Page 2 - FCC Warning; CE Mark Warning
DSL-360T DSL Modem User’s Guide ii FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may caus...
Page 3 - LIMITATION OF LIABILITY; Limited Warranty
DSL-360T ADSL Modem User’s Guide iii LIMITATION OF LIABILITY IN NO EVENT WILL D-LINK BE LIABLE FOR ANY DAMAGES, INCLUDING LOSS OF DATA, LOSS OF PROFITS, COST OF COVER OR OTHER INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE OR INTERR...
Page 4 - TABLE OF CONTENTS
TABLE OF CONTENTS About This User’s Guide .............................................................................................................................. vii Before You Start .................................................................................................................
Page 7 - About This User’s Guide; Quick Installation Guide; Before You Start; Installation Overview
DSL-360T DSL Modem User’s Guide vii About This User’s Guide This user’s guide provides instructions on how to install the DSL-360T ADSL Modem and use it to connect a computer or Ethernet Local Area Network (LAN) to the Internet thus providing a gateway to the Wide Area Network (WAN). If you are usin...
Page 8 - Information Required for Installation; Information you will need from your ADSL service provider:; Information you will need to change settings on the DSL-360T Modem:
DSL-360T DSL Modem User’s Guide viii Information Required for Installation Information you will need from your ADSL service provider: Username This is the Username used to log on to your ADSL service provider’s network. It is commonly in the form − [email protected]. Your ADSL service provider uses this ...
Page 9 - Information you will need about your Ethernet LAN or computer:; Ethernet NIC; DHCP Client status; Obtain an IP address automatically; Note
DSL-360T DSL Modem User’s Guide ix Information you will need about your Ethernet LAN or computer: Ethernet NIC If your computer has an Ethernet NIC, you can connect the DSL-360T to this Ethernet port using an Ethernet cable. You can also use the Ethernet port on the DSL-360T to connect to other Ethe...
Page 11 - Introduction; Modem Description and Operation; Low Pass Filters
DSL-360T ADSL Modem User’s Guide 1 1 Introduction This section provides a brief description of the Modem, its associated technologies and a list of Modem features. Modem Description and Operation The DSL-360T ADSL Modem is designed to provide a simple and cost-effective ADSL Internet connection for ...
Page 12 - Web Browser
DSL-360T ADSL Modem User’s Guide 2 Web Browser Any common web browser can be used to configure the Modem using the web configuration management software. The program is designed to work best with more recently released browsers such as Opera, Microsoft Internet Explorer® version 5.0, Netscape Naviga...
Page 13 - Modem Features; DHCP Support; Precise ATM Traffic Shaping –; High Performance –
DSL-360T ADSL Modem User’s Guide 3 Modem Features The DSL-360T ADSL Modem utilizes the latest ADSL enhancements to provide a reliable Internet portal suitable for most small to medium sized offices. DSL-360T advantages include: • PPP (Point-to-Point Protocol) Security – The DSL-360T ADSL Modem suppo...
Page 14 - Standards Compatibility and Compliance
DSL-360T ADSL Modem User’s Guide 4 Standards Compatibility and Compliance The DSL-360T complies with or is compatible with the following standards as recognized by their respective agencies. • ITU G.992.2 (G.lite “Splitterless ADSL”) compliant • ITU-T Rec. I.361 compliant • RFC 791 Internet Protocol...
Page 15 - Packing List; Front Panel Display; Power
DSL-360T ADSL Modem User’s Guide 5 Packing List Open the shipping carton and carefully remove all items. In addition to this User's Guide, ascertain that you have: • One DSL-360T ADSL Modem • One Quick Installation Guide • One twisted-pair telephone cable used for ADSL connection • One straight-thro...
Page 16 - Rear Panel Connections
DSL-360T ADSL Modem User’s Guide 6 Rear Panel Connections All cable connections to the Modem are made at the rear panel. Connect the power adapter here to power on the Modem. Use the Reset button to restore the settings to the factory default values (see Factory Reset Button in the next chapter for ...
Page 17 - Hardware Installation; Power on Modem; Factory Reset Button; admin
DSL-360T ADSL Modem User’s Guide 7 2 Hardware Installation The DSL-360T maintains two interfaces and provides a bridge between two networks. An Ethernet port connects to a computer or Ethernet LAN and an ADSL port provides the connection to the Internet and the Wide Area Network. Place the Modem in ...
Page 18 - Network Connections; Connect ADSL Line; Computer to Modem Connection
DSL-360T ADSL Modem User’s Guide 8 Network Connections Network connections are provided through the ADSL port and the Ethernet port on the back of the Modem. See the Rear Panel diagram above and the illustrations below for examples. Connect ADSL Line Use the ADSL cable included with the Modem to con...
