Dell B-DCX-4s- Installation Manual

Page 2 - NOTE; DANGER

2 Port-Side Exhaust Kit Installation Procedure 53-1001802-01 Notes, Cautions, and Warnings NOTE A NOTE indicates important information that helps you make better use of your computer. CAUTIONSee the safety and regulatory information that shipped with your system. For additional regulatory informatio...

Page 3 - In this guide; Brocade Product Safety Notices; Installation guidelines; ATTENTION; Follow these general installation guidelines:

Port-Side Exhaust Kit Installation Procedure 3 53-1001802-01 In this guide • Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 • Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4 - DCX-4S Backbone Hardware Reference Manua; Installing the DCX-4S in equipment cabinet; Time required

4 Port-Side Exhaust Kit Installation Procedure 53-1001802-01 • Plan for cable management before installing the chassis. Cables can be managed in a variety of ways, such as by routing cables below the chassis, to either side of the chassis, through cable channels on the sides of the cabinet, or using...

Page 5 - a. Cut the bands that encircle the packaging.; Parts list; The following parts list refers to items illustrated in; TABLE 1; Item

Port-Side Exhaust Kit Installation Procedure 5 53-1001802-01 NOTE A fully populated PowerConnect B-DCX-4S weighs 103.50 kg (228.20 lb) with four FC8-48 port cards installed (192 ports) and requires a hydraulic or assisted lift to install it. 1. Unpack the PowerConnect B-DCX-4S. a. Cut the bands that...

Page 6 - FIGURE 1; Torque requirements; TABLE 2; Torque requirements for mounting screws; Screw size

6 Port-Side Exhaust Kit Installation Procedure 53-1001802-01 FIGURE 1 Port-Side Exhaust Kit assembly for 27 to 31 in. (68.58 to 78.74 cm) cabinets Torque requirements Use the following torque settings when tightening screws that secure the rack mount kit and DCX-4S to the equipment cabinet. TABLE 2 ...

Page 7 - Install cabinet hardware; Figure 1; FIGURE 2; Clip and retainer nut locations on cabinet rails

Port-Side Exhaust Kit Installation Procedure 7 53-1001802-01 Install cabinet hardware 1. Determine how the DCX-4S can be oriented in the equipment cabinet so that the nonport side has access to intake air (cool). 2. Install clip nuts (F in Figure 1 on page 6) or retainer nuts (G in Figure 1 on page ...

Page 8 - in each corner of the shelf (see; FIGURE 3; Shelf installed in cabinet

8 Port-Side Exhaust Kit Installation Procedure 53-1001802-01 3. Install the shelf (C in Figure 1 ): a. The shelf can be adjusted to a length of between 27 and 31 inches (68.58 and 78.74 cm) to accommodate your cabinet size. To lengthen or shorten the shelf, loosen the four 6-32 screws in the four sl...

Page 9 - FIGURE 4; Installing air duct into side slot on shelf

Port-Side Exhaust Kit Installation Procedure 9 53-1001802-01 FIGURE 4 Installing air duct into side slot on shelf 5. Install the top-rail assembly (A in Figure 1 on page 6) to the air-duct assembly: Refer to Figure 5 on page 10. a. The top-rail assembly can be adjusted to a length of between 27 and ...

Page 10 - FIGURE 5; Securing top rail in cabinet.; Install DCX-4S in cabinet

10 Port-Side Exhaust Kit Installation Procedure 53-1001802-01 FIGURE 5 Securing top rail in cabinet. 6. Secure the top-rail assembly to the cabinet with four 10-32 screws, two screws on each end of the top-rail assembly. • For rails with round holes:Use two 10-32 screws with washers (E in Figure 1 o...

Page 11 - specifications under; For rails with round holes, use the clip nuts (F in

Port-Side Exhaust Kit Installation Procedure 11 53-1001802-01 4. Carefully lift the DCX-4S and slide it into the cabinet. 5. Secure the DCX-4S to the cabinet with six 10-32 screws with washers. Tighten screws according to specifications under “Torque requirements” on page 6. NOTE Screws, clip nuts, ...

Page 12 - TABLE 3

12 Port-Side Exhaust Kit Installation Procedure 53-1001802-01 Installing with 18-24 in. (45.72 to 60.96 cm) kit Parts list The following parts list refers to items illustrated in Figure 7 on page 13. TABLE 3 Hardware for Port-Side Exhaust Kit for 18-in. to 24 in. (45.72 to 60.96 cm) cabinets Item De...

Page 13 - FIGURE 7; TABLE 4

Port-Side Exhaust Kit Installation Procedure 13 53-1001802-01 FIGURE 7 Port-Side Exhaust Kit assembly for 18 to 24 in. (45.72 to 60.96 cm) cabinets Torque requirements Use the following torque settings when tightening screws that secure the rack mount kit and DCX-4S to the equipment cabinet. TABLE 4...

Page 14 - Figure 7; FIGURE 8

14 Port-Side Exhaust Kit Installation Procedure 53-1001802-01 Install cabinet hardware 1. Determine how the DCX-4S can be oriented in the equipment cabinet so that the nonport side has access to intake air (cool). 2. Install clip nuts (H in Figure 7 on page 13) or retainer nuts (I in Figure 7 on pag...

Page 15 - FIGURE 9; Installing saddle to equipment cabinet

Port-Side Exhaust Kit Installation Procedure 15 53-1001802-01 3. Install the shelf saddle (E in Figure 7 on page 13) to the nonport side of the equipment cabinet .Install the saddle in the same vertical location as where the shelf installs on the port side of the rack. In using Figure 2 on page 7 as...

Page 18 - DCX-4S Backbone Hardware Reference Manual

18 Port-Side Exhaust Kit Installation Procedure 53-1001802-01 Use the two standard 10-32 screws (F in Figure 7 on page 13) with blue Loctite on the threads and alignment washers (J in Figure 7 on page 13) on each end of the top rail assembly. Tighten screws according to specifications under “Torque ...

Page 19 - on

Port-Side Exhaust Kit Installation Procedure 19 53-1001802-01 4. Carefully lift the DCX-4S and slide it into the cabinet. 5. Secure the DCX-4S to the cabinet with six 10-32 screws with washers, three screws on each side ( Figure 13 on page 19). Tighten screws according to specifications under “Torqu...

Dell B-DCX-4s- Installation Manual

Table of Contents:

Summary

Other Dell Models