3 (L3) events, mobility configuration, and roaming status of the W-IAP clients. Syntax Parameter Description config Displays the L3 mobility conf...

Page 404 - show l3-m obility datapath

404 | show l3-mobility Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Column Description Virtual Controller IP Displays the Virtual Controller IP address. The Virtual Controller IPconfiguration for each W-IAP allows the clients to roam seamlessly among allthe W-IAPs. Subnet Indic...

Page 405 - show l3-m obility events

Parameter Description l Tx Mcasts - Displays information about multicast packets transmitted. l ARP Proxy Pkts - Displays information packets resolved to destination IP addressby the proxy Address Resolution Protocol (ARP) l Tx Jumbo MTU - Displays information about the Maximum Transmission Unit(MTU...

Page 406 - show l3-m obility status

406 | show l3-mobility Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description FAP IP Indicates the IP address of the W-IAP in the foreign subnet. HAP IP Indicates the IP address of the W-IAP in the home subnet, to which the client iscurrently connected. VC IP Indica...

Page 410 - show log apifmgr; count

410 | show log apifmgr Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show log apifmgr show log apifmgr <count> Description This command shows the log information for W-IAP interface manager. Syntax Parameter Description count Starts displaying the log output from the speci...

Page 411 - show log convert; This command shows image conversion details for the W-IAP.

show log convert show log convert Description This command shows image conversion details for the W-IAP. Command History Version Description Dell Networking W-Series Instant6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode Dell...

Page 412 - show log debug

412 | show log debug Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show log debug show log debug{count} Description This command shows the W-IAP full log. Syntax Parameter Description <count> Starts displaying the log output from the specified number of lines from the endo...

Page 413 - show log driver

show log driver show log driver <count> Description This command displays the status of drivers configured on the W-IAP. Command History Version Description Dell Networking W-Series Instant6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Pri...

Page 414 - show log kernel; This command shows AP’s kernel logs.

414 | show log kernel Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show log kernel show log kernel Description This command shows AP’s kernel logs. Command History Version Description Dell Networking W-SeriesInstant 6.2.1.0-3.3 This command is introduced. Command Information W-...

Page 416 - VC IP

416 | show log l3-mobility Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Content Description VC IP Indicates the IP address of the Virtual Controller. Additional Info Displays additional information if any. Command History Version Description Dell Networking W-Series Instant6.2....

Page 417 - show log network; This command shows network logs for the W-IAP.

show log network show log network <count> Description This command shows network logs for the W-IAP. Syntax Parameter Description <count> Starts displaying the log output from the specified number of lines from the endof the log. Command History Version Description Dell Networking W-Seri...

Page 418 - show log pppd

418 | show log pppd Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show log pppd show log pppd <count> Description Shows the Point-to-Point Protocol daemon (PPPd) network connection details. Syntax Parameter Description <count> PPPd network count. Command History Vers...

Page 419 - show log rapper; This command show details the VPN connection logs in detail.

show log rapper show log rapper Description This command show details the VPN connection logs in detail. Command History Version Description Dell Networking W-Series Instant6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privileged EXEC mode Dell...

Page 420 - show log sapd; This command shows the SAPd details.

420 | show log sapd Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show log sapd show log sapd <count> Description This command shows the SAPd details. Syntax Parameter Description <count> Starts displaying the log output from the specified number of lines from the en...

Page 421 - show log security; This command shows security logs of the W-IAP.

show log security show log security <count> Description This command shows security logs of the W-IAP. Syntax Parameter Description <count> Starts displaying the log output from the specified number of lines from the endof the log. Command History Version Description Dell Networking W-Se...

Page 422 - show log system

422 | show log system Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show log system show log system <count> Description This command shows system logs of W-IAP. Syntax Parameter Description <count> Starts displaying the log output from the specified number of lines f...

Page 423 - show log upgrade

show log upgrade show log upgrade Description This command shows image download from URL and upgrade details for both local image file and URL for the W-IAP. Command History Version Description Dell Networking W-SeriesInstant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform...

Page 424 - show log user

424 | show log user Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show log user show log user [count] Description This command shows the W-IAP user logs. Syntax Parameter Description count Starts displaying the log output from the specified number of lines from the end ofthe log...

Page 425 - This command shows the W-IAP user debug logs.

show log user-debug show log user-debug [count] Description This command shows the W-IAP user debug logs. Syntax Parameter Description count Starts displaying the log output from the specified number of lines from the end ofthe log. Command History Version Description Dell Networking W-Series Instan...

