Dacor IF42BNDB - Manual

PLANNING

GUIDE

Web: http://www.Dacor.com

Corporate Phone: 800-793-0093

Specifications are subject to change without notice.

See installation instructions for additional details.

11.2

42” & 48” wide

built-In refrigerator

Ef42bDCb, Ef42bNDb, If42bDCb, If42bNDb,

Ef48bDCb, Ef48bNDb, If48bDCb, If48bNDb

112905

1/3

Model

Rough-In Width “A”

42-Inch

41 1/2”” (1054mm)

48-Inch

47 1/2”” (1207mm)

D

oor

s

winG

D

imEnsions

The area to the left and the right of the appliance must permit

both doors to open to a minimum of 90°. Allow a minimum of 2

1/2” (64mm) space between the side of the refrigerator doors and

a corner wall.

NOTE:

More clearance may be required if using an overlay panel

or custom handles.

p

roDuct

D

imEnsions

◊

The depth from the front of the top grill (w/o decorator panel)

to the back of the refrigerator chassis is 25 1/4” (641mm).

◊

The depth from the rear of the top grill to the back of the

refrigerator chassis is 23 13/16” (605mm).

◊

The power cord is 40” (1016mm) long.

◊

The height from the top of the top grill to floor with the

leveling legs in the down position is 83 3/8” (2118mm)

◊

The height from the top of the top grill to floor with the

leveling legs in the fully extended position is 84 5/8”

(2149mm)

◊

The chassis width from the chassis edge to the chassis edge

for 42-inch is model 41 1/4” (1048mm), 48-inch is model 47

1/4” (1200mm).

◊

The overall width from the trim edge to the trim edge for 42-

inch model is 42 1/16” (1068mm), 48-inch model is 48 1/16”

(1221mm).

E

lEctrical

r

EquirEmEnts

A 115VAC, 60 Hz, 15 Amp circuit breaker and electrical supply are

required. A separate dedicated non-GFCI circuit, servicing only

this appliance, is required.

Your Dacor

®

Built-In refrigerator is equipped with a 40” (1016mm)

3-prong grounded power cord, which must be plugged into a

3-prong grounding-type non-GFCI wall receptacle. Follow the

National Electrical Code and local codes and ordinances when

installing the receptacle. See “Rough-In Dimensions” for location

of the electrical supply.

IMPORTANT:

A ground fault circuit interrupter (GFCI) is not

recommended and may cause interruption of operation.

◊

All installations must meet local plumbing code

requirements.

◊

Connect to 1/4” (6mm) copper line to the house cold fresh

water supply.

◊

Use a shut off valve between the refrigerator and supply.

The shut off valve should be a drilled saddle valve.

◊

Do not use a self-tapping valve which reduces water flow

and clogs more easily.

◊

Route the water line within 3-1/2” (89mm) of the rear wall

and no higher than 3” (76mm) from the floor.

◊

Allow a minimum of 24” (610mm) dimeter service loop of

copper tubing outside the wall or floor for easy connection to

the water supply.

Cold water supply

Connect the ice maker to a cold water line with water pressure

between 30 and 120 PSI. If you have any questions about your

water pressure, call your utility company.

IMPORTANT:

◊

In homes with a Reverse Osmosis water treatment system,

remove the water inlet connector from the “yellow” valve

and attached to the “blue” valve. Make sure the water filter

bypass plug is in place.

w

atEr

s

upply

r

EquirEmEnts

7”

4”

2”

6”

3”

75 1/2”

“A”

83 3/4”

Water Supply

Electrical

24”