Page 2 - ASHING MACHINE; Co
ASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASH TO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AU ASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER A...
Page 3 - ITEM
1. SPECIFICATIONS 2 SPECIFICATIONS NO. ITEM 1 POWER SOURCE AVAILABLE IN ALL LOCAL AC VOLTAGE 2 POWER 50Hz 320W CONSUMPTION 60Hz 300W(110~127V) / 340W(220V) 3 MACHINE NET WEIGHT GROSS 4 DIMENSION (WXHXD) 5 MATERIAL OF INTERNAL TUB PLASTIC STAINLESS STEEL 6 WATER LEVEL SELECTOR HIGH(55 l ), MID(45 l )...
Page 4 - STRUCTURE OF THE WASHING MACHINE; HOSE ADAPTER; Accessories; NOTE; • Page references are included next to same features.; DRAIN HOSE
2. STRUCTURE OF THE WASHING MACHINE 3 STRUCTURE • GROUND WIRE In case of 3-wire power cord, ground wire will not be provided • POWER CORD • DRAIN HOSE • LINT FILTER • COLD WATER TAP After using the washer, close the water tap • DETERGENT CASE • ADJUSTABLE LEG • SOFTENER INLET • BLEACH INLET • CONTRO...
Page 5 - FUNCTIONS OF THE CONTROL PANEL; • Press this switch to turn the power on or off.
3. FUNCTIONS OF THE CONTROL PANEL 4 CONTROL PANEL • Press this switch to turn the power on or off. • It can be used to choose water temperature to be supplied.• As the button is pressed, water temperature will be repeated. COLD → COLD+HOT → HOT • In case of the single valve model, there is no wash t...
Page 7 - DIRECTIONS FOR INSTALLATION AND USE; Location Of Washer; NOTES; Drain System; In case that it goes over a door sill.; Pump Model
6 4. DIRECTIONS FOR INSTALLATION AND USE DIRECTIONS The opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. § § è Location Of Washer Check location where washer will be installed. Make sure you have everything necessary for correct installation.Prop...
Page 8 - FOR ORDINARY TAP; • Please check the rubber packing; How to Connect the Inlet Hose; • Assert the packing in the inlet
7 CONNECTION FOR ORDINARY TAP 6 Connect the inlet hose adapterof the hose to the water inlet ofthe washer by turning it clock-wise to be fixed tightly. • Please check the rubber packing inside the inlet hose adapter ofthe hose. 1 Pull down the collarof the inlet hose toseparate it from thewater tap ...
Page 9 - How To Clean The Filter; CLEANING THE LINT FILTER; • Clean the filter when water leaks from the water inlet.; CLEANING THE DRAIN FILTER; Turn the cap clockwise tightly.
8 CONVENIENCE § § è How To Clean The Filter 4 Remove the dirtfrom the inlet filterwith a brush. 1 Pull the power plugout beforecleaning it. 2 Turn off thewater supply to the washerand separatethe inlet hose. 3 Pull the inlet filter out. CLEANING THE LINT FILTER CLEANING THE WATER INLET FILTER • Clea...
Page 10 - FEATURE AND TECHNICAL EXPLANATION; WASH DRAIN SPIN FILL RINSE 1 DRAIN SPIN FILL RINSE 2 DRAIN •••; * When the water level is “HIGH”; Feature of the Washing Machine; The first air bubble washing system in the world.; Water Current to Adjust the Unbalanced Load; WATER FLOW; Automatic Water Supply System
9 5. FEATURE AND TECHNICAL EXPLANATION EXPLANATION WASH DRAIN SPIN FILL RINSE 1 DRAIN SPIN FILL RINSE 2 DRAIN ••• MOTOR C.W SINGAL C.C.W TIME(SEC.) 0.4 0.4 0.4 0.4 0.4 0.4 • • • • • • • 40 SEC. (About 25 Times) * When the water level is “HIGH” Feature of the Washing Machine 1 The first air bubble wa...
Page 11 - FUNCTIONAL PRINCIPLE; Automatic Drainning time Adjustment
10 EXPLANATION FUNCTIONAL PRINCIPLE 1 The micom can remember the time from the begining of drain to reset point when the pressure switch reaches to “OFF” point 2 In case of continuous draining, residual drain time is determined by micom. Draining time as a whole = D + 40 Residual drain time.The time...
Page 12 - Softener Dispenser
11 EXPLANATION This is the device to dispense the softener automatically by centrifugal force. This is installed inside the auto-balancer. FUNCTIONAL PRINCIPLE 1 Softener stays in room (A) when poured into softener inlet. 2 Softener moves from (A) to (B) by centrifugal force during intermittent spin...