Page 426 - This command shows VPN tunnel status for the W-IAP.

426 | show log vpn-tunnel Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show log vpn-tunnel show log vpn-tunnel [count] Description This command shows VPN tunnel status for the W-IAP. Syntax Parameter Description count Starts displaying the log output from the specified number o...

Page 427 - show log wireless; This command shows wireless logs of the W-IAP.

show log wireless show log wireless [<count>] Description This command shows wireless logs of the W-IAP. Syntax Parameter Description <count> Starts displaying the log output from the specified number of lines from the end ofthe log. Command History Version Description Dell Networking W-...

Page 428 - show memory; Displays the information about memory utilization for a W-IAP.; The following example shows the output of the show memory command:

428 | show memory Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show memory show memory Description Displays the information about memory utilization for a W-IAP. Usage Guidelines Use this command to view information about memory utilization on a W-IAP. Example The following exa...

Page 430 - The following output is displayed for the show mgmt-user command:

430 | show mgmt-user Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show mgmt-user show mgmt-user Description This command displays the credentials for the admin users for the W-IAP management interface. Usage Guidelines Use this command to view the admin user credentials require...

Page 431 - In Use

Column Description NAS is configured. In Use Indicates if the server is in use. RFC3576 Indicates if the W-IAPs are configured to process RFC 3576-compliantChange of Authorization (CoA). NAS IP address Displays the IP address of the Network Access Server (NAS) if NAS isconfigured. Name (Management U...

Page 432 - show network; This command shows network configuration details for a W-IAP.; Displays the name of a network profile.

432 | show network Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show network show network <name> Description This command shows network configuration details for a W-IAP. Syntax Parameter Description <name> Displays the name of a network profile. Usage Guidelines Us...

Page 433 - Work without usable uplink :Disabled

Work without usable uplink :Disabled Percentage of Airtime: :Unlimited Overall Limit: :Unlimited Per-user Limit: :Unlimited Command History Version Description Dell Networking W-Series Instant 6.2.1.0-3.3 This command is introduced. Command Information W-IAP Platform Command Mode All platforms Privi...

Page 434 - Use this command to view the status of the network configurations.

434 | show network-summary Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show network-summary show network-summary Description This command displays the status of the available network configurations on the W-IAP. Usage Guidelines Use this command to view the status of the netwo...

Page 435 - show opendns; The following example shows the output of show opendns command:

show opendns show opendns [support] Description This command displays the open DNS configuration details for a W-IAP. Syntax Parameter Description support Displays if the OpenDNS credentials if the OpenDNS service is configuredon the W-IAP. Usage Guidelines Use this command to view open DNS configur...

Page 436 - show port status; bond0 GE down up; Port

436 | show port status Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show port status show port status Description Displays the activity statistics on each of the port on the controller. Example The following example shows the output of the show port status command: (Instant AP)...

Page 437 - show pppoe; This command shows PPPoE debug logs and uplink status.; Displays PPPoE configuration details.; show pppoe config

show pppoe show pppoe {config|debug logs|debug status} Description This command shows PPPoE debug logs and uplink status. Syntax Parameter Description config Displays PPPoE configuration details. debug logs Displays PPPoE debug logs. debug status Displays the uplink status. Example show pppoe config...

Page 439 - show process; This command displays a list of processes running on a W-IAP.; PID Uid VmSize Stat Command

show process show process Description This command displays a list of processes running on a W-IAP. Usage Guidelines Use this command to view the processes running on the W-IAP for debugging purpose. Example The following example shows the partial output for the show process command: PID Uid VmSize ...

Page 440 - show proxy config; Displays the IP address of the HTTP proxy.

440 | show proxy config Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show proxy config show proxy config Description This command displays the HTTP proxy configuration settings on a W-IAP. Example The following example shows the output of show proxy config command: Proxy server...

Page 441 - show radio config; and

show radio config show radio config Description This command displays the 2.4 GHz and 5 GHz radio configuration details for a W-IAP. Usage Guidelines Use this command to view the 2.4 GHz and 5 GHz radio configuration details for a W-IAP. Example The following example shows the output of show radio c...

