DELANEY HARDWARE 301776 - User Manual

REGULATORY COMPLIANCE

This product complies with standards established by the following regulatory bodies:

• Federal Communications Commission (FCC) • Industry Canada

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

( 1 ) this device may not cause harmful interference, and ( 2 ) this device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT !

Changes or modifications not expressly approved by the manufacturer could void the user' authority to operate the equipment.

Removing lock from your Z-Wave gateway

Adding, Removing & Resetting lock

1

2

3

4

5

6

7

8

9

0

9

9

ZW300 Touchscreen Smartlock

with Delaney’s Smart Home Control App

On the interior side of the digital lock, You will remove the cover and

you will see a “R” (reset) button under the batteries (see exhibit A

illustration) Press “R” button for 5 seconds to return to the original

factory settings.

Your Smart Lock will be reset to its original settings once you hear 3

long beeps. After restoring default settings, you must run the door

handing identifying process (#1) again before programming any

other functions.

1)

Wake up your lock by touching the screen

2)

Open the Dela

n

ey Smart App on your mobile device

3)

Tap “add device” on your app, then enter to lock.

Enter Your Programming Code

If you hear 2 beeps from your lock the programming was successful. If

you hear 5 beeps from your lock you must start over again (the

programming failed).

Enter Your Programming Code

Adding lock from your Z-Wave gateway

1)

Wake up your lock by touching the screen

2)

Open the Dela

n

ey Smart App on your mobile device

3)

Tap “remove device” on your app, then enter to lock.

If you hear 2 beeps from your lock the programming was successful. If

you hear 5 beeps from your lock you must start over again (the

programming failed).

Resetting lock

Exhibit A

For questions, contact Delaney Hardware 1.800.952.4430

www.DelaneyHardware.com/smartlock

This product has been fully tested and certified to work with Z-Wave by the Z-Wave

Alliance. It is crafted using Z-Wave Plus, the latest device version ofZ-Wave. As

such, if the product does not work with your gateway, please be sure to check with

your gateway manufacturer that they have integrated this device with their gateway

for full operation. This device must be used in conjunction with a Security Enabled

Z-Wave Controller in order to fully utilize all implemented functions.

If at some stage, your primary controller is missing or inoperable, you may wish to

reset all of your Smart Lock setting to their factory defaults. To do this, press the R

button for more than 5 seconds and then release it. Your Smart Lock will be reset to

its original settings once you hear 3 long beeps. After restoring default settings, you

must run the door handing identifying process (#1) again before programming any

other functions.

R

Associations Groups

Group 1 is Lifeline. All unsolicited reports are sent to the node in Lifeline.

It can contain 1 node.

The lock can send the following commands through Lifeline:

• Device Reset Locally: triggered upon reset.

• Battery/notification: triggered upon low battery.

• Door Lock operation report: triggered upon a change in door lock

• Notification: triggered upon a change in door lock

For questions, contact Delaney Hardware 1.800.952.4430

www.DelaneyHardware.com/smartlock

Z-Wave Device Specific Key (DSK)

Please retain this instruction manual for future reference.

DSK

:

29544-05938-47406-46908-57915-61528-14561-17158