Dacor IF36BNDFSF - Manual
Dacor IF36BNDFSF – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – IF36 Panel Overlay Installation; NOTE; : Modification to the dimensions above may be required to allow for; No Trim
- Page 4 – andle; Detail “C”
- Page 5 – anel; With a Phillips screwdriver, remove the trim screws from the; Two door models; Freezer Door; Right door
- Page 6 – oteS
I
ntroductIon
Custom decorator panels cover the door trim of Dacor IF36 series refrigerators for an attractive
seamless look that flows into the overall design of the room. Fabricate the panels first, then slide
them into the door trim frames. The panels are custom designed and installed by your cabinet
maker.
Installation may be accomplished using various methods. Below are three examples.
For additional installation ideas, see the 3-Door Custom Overlay Installation Guide (PN 102426).
Three Panel Method
The backing panel (1/4” [6 mm] thick) slides behind the trim frames that surround the edges of
each door. The spacer (1/8” [3 mm] thick) compensates for the thickness of the trim frame. The
decorative front panels (3/4” [19 mm] thick maximum) are designed to match the surrounding
cabinets and cover the trim frame around the edges of the door. Countersink the screws used to
assemble the panels.
WARNING:
Individual door panels must not exceed the maximum weight specifications.
CUSTOM OVERLAY PANEL
INSTALLATION
INSTRUCTIONS
REFRIGERATOR MODELS: IF36BNDFSF, IF36INDFSF
Part No. 100504 Rev. F
Routed Raised Panel Method
Create a routed raised panel and screw or glue the front panel directly to the 1/4” thick backing
panel. Instead of using a spacer panel, route the edges of the front panel to compensate for the
trim frame thickness. For the top two doors on three door models, do not route the inner edges
because there are no trim frames in the center where the doors come together. Countersink the
screws used to assemble the panels.
Spacer Panel (1/8”)
Refrigerator Door
Front Panel (3/4” Max.)
Backing Panel (1/4”)
Trim Frame
Surrounding Door
Backing Panel (1/4”)
Refrigerator Door
Front Panel (7/8” Max.)
Routed Area
(1/4” W X 1/8” D)
Trim Frame
Surrounding Door
Single Panel Method
A single 1/4” panel design can be created using the trim
frames to frame the panel (the trim frames will be exposed).
Single 1/4” Panel
Trim Frame Surrounding Door
Refrigerator Door
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Dacor IF36BNDFSF
Summary
IF36 Panel Overlay Installation Page 2 B A C D D D Three Door Model Two Door Model P anel S PecIfIcatIonS Front Panels NOTE : Modification to the dimensions above may be required to allow for door swing and other considerations depending on the location and type of cabinet installation. Backing Pane...
IF36 Panel Overlay Installation Page 4 h andle d IMenSIonS and I nStallatIon Before installing a custom panel assembly, you must install • the custom handle hardware. Dacor recommends handles with larger D-style pulls. If using • screws with thick heads, they must be countersunk into the panel befor...
IF36 Panel Overlay Installation Page 5 P anel I nStallatIon NOTE : Remove the top door(s) to make panel installation easier. On three door models secure the inner edges of the overlays to the door where there are no trim frames using double sided tape. With a Phillips screwdriver, remove the trim sc...