Page 443 - show radius-servers support; Use this command to view the RADIUS server information for a W-IAP.

show radius-servers support show radius-servers support Description This command displays the RADIUS server configuration details for a W-IAP. Usage Guidelines Use this command to view the RADIUS server information for a W-IAP. Example The following example shows the output of show radius-servers su...

Page 444 - Indicates the port number used for sending AirGroup CoA.

444 | show radius-servers support Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Airgroup RFC3576 port Indicates the port number used for sending AirGroup CoA. Deadtime Indicates the RADIUS server dead-time. Command History Version Description Dell Networkin...

Page 445 - Indicates the transaction ID for which you want to view the output.

show rft trans-id show rft trans-id {<id>| all} Description This command shows the transaction IDs of tests performed for RF troubleshooting. Syntax Parameter Description <id> Indicates the transaction ID for which you want to view the output. all Displays all the transaction IDs associa...

Page 446 - show rft profile; Displays the parameters for all test profiles.; Usage guidelines

446 | show rft profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show rft profile show rft profile {all|antenna-connectivity|ht-link-quality|link-quality|raw} Description This command shows the RF test profile for testing RF parameters such as antenna connectivity, link qual...

Page 451 - show snmp-configuration

show snmp-configuration show snmp-configuration Description This command displays the Simple Network Management Protocol (SNMP) configuration details for a VirtualController. Usage Guidelines Use this command to view the SNMP information configured on a Virtual Controller. Example The following exam...

Page 453 - This command displays the list of SNMP traps in queue.; Use this command to view the SNMP traps in queue.

show snmp trap-queue show snmp trap-queue Description This command displays the list of SNMP traps in queue. Usage Guidelines Use this command to view the SNMP traps in queue. Example The following example shows the partial output of show snmp trap-queue command: 2013-05-12 14:05:27 An AP (NAME d8:c...

Page 454 - This command displays the list of spectrum alerts for a W-IAP.; Spectrum Alerts; Timestamp

454 | show spectrum-alert Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show spectrum-alert show spectrum-alert Description This command displays the list of spectrum alerts for a W-IAP. Syntax Parameter Description <count> Filters the alerts based on the specified number....

Page 455 - show stats; global; show stats ap; Usage

show stats show stats {ap <IP-address>| client <MAC-address> | global | network <network-name>} [count] Description This command displays the aggregate statistics for W-IAPs, W-IAP clients, W-IAP cluster, and network profilesconfigured on a W-IAP. Syntax Parameter Description ap &l...

Page 456 - show stats client

456 | show stats Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide --------- ------------------- ---------------- ----------------------- ----------------------------- ----------------------- --------------------------- --------------------------------- ------- ---------------------...

Page 461 - show subscription-aps; This command displays the subscription status of a W-IAP.; subscription enabled by manually :disable

show subscription-aps show subscription-aps Description This command displays the subscription status of a W-IAP. Example (Instant AP) (config) # show subscription-aps IAP controlled by Cloud-Server:disable subscription enabled by manually :disable Subscription Ap List -------------------- MAC Addre...

Page 462 - show summary; This command shows the current configuration details.; Shows the difference in configuration.

462 | show summary Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show summary show summary {<difference> | support} Description This command shows the current configuration details. Syntax Parameter Description <difference> Shows the difference in configuration. supp...

Page 463 - show swarm; mesh ldart State :suspending

show swarm show swarm {state|mode} Description This command displays the current status of the W-IAP cluster and indicates if W-IAPs are in a cluster or standalonemode. Usage Guidelines Use this command to view the current status of the W-IAP cluster and to view information about the functioningmode...

Page 464 - The output of this command is modified.

464 | show supported-cert-formats Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show supported-cert-formats show supported-cert-formats Description This command displays the supported server and CA certificate formats. Usage Guidelines Use this command to view the list certifica...

Page 467 - This command displays all the tacacs servers configured on a W-IAP.

show tacacs-servers show tacacs-servers Description This command displays all the tacacs servers configured on a W-IAP. Usage Guidelines Use this command to view the list of tacacs servers available on a W-IAP. Example The following example shows the output of the show tacacs-servers command: TACACS...

Page 469 - show uncommitted-config

show uncommitted-config show uncommitted-config Description This command displays the current configuration details that are yet to be committed and saved on the W-IAP. Usage Guidelines Use this command to view the uncommitted configuration details. Use the commit apply command to commit theconfigur...