Page 13 - Automatic Unbalance Adjustment; When the lid is closed, the safety switch contact is “ON” position.
12 EXPLANATION Automatic Unbalance Adjustment Circulating-Water The alarm finished when you close the lid after opening it. Check the unbalance of the wash load and theinstallation condition. NOTES Filter Tub Outer tub Waterchannel Pulsator This system is to prevent abnormal vibration during intermi...
Page 14 - HOW TO REPLACE LINT FILTER; Lint Filter
13 EXPLANATION Much lint may be obtained according to the kind ofclothes to be washed and some of the lint may alsosticks to the clothes.To minimize this possibility a lint filter is provided onthe upper part of the tub to filter the wash water as itis discharged from the water channel. It is good t...
Page 15 - Air; Gear Mechanism Ass’y
14 EXPLANATION The proper water currents is made by the rotation of pulsator at a low speed to prevent the damage to the smallsized clothes. STRUCTURE Pulsator shaft One way clutchbearing Brake lever Spin shaft Gear unit as Clutch spring Clutch boss Gear pulley Planetary gear Sun gear Internal gear ...
Page 16 - PRINCIPLE OF INTAKE & OUTLET OF THE AIR; NS; Air bubble; Functional Principle of Bubble Washing Machine
15 EXPLANATION PRINCIPLE OF INTAKE & OUTLET OF THE AIR INTAKE : ARMATURE moves up, and BELLOWS inhales the air. At the same time, protector B is open and A is close. OUTLET : ARMATURE moves down, and BELLOWS exhausts the air. At the same time, protector B is close and A is opend. FUNCTIONAL PRIN...
Page 17 - DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT; Raise the top plate on the outer cabinet.; Gear Mechanism Ass’y Replacement; NECT THE POWER CORD FROM THE ELECTRIC OUTLET.; Warning
16 DIRECTIONS 6. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT ¡ Raise the top plate on the outer cabinet. ¡ Remove outer tub cover from the tub ass’y. ¡ Remove the spinner shaft flange nut by using ‘T’type box wrench. ¡ Loosen the pulsator mounting screw and removethe pulsator. ¡ Remove the tub ass’y. ...
Page 18 - Lay the front of the washer on the floor.
17 DIRECTIONS ¡ Lay the front of the washer on the floor. ¡ Remove four bolts mounting the plate-gear protect byusing a box wrench and remove plate-gear protect. ¡ Remove the V-belt. ¡ Remove four bolts mounting the gear mechanismass’y by using a box wrench. ¡ Pull out the gear mechanism assy.
Page 19 - Brake Adjustment
18 DIRECTIONS ¡ Loosen the adjustment bolt and turn the adjust-ment bolt until the end of the bolt touches to thebrake lever. ¡ Tighten the lock nut and apply a small amount ofpaint-lock. Adjustment bolt Clutch lever Gear mechanism ass'y Brake lever NOTES: 1. The brake adjustment has been made at th...
Page 20 - THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM; TOOL FOR REPLACING THE CLUTCH BOSS ASSEMBLE; The Structure Of Gear Mechanism
19 THE REPAIR 7. THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM ¡ ¡ ‹ TOOL FOR REPLACING THE CLUTCH BOSS ASSEMBLE ¡ ¡ ‹ Tool name Specification Q’ty Fixing jig 1 Ratchet handle 1 Socket and extension bar socket : 10mm, 17mm per each Some cotton yarn some The Structure Of Gear Mechanis...
Page 21 - PROBLEM; How To Check The Clutch Spring Problem
20 THE REPAIR NO. PARTS NAME SPECIFICATION CODE Q’TY 1 CLUTCH SPRING 1.5*1.5 3615110000 1 2 CLUTCH BOSS PP 3619301300 1 3 GREASE beacon#325 3g PACKING PACKING THE CLUTCH BOSS ASS’Y 1 METHOD BY USING VINYL PACK 1) THE LAUNDARY IS IN THE SPIN TUB UNEVENLY WHEN JUST STARTING SPIN PROCESS. 2) THEREFORE,...
Page 22 - Process; Disassemble 1; Release screws marked 4-point; The Process Of Disassemble
21 THE REPAIR No. Process Notice Disassemble 1 1 2 3 4 Release screws marked 4-point Remove the protector Remove the v-belt Loosen the fastening nut Disassemble the spring washer Use wrench or driver- ratchet handle- extension bar- socket : 10mm Use fixing jig for pulley as tosee fig 1.and 17mm-sock...