Page 19 - Hub or Switch to Modem Connection
DSL-360T ADSL Modem User’s Guide 9 Hub or Switch to Modem Connection Connect the Modem to an uplink port (MDI-II) on an Ethernet hub or switch with a straight-through cable as shown in the diagram below: If you wish to reserve theuplink port on the switch orhub for another device,connect to any on t...
Page 20 - Configuring the Modem for the First Time; Wan Configuration Summary; Connect to the Modem; Configuring IP Settings on Your Computer
DSL-360T ADSL Modem User’s Guide 10 3 Configuring the Modem for the First Time The first time you setup the Modem, configure the WAN connection using a single computer connected directly to the Modem. Once the WAN connection is functioning properly, you may continue to make changes to Modem configur...
Page 21 - Configure Windows XP for DHCP
DSL-360T ADSL Modem User’s Guide 11 Configure Windows XP for DHCP Use the following steps to configure a computer running Windows XP to be a DHCP client. 1. From the Start menu on your desktop, go to Settings , then click on Network Connections . 2. In the Network Connections window, right-click on ...
Page 22 - General; Local Area Connection Properties
DSL-360T ADSL Modem User’s Guide 12 3. In the General tab of the Local Area Connection Properties menu, highlight Internet Protocol (TCP/IP) under “This connection uses the following items:” by clicking on it once. Click on the Properties button.
Page 23 - Configure Windows 2000 for DHCP
DSL-360T ADSL Modem User’s Guide 13 4. Select “Obtain an IP address automatically” by clicking once in the circle. Click the OK button. Your computer is now ready to use the Modem’s DHCP server. Windows 2000 First, check for the IP protocol and, if necessary, install it: 1. In the Windows task bar, ...
Page 24 - Windows ME; Configure Windows ME for DHCP
DSL-360T ADSL Modem User’s Guide 14 4. In the Internet Protocol (TCP/IP) Properties dialog box, click the button labeled Obtain an IP address automatically . 5. Double-click OK to confirm and save your changes, and then close the Control Panel. Your computer is now ready to use the Modem’s DHCP serv...
Page 25 - Configure Windows 95 and Windows 98 for DHCP; Access the Configuration Manager
DSL-360T ADSL Modem User’s Guide 15 Configure Windows 95 and Windows 98 for DHCP 1. Open the Control Panel window, and then click the Network icon. 2. Select the network component labeled TCP/IP, and then click Properties . 3. If you have multiple TCP/IP listings, select the listing associated with ...
Page 26 - Home
DSL-360T ADSL Modem User’s Guide 16 To use the web-based management software, launch a suitable web browser and direct it to the IP address of the Modem. Type in http:// followed by the default IP address, 192.168.1.1 in the address bar of the browser. The URL in the address bar should read: http://...
Page 27 - Configure the Modem; Figure 3-2. Home – Status Information window
DSL-360T ADSL Modem User’s Guide 17 Configure the Modem The first page that appears after you successfully login displays information about the Modem and its connection status. Tabs across the top of the screen show other available menus: Home , Setup , Tools , Status , and Help . Figure 3-2. Home –...
Page 28 - Setup
DSL-360T ADSL Modem User’s Guide 18 Setup The Setup window offers links to menus to configure settings for the LAN (Local Area Network) and for the WAN (Wide Area Network) setup. The first menu you see when clicking the Setup tab is the Modem Setup menu. All the information you need to make the chan...
Page 29 - Configure a New Connection; Connection; PPoA
DSL-360T ADSL Modem User’s Guide 19 Configure a New Connection The default connection protocol used for the Modem is Point-to-Point Protocol over ATM (PPPoA). The menu used to configure ADSL service using this protocol is the menu you see when clicking on the Connection button under WAN Setup on the...
Page 31 - Change
DSL-360T ADSL Modem User’s Guide 21 PPPoE The required information used to setup a PPPoE connection is identical to that needed for a PPPoA connection. Make sure you have selected PPPoE from the Type: pull-down menu so that you are now configuring setting in the menu titled “PPPoE Connection Setup”....
Page 32 - Bridge
DSL-360T ADSL Modem User’s Guide 22 7. The Encapsulation values LLC (SNAP) and VC (MUX) are two different methods of encapsulating the PPP packet. Contact your ISP to make sure which encapsulation is being supported. 8. For most users, the remaining settings will not need to be changed. See your ISP...