Page 470 - show upgrade info; This command displays the image upgrade details for a W-IAP.; Use this command to view the image upgrade details for a W-IAP.; Indicate the current status of the image upgrade.

470 | show upgrade info Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show upgrade info show upgrade info Description This command displays the image upgrade details for a W-IAP. Usage Guidelines Use this command to view the image upgrade details for a W-IAP. Example The followi...

Page 472 - show uplink; Displays the uplink interface configuration details for a W-IAP.; Indicates if the uplink preemption is enabled.

472 | show uplink Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show uplink show uplink {config|stats} Description This command displays uplink configuration details and status of for a W-IAP. Syntax Parameter Description show uplink config Displays the uplink interface configur...

Page 475 - Uplink Vlan Current :0; Uplink Vlan Current

show uplink-vlan show uplink-vlan Description This command displays the uplink VLAN configuration details for the management traffic. Usage Guidelines Use this command to view the uplink VLAN configuration details for management traffic. The uplink managementVLAN configuration allows you to tag mana...

Page 476 - show users; This command displays users configured for a W-IAP.; Use this command to view the W-IAP user credentials.; The following output is displayed for the show user command:; Indicates the password details of the users.

476 | show users Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show users show user [portal| Radius] Description This command displays users configured for a W-IAP. Syntax Parameter Description portal Displays the W-IAP user credentials. radius Displays the user credentials for ...

Page 479 - Displays the list of channels valid for a W-IAP in the 2.4 GHz band.

Parameter Description 2.4 GHz Displays the list of channels valid for a W-IAP in the 2.4 GHz band. 5.0 GHz Displays the list of channels valid for a W-IAP in the 5.0 GHz band. Command History Version Description Dell Networking W-Series Instant6.2.1.0-3.3 This command is introduced. Command Informat...

Page 480 - show version

480 | show version Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show version show version Description This command displays the Instant software version running on a W-IAP. Example The following example shows the output of the show version command: Aruba Operating System Softwa...

Page 481 - show vpn; Displays the status of the VPN connections enabled on a W-IAP.; vpn primary

show vpn show vpn {config|status|tunnels} Description This command displays the status and configuration details for VPN-enabled W-IAPs. Syntax Parameter Description config Displays configuration details for the VPN-enabled W-IAPs. status Displays the status of the VPN connections enabled on a W-IAP...

Page 482 - The t unnels keyword was added.

482 | show vpn Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide l vpn monitor-pkt-send-freq l vpn ikepsk l gre type l gre primary l gre per-ap-tunnel The following example shows the output displayed for show vpn status command: profile name:default ---------------------------------...

Page 483 - White List; Domain Name

show walled-garden show walled-garden Description This command displays the domain names and websites that are blacklisted or whitelisted by a W-IAP. Usage Guidelines Use this command to view the walled garden configuration details for a W-IAP. A walled garden typically controlsaccess to Web content...

Page 484 - Displays the Wi-Fi configuration parameters enabled on a W-IAP.; show wifi-uplink auth log; The output for this command displays the following information:; Displays the WPA passphrase configured for the Wi-Fi uplink.

484 | show wifi-uplink Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show wifi-uplink show wifi-uplink {auth log |config | status} Description This command displays the configuration details, the status, and authentication log for the Wi-Fi uplinks configuredon a W-IAP. Syntax P...

Page 485 - show wifi-uplink status

show wifi-uplink status The following output is displayed for the show wifi-uplink status command: configured :YES enabled :YES The output of this command indicates if the Wi-Fi uplink is configured and enabled on the W-IAP. Command History Version Description Dell Networking W-Series Instant6.2.1.0...

Page 488 - Use this command to view the wired profiles configured on a W-IAP.; Indicates the name of the wired port profile.

488 | show wired-port-settings Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show wired-port-settings show wired-port-settings Description This command displays the list of wired profiles configured on a W-IAP. Usage Guidelines Use this command to view the wired profiles configu...

Page 489 - poe

Column Description on the capabilities of the client, the AP, and the cable. poe Indicates if Power over Ethernet (PoE) is enabled. In Use Indicates if the wired profile is in use. Authentication Method Indicates the authentication method configured for the wired profile. Port Indicates the port num...

Page 490 - show wispr config

490 | show wispr config Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide show wispr config show wispr config Description This command displays the Wireless Internet Service Provider roaming (WISPr) authentication parametersconfigured on a W-IAP. Usage Guidelines Use this command to...

