Dell Latitude E7450/7450 (Late 2014)- User Manual

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down 2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold t...

2 Docking Your Computer Follow the steps to dock your computer:a. Place the docking spacer until the docking spacer clicks on its place in the docking station.b. Place the computer on the docking spacer to dock your computer. NOTE: This docking spacer can be used to dock only the Latitude E7250 / La...

3 Removing and Installing Components This section provides detailed information on how to remove or install the components from your computer. Recommended Tools The procedures in this document may require the following tools: • Small flat-blade screwdriver• Phillips screwdriver• Small plastic scribe...

Installing the Battery 1. Slide the battery into its slot until it clicks into place. 2. Follow the procedures in After Working Inside Your computer . Removing the Base Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove battery . 3. Perform the following steps as shown...

Installing the Base Cover 1. Place the base cover to align with the screw holes correctly on the computer. 2. Tighten the screws to secure the base cover to the computer. 3. Install battery . 4. Follow the procedures in After Working Inside Your computer . Removing the Hard Drive 1. Follow the proce...

Installing the Coin-Cell Battery 1. Place the Coin-cell battery on the computer. 2. Connect the coin-cell battery cable to the computer. 3. Install:a. base cover b. battery 4. Follow the procedures in After Working Inside Your computer . Removing the WWAN Card 1. Follow the procedures in Before Work...

4. Lift the display bezel from the display assembly. Installing the Display Bezel 1. Align the display bezel in place and snap it in place. 2. Align the hinge covers on display assembly and snap it in place. 3. Install the battery . 4. Follow the procedures in After Working Inside Your computer . Re...

Installing the Display Panel 1. Connect the display assembly cable to its connector on the display panel. 2. Place the display panel to its original position on the display assembly. 3. Tighten the screws to secure the display panel to the display assembly. 4. Install:a. display bezel b. battery 5. ...

Installing the Camera 1. Install the camera into its slot on the display panel. 2. Connect the camera cable to the camera. 3. Tighten the screws to secure the display panel to the display assembly. 4. Install thea. display panel b. display bezel c. battery 5. Follow the procedures in After Working I...

Installing the Keyboard 1. Align the keyboard to its slot. 2. Tighten the screws to secure the keyboard on the palmrest. 3. Connect the keyboard-backlight cable to the computer. 4. Installa. keyboard trim b. base cover c. battery . 5. Follow the procedures in After Working Inside Your computer Remov...

5. Perform the following steps as shown in the illustration:a. Pry the edges of the palmrest assembly [1]b. Lift up the palmrest away from the computer [2]. Installing the Palmrest 1. Align the palm rest assembly to its original position in the computer and snap it into place. 2. Connect the power L...

Removing the Speakers 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove:a. battery b. base cover c. hard drive d. keyboard trim e. keyboard f. palmrest 3. Perform the following steps as shown in the illustration:a. Disconnect the speaker cable [1].b. Unroute the cable from ...

Installing the Speaker 1. Align the speakers to their original position and tighten the screws to secure the speakers to the computer. 2. Route the speaker cable on the computer and connect it to the system board. 3. Install:a. palmrest b. keyboard c. keyboard trim d. hard drive e. base cover f. bat...

4. Installa. palmrest b. keyboard c. keyboard trim d. hard drive e. base cover f. battery . 5. Follow the procedures in After Working Inside Your computer Removing the Display-Hinge Cover 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove:a. battery b. base cover c. keyboard...

Installing the Display-Hinge Cover 1. Place the display-hinge cover and tighten the screws to secure the display-hinge cover to the system board. 2. Tighten the screw that secures hinge cap to the computer. 3. Instal:a. palmrest b. keyboard c. keyboard trim d. base cover e. battery 4. Follow the pro...

6. Perform the following steps as shown in the illustration:a. Remove the screws that secure the display assembly to the computer [1].b. Lift the display assembly from the computer [2]. Installing the Display Assembly 1. Insert the wireless antenna cables through the holes on the base chassis and co...

a. palmrest b. hard drive c. keyboard d. keyboard trim e. base cover f. battery 7. Follow the procedures in After Working Inside Your computer . Removing the System Board 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove:a. battery b. base cover c. keyboard trim d. keyboard...

5. Perform the following steps as shown in the illustration:a. Remove the screws that secure the system board to computer chassis [1].b. Lift the system board from the computer [2]. Installing the System Board 1. Align the system board in its place on the computer. 2. Tighten the screws to secure th...

e. palmrest f. hard drive g. keyboard trim h. keyboard i. base cover j. battery 6. Follow the procedures in After Working Inside Your computer . Removing the Heatsink 1. Follow the procedures in Before Working Inside Your Computer . 2. Remove:a. battery b. base cover c. keyboard trim d. keyboard e. ...

a. speaker b. system fan c. display assembly d. WLAN card e. WWAN card f. hard drive g. palmrest h. keyboard i. keyboard trim j. base cover k. battery 4. Follow the procedures in After Working Inside Your computer . Removing the Power Connector 1. Follow the procedures in Before Working Inside Your ...

Installing the Power Connector 1. Insert the power connector in its slot. 2. Connect the power connector to the system board. 3. Tighten the screw that secures the power connector to the system board. 4. Install:a. system board b. system fan c. speaker d. I/O board e. coincell battery f. camera g. d...

4 System Setup Boot Sequence Boot Sequence allows you to bypass the System Setup ‐ defined boot device order and boot directly to a specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the Dell logo appears, you can: • Access System Setup by pressing...

Keys Navigation NOTE: For the standard graphics browser only. <Esc> Moves to the previous page till you view the main screen. Pressing <Esc> in the main screen displays a message that prompts you to save any unsaved changes and restarts the system. <F1> Displays the System Setup he...

Table 12. Maintenance Option Description Service Tag Displays the service tag of your computer. Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default. Table 13. System Logs Option Description BIOS events Displays the system event log ...

System and Setup Password You can create a system password and a setup password to secure your computer. Password Type Description System password Password that you must enter to log on to your system. Setup password Password that you must enter to access and make changes to the BIOS settings of you...

Deleting or Changing an Existing System and/or Setup Password Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change the existing System and/or Setup password. You cannot delete or change an existing System or Setup password, if the Password Status is...

5 Diagnostics If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of running diagnostics is to test your computer's hardware without requiring additional equipment or risking data loss. If you are unable to fix the pro...

Device Status Lights Table 14. Device Status Lights Turns on when you turn on the computer and blinks when the computer is in a power management mode. Turns on when the computer reads or writes data. Turns on steadily or blinks to indicate battery charge status. Turns on when wireless networking is ...

6 Specifications NOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. For more information about the configuration of your computer, go to Help and Support in your Windows operating system and select the option to view informatio...

7 Contacting Dell NOTE: If you do not have an active Internet connection, you can find the contact information on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by country and produ...