Page 2 - A MESSAGE TO OUR CUSTOMERS; WARNING; PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
1 A MESSAGE TO OUR CUSTOMERS We are glad that you selected the Professional Side Burner by DCS. Because this appliance contains featuresnot found on any other burner, we recommend that you read this entire booklet before your first use. Keepit in a handy place as it has answers to questions that may...
Page 3 - TABLE OF CONTENTS
TABLE OF CONTENTS 2 SAFETY PRACTICES AND PRECAUTIONS ..................................................................................................3-4 SIDE BURNER 131/132 SIDE MOUNT MODEL INSTALLATION ...................................................4-5 SIDE BURNER BUILT-IN MODEL INSTALLATION ...
Page 4 - SAFETY PRACTICES & PRECAUTIONS
3 SAFETY PRACTICES & PRECAUTIONS Improper use or installation is dangerous. Carefully follow these instructions. Always remove the cover before lighting the Professional Side Burner. Never use the SideBurner if a leak is present. Do not use a flame to check for gas leaks. Do not let children use...
Page 5 - INSTALLATION OF SIDE BURNER:; SPIDER AND INSECT WARNING!; MODEL INSTALLATION
INSTALLATION OF SIDE BURNER: All BGB131 and BGB132 models can be installed in combustible enclosure with zero clearance from theback, sides and bottom. A minimum of 6” from the back and sides must bemaintained from the Professional Side Burner abovethe cooking surface and a minimum of 1” below theco...
Page 7 - SIDE BURNER BUILT-IN MODEL INSTALLATION
SIDE BURNER BUILT-IN MODEL INSTALLATION 6 INSTALLATION OF SIDE BURNER BUILT-IN: All BGB131-BI and BGB132-B I models can be installed in combustible enclosure with zeroclearance from the back, side and bottom. A minimum of 6” from the back and sides must bemaintained from the Professional Side Burner...
Page 8 - Standard construction
7 SIDE BURNER BUILT-IN MODEL INSTALLATION 22- 1/8" 2 " 25- 1/2" 10-1/16" 25-1/2" 11- 3/4" 2 " 14 -3/4" Single Side Burner Dual Side Burner Standard construction 12" 10-1/16" 2" X 2" openingfor gas supply line A MODEL A BGB131-BI 12" BGB132-BI 22-3/...
Page 9 - GAS REQUIREMENTS
8 GAS REQUIREMENTS GAS REQUIREMENTS: Verify the type of gas supply to be used, either natural or LP. Make sure the marked gas on the appliance rating plate(s) and hook-up kit agrees with that of the supply. Never connect an unregulated gas line to the appliance. An installer supplied gas shut-off va...
Page 10 - LP TANK REQUIREMENTS
9 GAS REQUIREMENTS LP TANK REQUIREMENTS A dented or rusty LP tank may behazardous and should be checked byyour LP supplier. Never use a cylinderwith a damaged valve. The LP gas cylinder must be constructed and marked in accordance with the specifications forLP gas cylinders of the U.S. Department of...
Page 11 - LEAK TESTING & LIGHTING INSTRUCTIONS; LIGHTING INSTRUCTIONS
10 LEAK TESTING & LIGHTING INSTRUCTIONS WARNING: Do not smoke while leak testing. Extinguish all open flames. Make a soap solution of one part liquiddetergent, and one part water. Never test forleaks with an open flame. For LP units, checkwith a full cylinder. Make sure all control valvesare in ...
Page 12 - MATCH LIGHTING; BURNERS; FLAME HEIGHT
11 LIGHTING INSTRUCTIONS MATCH LIGHTING Hold a fireplace lit match near the burner ports, turn the control knob counterclockwise to “HI”. Moveyour hand immediately once the burner is lit. Rotate the control knob to the desired setting. Note: If you are using propane gas, a slight pop or flash may oc...
Page 13 - FINAL CHECKLIST; PLEASE LEAVE THESE INSTRUCTIONS WITH THE USER.; GENERAL CLEANING; STAINLESS STEEL; DRIP TRAY
12 FINAL CHECKLIST Specified clearances maintained to combustibles. Professional Side Burner is properly mounted. All internal packaging removed. Burner is seated properly and does not rock. Each burner lights satisfactorily, individually or with adjacent burner lit. Knob(s) turn freely. Bezel(s) ce...
Page 14 - GENERAL CLEANING
13 GENERAL CLEANING BURNERS For proper lighting and performancekeep the burners clean. It is necessaryto clean the burners if they do not lighteven though the igniter clicks, if therehas been a severe boil over, or whenthe flame does not burn blue. Be certain all burner knobs are in the offposition ...
Page 15 - TROUBLESHOOTING; PROBLEM
14 TROUBLESHOOTING Burner won’t light when the ignitionis pushed. Burner flame is yellow or orange, inconjunction with the odor of gas. Low heat with knob in “HI” position. Remove the burner grate. With the control knob in the “OFF”position, listen to the electrode while engaging the ignition.You sh...
Page 17 - DOUBLE SIDE BURNER PARTS LIST
16 DOUBLE SIDE BURNER PARTS LIST FOR BGB132 & BGB132-BI NOTE: Part list typical for BGB132 & BGB132-BI models. Illustration shows BGB132-BI model. ITEM DESCRIPTION PART NO. 1 BURNER COVER 33299 2 PULL HANDLE 18204-01 3 RUBBER BUMPER 18403 4 TOP GRATE BK 12013-1 5 D BURNER CAP 12272 6 PORT RI...
Page 18 - SINGLE & DOUBLE SIDE BURNER WIRING DIAGRAM; SINGLE SIDE BURNER
17 SINGLE & DOUBLE SIDE BURNER WIRING DIAGRAM SPARK ELECTRODE(P/N 12224) SPARK ELECTRODE (P/N 12224) SINGLE SIDE BURNER DOUBLE SIDE BURNER 1.5 VOLTALKALINE BATTERYP/N 16567) GND TERMINAL TERMINAL NOTE: HIGH VOLTAGE AT TERMINALS (Switch is built into module) (Switch is built into module) SPARK EL...
Page 19 - WARRANTY; LENGTH OF WARRANTY
18 WARRANTY LENGTH OF WARRANTY DCS warrants all other Side Burner components parts and labor to the original purchaser to be free offactory defects in material and workmanship for a period of one (1) year from the original date ofpurchase. This does not apply if the unit was subjected to other than ...
Page 20 - SERVICE; HOW TO OBTAIN SERVICE:; BEFORE YOU CALL FOR SERVICE:
19 SERVICE HOW TO OBTAIN SERVICE: For warranty service, please contact your local service provider or DCS Customer Care Center at (888) 281-5698, Monday thru Friday, 6 am- 4:30 pm PST. Before you call, please have the followinginformation ready: Model Number (located on the inside of the left side o...
Page 21 - NOTES