Page 491 - This command displays the XML API server configuration details.; Use this command to view the XML API server configuration details.

show xml-api-server show xml-api-server config Description This command displays the XML API server configuration details. Usage Guidelines Use this command to view the XML API server configuration details. Example The following example shows the output of the show xml-api-server command: ip :192.0....

Page 492 - This command configures SNMP parameters.; community; This command configures SNMP on the W-IAPs only.

492 | snmp-server Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide snmp-server snmp-server community <string> host <ipaddr> version {1 <name> udp-port <port>}|{2c|3 <name> [inform][udp-port <port>]} user <name> <auth-prot> <passwor...

Page 494 - This command configures the subscription status for a W-IAP.; Enter the subscription status for the W-IAP.; Use this command to subscribe the W-IAP based on its MAC address.

494 | subscription-ap Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide subscription-ap subscription-ap <MAC-address> status <status> no… Description This command configures the subscription status for a W-IAP. Syntax Command/Parameter Description <MAC-address> Ent...

Page 495 - This command enables the subscription of a W-IAP.; Removes the configuration.; Use this command to enable the subscription of the W-IAP.

subscription-ap-enable subscription-ap-enable no… Description This command enables the subscription of a W-IAP. Syntax Command/Parameter Description subscription-ap-enable Enables the subscription for a W-IAP. no Removes the configuration. Usage Guidelines Use this command to enable the subscription...

Page 496 - syslocation; Allows you to specify a physical location.; Use this command to define the physical location of the W-IAP.

496 | syslocation Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide syslocation syslocation <syslocation> no… Description This command allows you to define the physical location for the W-IAP. Syntax Command/Parameter Description <syslocation> Allows you to specify a phy...

Page 499 - This command configures Syslog server for a W-IAP.; Use this command to configure syslog server for a W-IAP.

syslog-server syslog-server <IP-address> no… Description This command configures Syslog server for a W-IAP. Syntax Parameter Description Range Default syslog-server <IP- address> Specifies the IP address to configure the syslogserver. — — no… Removes the configuration. — — Usage Guidelin...

Page 500 - Enables Telnet access to the Instant CLI.; Use this command to enable Telnet access to the Instant CLI.

500 | telnet-server Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide telnet-server telnet-server no… Description This command enables Telnet access to Instant command line interface (CLI). Syntax Command/Parameter Description telnet-server Enables Telnet access to the Instant CLI. ...

Page 501 - This command enables Secure Shell (SSH) access to Instant CLI.; Enables terminal access to the Instant CLI.; Use this command to enable SSH access to the Instant CLI.

terminal-access terminal-access no… Description This command enables Secure Shell (SSH) access to Instant CLI. Syntax Command/Parameter Description terminal-access Enables terminal access to the Instant CLI. no… Removes the configuration. Usage Guidelines Use this command to enable SSH access to the...

Page 502 - This command configures TFTP dump server for a W-IAP.; Configures TFTP dump server IP address.; The following example configures a TFTP dump server:

502 | tftp-dump-server Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide tftp-dump-server tftp-dump-server <IP-address> no… Description This command configures TFTP dump server for a W-IAP. Syntax Parameter Description tftp-dump-server <IP-address> Configures TFTP dump s...

Page 503 - traceroute; This command traces the route to the specified IP address.; Displays the destination IP address.; Use this command to identify points of failure in your network.

traceroute traceroute <ipaddr> Description This command traces the route to the specified IP address. Syntax Parameter Description <ipaddr> Displays the destination IP address. Usage Guidelines Use this command to identify points of failure in your network. Example The following example ...

Page 504 - These commands are introduced.

504 | upgrade-image Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide upgrade-image upgrade-image <url> upgrade-image2 <url> upgrade-image2-no-reboot Description These commands allow you to upgrade a W-IAP to use a new image file. Syntax Parameter Description upgrade-ima...

Page 505 - uplink; This command configures uplink connections.; uplink

uplink uplink enforce {ethernet| cellular |wifi | none} failover-internet failover-internet-check-timeout failover-internet-pkt-lost-cnt <count> failover-internet-pkt-send-freq <frequency> failover-vpn-timeout <seconds> preemption uplink-priority {cellular <priority> | ethern...