Page 33 - CLIP
DSL-360T ADSL Modem User’s Guide 23 “Bridge” means a pure bridged connection with no IP address assigned to the Modem. This connection method makes the Modem act as a bridge, and just passes packets across the DSL port. 1. Type in a Name in the space provided if you wish or leave the default name. 2...
Page 35 - Web-based Management; Accessing the Web Manager
DSL-360T ADSL Modem User’s Guide 25 4 Web-based Management The DSL-360T offers a web-based (HTML) graphical user interface allowing users to manage the Modem from anywhere on the LAN using a standard browser. A web browser is used to communicate directly with the Modem and make changes to the config...
Page 36 - DHCP Configuration; Figure 4-1. Setup – DHCP Configuration window; End IP
DSL-360T ADSL Modem User’s Guide 26 DHCP Configuration Use the DHCP Configuration window to configure the Modem to act as a DHCP server for the LAN. Figure 4-1. Setup – DHCP Configuration window Configure LAN DHCP services by defining the following parameters: Start IP Type in the base address for t...
Page 37 - Management IP; Figure 4-2. Setup – Management IP window
DSL-360T ADSL Modem User’s Guide 27 Management IP The IP address of the modem may be changed, but remember to take note of the new settings. A valid IP address and subnet mask are needed to access the Web manager. Figure 4-2. Setup – Management IP window Make any desired changes, then, click Apply .
Page 38 - Changing the User Name and Password; Tools; Tools; User Management
DSL-360T ADSL Modem User’s Guide 28 Tools Changing the User Name and Password Before you configure the Modem and connect to the WAN, you should change the user name and password used to access the web-based manager. Click on the Tools tab to access the Tools menu. Figure 4-3. Opening Tools window Th...
Page 39 - Figure 4-4. Tools – User Management window; User Name; Password; Confirm Password
DSL-360T ADSL Modem User’s Guide 29 User Management Use this menu to change the user name and password used to gain management access to the Modem. Figure 4-4. Tools – User Management window 1. Type the current User Name in the entry field provided. 2. Type in the new Password in the entry field pro...
Page 40 - Figure 4-5. Tools – System Commands window; Save All; Restart; Restart; Restore
DSL-360T ADSL Modem User’s Guide 30 System Commands These menu options are used to save setting, restart (reboot) the Modem or reset the configuration to the factory settings. Figure 4-5. Tools – System Commands window Save All In order to save the configuration changes you have just made they must ...
Page 41 - Remote Log; Add an IP Address
DSL-360T ADSL Modem User’s Guide 31 Remote Log Use this menu to designate receiver stations for event messages form the Modem. Figure 4-6. Tools – Remote Log window To set up a destination for event messages: 1 Select the Log Level form the pull-down list. 2 Add and IP address of a server or station...
Page 42 - Update Gateway; Figure 4-7. Tools – Update Gateway window
DSL-360T ADSL Modem User’s Guide 32 Update Gateway Figure 4-7. Tools – Update Gateway window Use the Update Gateway feature to load the latest firmware for the device. You can obtain the latest version of the DSL-360T firmware by logging onto the D-Link web site at www.dlink.com . Save the latest fi...
Page 43 - Ping Test; Test
DSL-360T ADSL Modem User’s Guide 33 Ping Test Figure 4-8. Tools – Ping Test window This window is used to test the connection path of the Modem to another networked device with an IP address. To Ping a device, first enter the IP address of the device that you wish to Ping into the first field, the P...
Page 44 - Modem Test
DSL-360T ADSL Modem User’s Guide 34 Modem Test The Modem Test menu is used to check connectivity of the ADSL connection via the ATM network. This is similar to a Ping test except it is testing the ATM network instead of the IP network. Figure 4-9. Tools – Modem Test window To test your modem, select...
Page 45 - Status
DSL-360T ADSL Modem User’s Guide 35 Status Figure 4-10. Opening Status window Click the hyperlink for the desired Status window.
Page 46 - Network Statistics; Figure 4-11. Status – Network Statistics window
DSL-360T ADSL Modem User’s Guide 36 Network Statistics Figure 4-11. Status – Network Statistics window Choose the desired interface at the top of the window and then click Refresh to view Ethernet network statistics.
Page 47 - Connection Status; Figure 4-12. Status – Connection Status window; Refresh
DSL-360T ADSL Modem User’s Guide 37 Connection Status Figure 4-12. Status – Connection Status window Click Refresh to view connection status information.
Page 48 - DHCP Clients; Figure 4-13. Status – DHCP Clients window
DSL-360T ADSL Modem User’s Guide 38 DHCP Clients Figure 4-13. Status – DHCP Clients window This window displays the status of all current DHCP clients.
