Dell 8024 and 8024F - Manual

Dell 8024 and 8024F

Dell 8024 and 8024F – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
Page: / 56

Table of Contents:

  • Page 2 – PowerConnect
  • Page 4 – Figures
  • Page 6 – Introduction; FIP snooping
  • Page 7 – PFC; at
  • Page 8 – Configuration scenarios; General overview of deployment
  • Page 9 – Important notes prior to deployment; No Simple Mode; Disabling simple mode; tacking; updating firmware
  • Page 10 – Simple 1-link connection between devices
  • Page 12 – Overview of parallel configuration
  • Page 13 – Command-Line Interface Method
  • Page 14 – Step by Step explanation of CLI example
  • Page 15 – switchport mode general – this enables the port for mode general; sets the configuration-source for an FCF connection; exit - exits the interface configuration
  • Page 16 – Configuration overview of Dell PowerConnect M8024-k
  • Page 18 – Note that the provided Cisco commands should be referenced in the
  • Page 19 – Step by Step explanation of the CLI example; number based on the admin’s choice at configuration time).
  • Page 20 – member blade1 – this includes the blade1 zone into this zoneset.
  • Page 22 – The following command is used to give a; port status overview:; This example has been shortened from the actual results; Example of show interface brief command
  • Page 23 – ports states; the Cisco Nexus 5020 is the FCF. Type :; This command will show the current activated zoneset and all; Example of show zoneset active command; Basic Validation for the PowerConnect M8024-k configuration
  • Page 24 – Show interface status results
  • Page 25 – command the status of ports that may be impacted by; show spanning-tree blockedports command; be possible until this configuration error is corrected.; and FCF’s
  • Page 27 – This command will show more specific detail about the; Show lldp dcbx interface te1/0/20 detail
  • Page 28 – Basic Troubleshooting Areas; Problem
  • Page 34 – Validation; Follow the same
  • Page 35 – NPV; Multiple link configuration between switches and storage
  • Page 37 – CoS settings to establish minimum bandwidth for FCoE queue; Appendix A – M8024-k CLI example
  • Page 38 – Further notes on ETS / CoS behavior settings
  • Page 39 – Updating firmware; File Download page in the; Web UI or the; Command-line interface method; show version; Be patient as this procedure may take a few minutes
  • Page 41 – show version command. For the example given the; Web interface method; Firmware for the File Type and TFTP for the Transfer Mode.
  • Page 45 – Appendix A – Full CLI examples
  • Page 51 – Skipped port-channel 5 through 126 for space
  • Page 52 – Cisco Nexus 5548UP CLI example
  • Page 56 – Appendix B - Network Switch Versions; Switch Firmware Versions; Network switch; Software version; References
Loading the manual

Authors

Network Enabled Solutions Team,
Kevin Locklear

Contributor

Kili Land

Deploying FCoE (FIP Snooping) on
Dell PowerConnect 10G Switches:
M8024-k, 8024 and 8024F

A Dell Deployment Guide

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - PowerConnect

Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switches: M8024-k, 8024, and 8024F 2 This document is for informational purposes only and may contain typographical errors and technical inaccuracies. The content is provided as is, without express or implied warranties of any kind. © 2011 - 201...

Page 4 - Figures

Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switches: M8024-k, 8024, and 8024F 4 Cisco Nexus 5548UP CLI example .............................................................................. 52 Appendix B - Network Switch Versions .............................................................

Page 6 - Introduction; FIP snooping

Deploying FCoE (FIP Snooping) on Dell PowerConnect 10G Switches: M8024-k, 8024, and 8024F 6 Introduction The PowerConnect™ M8024-k, 8024 and 8024F switches are now DCB/DCBx capable with a downloadable update. Starting with firmware 4.2, the latest PowerConnect™ 10 Gigabit switches can now be used as...

Other Dell Models