Page 506 - preemption; Enforcing uplinks

506 | uplink Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Parameter Description Range Default packets are sent to verify theuplink availability using theInternet. failover-vpn-timeout <seconds> Configures a duration to wait foran uplink switch based on VPNstatus. — 180sec...

Page 507 - Uplink Switchover; Uplink Switching based on VPN Status; The following example configures uplink priority:

Uplink Switchover The default priority for uplink switchover is Ethernet and then 3G/4G. The W-IAP has the ability to switch to the lowerpriority uplink if the current uplink is down. Uplink Switching based on VPN Status Instant supports switching uplinks based on the VPN status when deploying mixed...

Page 508 - The following example configures uplink management VLAN:

508 | uplink-vlan Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide uplink-vlan uplink-vlan <vlan-ID> Description This command configures uplink VLAN for management traffic on a W-IAP. Syntax Parameter Description Range Default <vlan-ID> Assigns a VLAN ID for the uplinkm...

Page 509 - user; Assigns a password for the W-IAP user; The following example configures an employee user for a W-IAP:

user user <username> [<password>] [portal| radius] no… Description This command creates users for a W-IAP. Syntax Parameter Description user <username> Creates a username for the W-IAP user. <password> Assigns a password for the W-IAP user portal Configures a guest user. radi...

Page 511 - version; This command configures a version number for the W-IAP.

version version <version-number> Description This command configures a version number for the W-IAP. Syntax Parameter Description version <version-number> Assigns a version number for the W-IAP. Usage Guidelines Use this command to configure a version number for the W-IAP. Example The fo...

Page 512 - This command configures the location of the W-IAP.; Specifies the country of operation for a W-IAP.; Use this command to configure the country code for W-IAPs.

512 | virtual-controller-country Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide virtual-controller-country virtual-controller-country <country-code> no… Description This command configures the location of the W-IAP. Syntax Parameter Description virtual-controller-country &l...

Page 513 - Assigns an IP address for the Virtual Controller.

virtual-controller-ip virtual-controller-ip <IP-address> Description This command configures an IP address for the Virtual Controller. Syntax Parameter Description virtual-controller-ip <IP- address> Assigns an IP address for the Virtual Controller. Usage Guidelines Use this command to c...

Page 514 - Defines a unique name for the Virtual Controller.; Use this command to assign a name for the Virtual Controller.

514 | virtual-controller-key Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide virtual-controller-key virtual-controller-key <name> Description This command configures a unique name for the Virtual Controller. Syntax Parameter Description virtual-controller-key <name> De...

Page 515 - This command configures a VLAN for the Virtual Controller.

virtual-controller-vlan virtual-controller-vlan <virtual-controller-vlan> <virtual-controller-mask> <virtual-controller-gateway> no… Description This command configures a VLAN for the Virtual Controller. Syntax Parameter Description virtual-controller-vlan <virtual-controller-vl...

Page 516 - vpn backup

516 | vpn backup Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide vpn backup vpn backup <name> no… Description This command configures a secondary or backup VPN server for VPN connections. Syntax Parameter Description vpn backup <name> Configures a fully qualified domai...

Page 517 - Enables fast failover feature for VPN connections.; The following example configures the VPN fast failover feature:

vpn fast-failover vpn fast-failover no… Description This command configures fast failover feature for VPN connections. Syntax Parameter Description vpn fast-failover Enables fast failover feature for VPN connections. no… Removes the configuration. Usage Guidelines Use this command to configure fast ...

Page 518 - The following example configures an automatic GRE tunnel:

518 | vpn gre-outside Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide vpn gre-outside vpn gre-outside no… Description This command enables automatic configuration of the GRE tunnel between the W-IAP and the controller. Usage Guidelines Use this command to enable automatic configur...

Page 520 - vpn ikepsk; This command configures user credentials for the VPN connection.; The following commands enable user access to VPN connection.

520 | vpn ikepsk Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide vpn ikepsk vpn ikepsk <ikepsk> username <username> password <password> no… Description This command configures user credentials for the VPN connection. Syntax Parameter Description vpn ikepsk <ik...

Page 521 - The following example configures a count for the lost packets:

vpn monitor-pkt-lost-cnt vpn monitor-pkt-lost-cnt <count> no... Description This command configures the number of lost packets after which the W-IAP can determine that the VPN connectionis not available. Parameter Description Range Default vpn monitor-pkt-lost-cnt <count> Defines the num...