Page 49 - Modem Status; Figure 4-14. Status – Modem Status window
DSL-360T ADSL Modem User’s Guide 39 Modem Status Figure 4-14. Status – Modem Status window This window displays the status of the modem as well as DSL statistics.
Page 51 - System Log
DSL-360T ADSL Modem User’s Guide 41 System Log Figure 4-16. Status – System Log window Click Refresh to get the most current system log information.
Page 52 - Help
DSL-360T ADSL Modem User’s Guide 42 Help Figure 4-17. Opening Help window Click on the item you want further information for on the window above.
Page 53 - Technical Specifications; GENERAL
DSL-360T ADSL Modem User’s Guide 43 A Technical Specifications GENERAL Standards: ITU G.992.1 (G.dmt) ITU G.992.2 (G.lite) ITU G.994.1 (G.Hs) ITU-T Rec. I.361 ITU-T Rec. I.610 IEEE 802.3 IEEE 802.3u IEEE 802.1d RFC 1213 compliant RFC 1483 (Bridged Ethernet) RFC 1577 (IP over ATM) RFC 1661 (PPP) RFC ...
Page 54 - Physical and Environmental
DSL-360T ADSL Modem User’s Guide 44 Physical and Environmental DC Inputs: Power Adapter: Input: 100V ~ 240V AC 50 ~ 60Hz Output: 9V AC, 1A Power Consumption: 3 Watts (max) Operating Temperature: 5° to 40° C (41° - 104° F) Humidity: 5 to 95% (non-condensing) Dimensions: 142 (W) x 117(D) x 31(H) mm We...
Page 55 - IP Address Setup; Assigning Network IP Addresses; Start; Control Panel; Using Default IP without DHCP
DSL-360T ADSL Modem User’s Guide 45 B IP Address Setup The DSL-360T is designed to provide network administrators maximum flexibility for IP addressing on the Ethernet LAN. The easiest IP setup choice in most cases is to let the Modem do it using DHCP, which is enabled by default. This appendix brie...
Page 56 - Using DHCP; Alternative IP Assignment
DSL-360T ADSL Modem User’s Guide 46 network IP address (all machines must belong to the same IP network), while the last number denotes the host IP address (each computer must have a unique address to distinguish it on the network). The IP address scheme used in Example #1 can be used for any LAN th...
Page 57 - IP Concepts; IP Addresses
DSL-360T ADSL Modem User’s Guide 47 C IP Concepts This appendix describes some basic IP concepts, the TCP/IP addressing scheme and show how to assign IP Addresses. When setting up the Modem, you must make sure it has a valid IP address. Even if you will not use the WAN port (ADSL port), you should, ...
Page 58 - IP Network Classes; network number; host number
DSL-360T ADSL Modem User’s Guide 48 Networks attached to the Internet are assigned class types that determine the maximum number of possible hosts per network. The previous figure illustrates how the net and host portions of the IP address differ among the three classes. Class A is assigned to netwo...
Page 59 - Subnet Mask; IP Class
DSL-360T ADSL Modem User’s Guide 49 Subnet Mask In the absence of subnetworks, standard TCP/IP addressing may be used by specifying subnet masks as shown below. IP Class Subnet Mask Class A 255.0.0.0 Class B 255.255.0.0 Class C 255.255.255.0 Subnet mask settings other than those listed above add sig...
Page 60 - Microfilters and Splitters; Microfilters
DSL-360T ADSL Modem User’s Guide 50 D Microfilters and Splitters Most ADSL clients will be required to install a simple device that prevents the ADSL line from interfering with regular telephone services. These devices are commonly referred to as microfilters or sometimes called (inaccurately) line ...
Page 61 - Line Splitter; Line; ADSL; Phone; Line Splitter Installation
DSL-360T ADSL Modem User’s Guide 51 Line Splitter If you are instructed to use a “line splitter”, you must install the device between the Modem and the phone jack. Use standard telephone cable with standard RJ-11 connectors. The splitter has three RJ-11 ports used to connect to the wall jack, the Mo...
Page 63 - Offices
Offices Australia D-Link Australia 1 Giffnock Avenue, North Ryde, NSW 2113, Sydney, Australia TEL: 61-2-8899-1800 FAX: 61-2-8899-1868 TOLL FREE (Australia): 1800-177100 URL: www.dlink.com.au E-MAIL: [email protected] & [email protected] Brazil D-Link Brasil Ltda. Edificio Manoel Tabacow Hydal...
Page 66 - Registration Card
Registration Card Print, type or use block letters. Your name: Mr./Ms__________________________________________________________________________ Organization: ____________________________________________Dept.______________________________ Your title at organization:___________________________________...