Page 23 - Disassemble 2; Disassemble the pulley
22 THE REPAIR No. Process Notice Disassemble 2 5 6 7 8 Disassemble the pulley Disassemble the clutch bossassembly Separate coupling from clutchboss ass’y Cleaning Catch the boss and pullupward with spiral rotate in theclockwise direction Clean the drum plate, couplingsurface and contact facebetween ...
Page 24 - Assemble 1; Assemble the coupling; The Process Of Assemble
23 THE REPAIR No. Process Notice Assemble 1 1 2 3 4 Assemble the coupling Assemble the new clutch bossass’y Assemble the pulley Assemble the spring washer Check the uneven face of cou-pling is assembled upward - Push in the clutch boss ass’ywith rotating on the clockwisedirection.- After assembling,...
Page 25 - Assemble 2; Clutch Tip; Assemble the fastening nut
24 THE REPAIR No. Process Notice Assemble 2 5 6 7 8 Clutch Tip DrainValve Synchronous Motor 3.5~4.5 keep distance 2~3mm Assemble the fastening nut Assemble the Belt Assemble the protector Final checking - Use fixing jig and 17mmsocket wrenchas if disassembling,as fastening torque about100~200kgf-cm....
Page 26 - TROUBLE SHOOTING GUIDE; Concerning Water Supply
8. TROUBLE SHOOTING GUIDE 25 TROUBLE SHOOTING PROBLEM WATER IS NOT SUP- PLIED. CHECK POINT Do you open the water tap? Is the filter of the water inlet valve clogged with dirt? Is the water pressure sufficient? (0.3~8 kgf/cm 2 ) Does the water inlet valve make operating sound? Is the connector or the...
Page 27 - Concerning Washing
26 TROUBLE SHOOTING PROBLEM WATER SUP- PLY IS NOT STOPPED. CHECK POINT Does the water supplycontinue while the poweris turned off? Does the water supply startas soon as you press thepower switch? Operate the washer aftersetting the water level to“HIGH” Does the water supplycontinue after the waterre...
Page 28 - Concerning Draining
27 TROUBLE SHOOTING PROBLEM THE WASHER DOES NOT DRAIN. CHECK POINT Do you install thedrain hose properly? Is the foreign matteraccumulated insidethe pump housing? Is the output voltage ofthe drain pump normal? CAUSE SOLUTION Install the drain hoseproperly. Remove the foreign mat-ter from the pump ho...
Page 29 - YES; Concerning Spinning
28 TROUBLE SHOOTING PROBLEM THE WASHER DOES NOT SPIN. CHECK POINT Is the lid open? Does the safety switchoperate normally? Does the pulsator rotatewhile the tub does notrotate? Is the connector ofP.C.B ASS‘Y connectedproperly? Is the input voltage of the drainmotor normal? Is the V-belt worn out? Is...
Page 30 - Concerning Operation
29 TROUBLE SHOOTING NO NO PROBLEM THE INDICA- TOR LAMPS(L.E.D) DO NOT LIGHT UP WHEN THE POWER BUT- TON IS PRESSED. PROGRESSLAMPS(LED)DO NOT LIGHTUP. MOTORROTATESWHENSTART/HOLDBUTTON ISNOTPRESSED. ABNORMALNOISE DUR-ING WASHPROCESS. CHECK POINT Is the plug connect-edto electric outlet? Is the conditio...
Page 31 - MESSAGE CAUSE SOLUTION; Concerning Error Message
9. PRESENTATION OF THE P.C.B ASS’Y 30 PCB ASS’Y MESSAGE CAUSE SOLUTION Improper installation of drain hose. The drain hose is blocked up by foreign matter. Drain motor is inferior. The water tap is closed. The water inlet filter clogged. It passes over the 30 minutes, yet it doesn’t come to assigned...
Page 32 - APPENDIX
APPENDIX 31 WIRING DIAGRAM § § è Wiring Diagram [non-pump]
Page 36 - Parts Diagram
Page 37 - Parts List; PART NAME
36 PARTS DIAGRAM §§ è Parts List NO. PART NAME PART CODE SPECIFICATION REMARK A01 PLATE T 3614521500 PP A02 DOOR B AS 3611797600 ABS OPTION : A03 DOOR F AS 3611797700 ABS TRANSPARENT A04 DOOR B 3611797300 PP OPTION : A05 DOOR F 3611797400 PP NOT TRANSPARENT A06 SPRING PLATE LEVER 3615111800 SUS A07 ...
Page 45 - Circuit Diagram
44 CIRCUIT DIAGRAM § § è Circuit Diagram 1. DWF-750/752/803/805/753/755/803/805