Page 522 - The following example configures the VPN monitoring frequency:

522 | vpn monitor-pkt-send-freq Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide vpn monitor-pkt-send-freq vpn monitor-pkt-send-freq <frequency> no... Description This command configures the frequency at which the W-IAP can verify if the active VPN connection is available. Sy...

Page 523 - vpn preemption; vpn preemption; The following example enables VPN pre-emption.

vpn preemption vpn preemption no… Description This command enables pre-emption to allow the VPN tunnel to switch back to the primary host after a failover. Syntax Parameter Description vpn preemption Enables pre-emption to allow the VPN tunnel to switch to the primary VPNserver when it becomes avail...

Page 524 - The following example configures a primary VPN server:

524 | vpn primary Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide vpn primary vpn primary <name> no... Description This command configures a primary Virtual Private Networks (VPN) server for VPN connections. Syntax Parameter Description Range Default vpn primary <name>...

Page 526 - Enables users to reconnect to the VPN during a VPN failover.

526 | vpn reconnect-user-on-failover Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide vpn reconnect-user-on-failover vpn reconnect-user-on-failover no… Description This command enables the users to reconnect to the VPN when the primary VPN tunnel fails. Syntax Parameter Description...

Page 529 - Creates a wired profile.

wired-port-profile wired-port-profile <port> access-rule-name <name> allowed-vlan <vlan> auth-server <name> captive-portal {<type>[exclude-uplink <types>]|external[exclude-uplink <types>| profile<name>[exclude-uplink <types>]]} content-filtering ...

Page 531 - Configures unrestricted access control.

Command/Parameter Description Range Default l equals — The rule is applied only if theattribute value is equal to thespecified string. l not-equals — The rule is applied onlyif the attribute value is not equal to thespecified string. l starts-with — The rule is applied only ifthe attribute value beg...

Page 532 - shutdown

532 | wired-port-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command/Parameter Description Range Default the value of the attribute returned. Toset a user role, the value of theattribute must already be configuredon the W-IAP. shutdown Shuts down the admin status port ...

Page 533 - The following example configures a guest wired profile:

(Instant AP)(wired ap profile"employeeWired1")# switchport-mode trunk (Instant AP)(wired ap profile"employeeWired1")# allowed-vlan 2,3,5 (Instant AP)(wired ap profile"employeeWired1")# native-vlan 1 (Instant AP)(wired ap profile"employeeWired1")# mac-authentication (I...

Page 536 - permit

536 | wlan access-rule Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command/Parameter Description Range Default of applications,run the show dpiapp allcommand. appcategory <appgrp> Specifies a rule to allow or denyaccess to a specific category ofapplication. To view the l...

Page 540 - dynamic RADIUS

540 | wlan auth-server Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command/Parameter Description Range Default IP-address> source address and VLAN forRADIUS packets. NO T E: Before configuring DRP IPaddress, ensure that dynamic RADIUS proxy is enabled, and a static Virtual ...

Page 542 - authenticated

542 | wlan captive-portal Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide wlan captive-portal wlan captive-portal authenticated background-color <background-color> banner-color <banner-color> banner-text <banner-text> custom-logo <name> decoded-texts <de...

Page 544 - This command configures profiles for external captive portal.

544 | wlan external-captive-portal Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide wlan external-captive-portal wlan external-captive-portal [profile-name] auth-text <text> auto-whitelist-disable https port <port> redirect-url <redirection-url> server <server-...

Page 546 - strings

546 | wlan ldap-server Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide wlan ldap-server wlan ldap-server <server-name> admin-dn <domain-name> admin-password <password> base-dn <base_domain-name> deadtime <time> filter <filter> key-attribute <...

Page 547 - The following example configures an LDAP server:

Command/Parameter Description Range Default key-attribute <key-attribute> Configures the attribute to use as akey when searching for the LDAPserver.For Active Directory, the value issAMAccount Name — — ip <IP-address> Configures the IP address of theLDAP server. — — port <port> Con...

Page 549 - This command configures a WLAN SSID profile.; Creates a WLAN SSID profile.

type {employee|voice|guest} vlan <vlan> wep-key <wep-key> wispr wmm-background-dscp <dscp> wmm-background-share <share> wmm-best-effort-dscp <dscp> wmm-best-effort-share <share> wmm-video-dscp <dscp> wmm-video-share <share> wmm-voice-dscp <dscp> ...

