Page 2 - ABOUT THIS GUIDE; LED I
i T A B L E O F C O N T E N T S ABOUT THIS GUIDE ....................................................1 P URPOSE .........................................................................................1 O VERVIEW OF THIS U SER ’ S G UIDE ..........................................1 INTRODUCTION ........
Page 3 - ii; A. Using straight cable; RJ-45 PIN SPECIFICATION
ii DSS-8+ TO SWITCH ( OTHER DEVICES ) ..................................11 A. Using straight cable .............................................................12 B. Using crossover cable .........................................................12 P ORT S PEED & D UPLEX M ODE ......................
Page 4 - Purpose; Introduction
1 A B O U T T H I S G U I D E Congratulations on your purchase of the DSS-8+. This device integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible desktop package. Purpose The purpose of this manual is to show you how to install and configure your DSS-8+. Overvi...
Page 5 - N T R O D U C T I O N; Fast Ethernet Technology
2 I N T R O D U C T I O N This chapter describes the features of the DSS-8+ and some background information about Ethernet/Fast Ethernet switching technology. Fast Ethernet Technology The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need ...
Page 7 - Features
4 Features The DSS-8+ was designed for easy installation and high performance in an environment where traffic on the network and the number of users increase continuously. The DSS-8+ with its small, compact size was specifically designed for small to middle workgroups. The DSS-8+ can be installed wh...
Page 9 - Unpacking and Setup; Unpacking; One external power adapter; Setup; The setup for the DSS-8+ can be performed using the following steps:
6 Unpacking and Setup This chapter provides unpacking and setup information for the DSS-8+. Unpacking Open the box and carefully unpacks its contents. The box should contain the following items: ♦ One DSS-8+ ♦ One external power adapter ♦ One pair of Stacking Brackets ♦ This User’s Guide. If any ite...
Page 10 - Front Panel; LED Indicator Panel; LED Indicators; This LED indicator lights green when a respective port is in full
7 I D E N T I F Y I N G E X T E R N A L C O M P O N E N T S This section identifies all the major external components of the DSS-8+. Both the front and rear panels are shown followed by a description of each panel feature. The indicator panel is described in detail in the next chapter. Front Panel T...
Page 11 - Rear Panel; Power is supplied through an external AC power
8 duplex (FDX) mode. Otherwise, it is blinking when collisions are occurring on the respective port. 100M Link/Activity, 10M Link/Activity (100M LINK/ACT (green) , 10LINK/ACT (amber) ) This indicator lights green when the port is connected to a 100Mbps Fast Ethernet station, if the indicator blinkin...
Page 12 - Use this jack to connect stations to the; MDI; port using an ordinary straight-through cable, making a
9 another hub or an Ethernet switch, you should use a crossover cable, or make the connection using the MDI-X jack (described below). ♦ Uplink Jack(s) (MDI-II): Use this jack to connect stations to the hub. This is an MDI - II (Medium-dependent Interface, straight- wired) jack, which means you can c...
Page 13 - LAN card capabilities for full duplex or half duplex.
10 C O N N E C T I N G T H E D S S - 8 + This chapter describes how to connect the DSS-8+ to your Fast Ethernet network. In each of the following figures, the DSS-8+ is shown. PC to DSS-8+ A PC can be connected to DSS-8+ via a two-pair Category 3, 4, 5 UTP/STP straight cable. The PC (equipped with a...
Page 14 - “Full-Duplex/Collision” LED indicator is
11 A. 10BASE-T Hub For a 10BASE-T hub, the DSS-8+ LED indicators should light up as the following: “Full-Duplex/Collision” indicator is OFF. “100LINK/ACT,10LINK/ACT LED” indicator is light amber. B. 100BASE-TX Hub For a 100BASE-TX hub, the DSS-8+ LED indicators should light up as the following: “Ful...
Page 15 - Port Speed & Duplex Mode
12 A. Using straight cable When using straight cable, this is done from the uplink (MDI-II) port of the DSS-8+ (DSS-8+ A) to any of the 10Mbps or 100Mbps (MDI-X) port of the other switch (switch B) or other devices. B. Using crossover cable When using crossover cable, this is done from any (MDI-X) p...
Page 16 - The brackets are now ready for stacking devices. See the diagram
I N S T R U C T I O N S F O R U S E O F S T A C K I N G B R A C K E T S First, make sure you have one pair of stacking brackets for each device. Next, slide one bracket onto each end of the device as shown in the diagram below. Be sure each bracket is positioned correctly. Note when clicking each br...
Page 17 - The standard cable, RJ-45 pin assignment
14 R J - 4 5 P I N S P E C I F I C AT I O N When connecting your DSS-8+ to another switch, a bridge or a hub, a modified crossover cable is necessary. Please review these products for matching cable pin assignment. The following diagram and tables show the standard RJ-45 receptacle/connector and the...
Page 18 - other devices connection
15 The standard RJ-45 receptacle/connector The following shows straight cable and crossover cable connection: Straight cable for DSS-8+ (uplink MDI-II port) to switch/Hub or other devices connection Crossover cable for DSS-8+ (MDI-X port) to switch/hub or other network devices (MDI-X port) connectio...
Page 19 - General
16 T E C H N I C A L S P E C I F I C AT I O N S General Standards IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet ANSI/IEEE Std. 802.3 NWay Auto-negotiation Protocol CSMA/CD Data Transfer Rate Ethernet: 10Mbps (half duplex) , 20Mbps (full-duplex) Fast Ethernet: 100Mbps (half duplex...
Page 21 - FCC Certifications; VCCI Warning
FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, u...
Page 22 - LIMITED WARRANTY
LIMITED WARRANTY D-Link provides this limited warranty for its product only to the person or entity who originally purchased the product from D-Link or its authorized reseller or distributor. Limited Hardware Warranty: D-Link warrants that the hardware portion of the D-Link products described below ...
Page 26 - Trademarks; Copyright Statement; No part of this publication may be reproduced in any form or
Trademarks Copyright 1999 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement No part of this publication may be reproduced ...