Page 550 - blacklist

550 | wlan ssid-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command/Parameter Description Range Default internal server. bandwidth-limit <limit> Configures an aggregate amountof bandwidth that each radio isallowed to provide for theconnected clients. 1—65535 — bl...

Page 552 - for the SSID profile.

552 | wlan ssid-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command/Parameter Description Range Default for the SSID profile. The DTIM interval determines howoften the W-IAP should deliver thebuffered broadcast and multicastframes to associated clients in thepowersavin...

Page 556 - RADIUS server at regular intervals.

556 | wlan ssid-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command/Parameter Description Range Default RADIUS server at regular intervals. radius-reauth-interval <minutes> Configures an interval at which W-IAPs can periodicallyreauthenticate all associated andau...

Page 558 - termination

558 | wlan ssid-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Command/Parameter Description Range Default operator is available only if themac-address-and-dhcp-opt ions attribute is selected inthe At t ribut e drop-down. termination Configures the EAP portion of802.1X au...

Page 559 - The following example configures an employee WLAN SSID profile:

Command/Parameter Description Range Default wmm-video-dscp <dscp> Allows you to specify the DSCPmapping value for the video traffic. 0—63 — wmm-video-share <share> Allocates bandwidth for videotraffic generated from videostreaming. — — wmm-voice-dscp <dscp> Allows you to specify th...

Page 560 - The following example configures a guest WLAN SSID profile:

560 | wlan ssid-profile Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide (Instant AP)(SSID Profile "employee1")# set-vlan mac-address-and-dhcp-options matches-regular-expression ..link 200 (Instant AP)(SSID Profile "employee1")# no wmm-background-dscp (Instant AP)(S...

Page 561 - clear —To clear a cipher suite; The following commands configure the Wi-Fi uplink profile:

wlan sta-profile wlan sta-profile essid <ESSID> cipher-suite <cipher-suite-string> wpa-passphrase <WPA-key> uplink-band <band> no… Description This command enables Wi-Fi uplink on a W-IAP. Syntax Command/Parameter Description Range Default wlan sta-profile Configures a Wi-Fi ...

Page 563 - Configures the TACACS server profile.; The following example configures the TACACS protocols:

wlan tacacs-server wlan tacacs-server <profile-name> ip <IP-address> port <port> key <key> timeout <seconds> retry-count <number> deadtime <minutes> no... Description This command is used to configure a TACACS server for management users. Syntax Command/Para...

Page 566 - The following example configures a walled garden profile:

566 | wlan walled-garden Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Example The following example configures a walled garden profile: (Instant AP)(config)# wlan walled-garden (Instant AP)(Walled Garden)# white-list <domain> (Instant AP)(Walled Garden)# black-list <do...

Page 567 - iPass

wlan wispr-profile wlan wispr-profile wispr-location-id-ac <ac> wispr-location-id-cc <cc> wispr-location-id-isocc <issoc> wispr-location-id-network <network> wispr-location-name-location <location-name> wispr-location-name-operator-name <operator-name> no... Descr...

Page 569 - write; memory; The W-IAP returns the following messages:

write write {erase <all> <reboot>|memory} Description This command saves the running configuration to memory or displays the running configuration on the screen. Thiscommand can also be used to erase the running configuration and return to factory default setting Syntax Parameter Descrip...

Page 571 - zonename; The following constraints apply to the AP zone configuration:

zonename zonename <name> no… Description This command configures a zone name for the W-IAP. You can configure zone settings on a W-IAP and the SSIDprofile, to assign an SSID to a specific W-IAP. Syntax Parameter Description zonename <name> Configures zone on a W-IAP. no… Removes the conf...

Page 572 - Terminology; Acronyms and Abbreviations; Abbreviation; List of abbreviations

Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Terminology | 572 Terminology Acronyms and Abbreviations The following table lists the abbreviations used in this document. Abbreviation Expansion ARM Adaptive Radio Management ARP Address Resolution Protocol BSS Basic Server Set BSS...

Page 573 - Glossary; Term; List of Terms

573 | Terminology Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide Abbreviation Expansion PEAP Protected Extensible Authentication Protocol PEM Privacy Enhanced Mail PoE Power over Ethernet RADIUS Remote Authentication Dial In User Service VC Virtual Controller VSA Vendor-Specific ...

Table of Contents:

Summary

Other Dell Models