D-Link DGS-1008T - Manual - manualsarea.com

Page 3 - Terms; Introduction

A B O U T T H I S G U I D E This user’s guide tells you how to install your 8-Port 10/100/1000Mbps Gigabit Ethernet Switch, how to connect it to your Gigabit Ethernet network. Terms For simplicity, this documentation uses the terms “Switch” (first letter upper case) to refer to the 8-Port 10/100/100...

Page 4 - N T R O D U C T I O N; This; Gigabit Ethernet Technology; environments, Gigabit Ethernet provides a

I N T R O D U C T I O N This section describes the features of the 8-Port 10/100/1000Mbps Gigabit Ethernet Switch, as well as giving some background information about Gigabit Ethernet and switching technology. Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utiliz...

Page 5 - Switching Technology; segments

Gigabit Ethernet supports video conferencing, complex imaging, and similar data-intensive applications. Likewise, since data transfers occur 10 times faster than Fast Ethernet, servers outfitted with Gigabit Ethernet NIC’s are able to perform 10 times the number of operations in the same amount of t...

Page 6 - Features

Switching LAN technology is a marked improvement over the previous generation of network bridges, which were characterized by higher latencies. Routers have also been used to segment local area networks, but the cost of a router and the setup and maintenance required make routers relatively impracti...

Page 7 - Unpacking; Accessory pack: 2 mounting brackets and screws; Setup; The surface must support at least 5 kg.

U N P A C K I N G A N D S E T U P This chapter provides unpacking and setup information for the Switch. Unpacking Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items: ♦ One 8-Port 10/100/1000Mbps Gigabit Ethernet Switch ♦ Accessory ...

Page 8 - Desktop or Shelf Installation

♦ Visually inspect the power cord and see that it is secured fully to the AC power connector. ♦ Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Do not place heavy objects on the Switch. Desktop or Shelf Installation When installing the Switch on a des...

Page 9 - Rack Installation

Rack Installation The Switch can be mounted in an EIA standard size, 19-inch rack, which can be placed in a wiring closet with other equipment. To install, attach the mounting brackets on the switch’s front panel (one on each side) and secure them with the screws provided. A t t a c h i n g t h e m ...

Page 10 - Front Panel; LED Indicators; Rear Panel

I D E N T I F Y I N G E X T E R N A L C O M P O N E N T S This chapter describes the front panel, rear panel and LED indicators of the Switch Front Panel The front panel of the Switch consists of 8 1000BASE-T ports and LED indicators. Front panel view of the Switch ♦ Eight Gigabit Ethernet ports of ...

Page 11 - AC Power Connector; This is a three-pronged connector

R e a r p a n e l v i e w o f t h e S w i t c h ♦ AC Power Connector This is a three-pronged connector that supports the power cord. Plug in the female connector of the provided power cord into this connector, and the male into a power outlet. Supported input voltages range from 100 ~ 240 VAC at 50 ...

Page 12 - Power; This indicator lights green when the Switch is

Per unit: ♦ Power This indicator lights green when the Switch is receiving power, otherwise, it is off. Per port: ♦ 1000M LINK/ACT . These LED indicators are lit when there is a secure connection (or link) to 1000Mbps Gigabit Ethernet device at any of the ports. The LED indicators blink whenever the...

Page 13 - General

T E C H N I C A L S P E C I F I C A T I O N S General Standards: IEEE 802.3ab 1000BASE -T IEEE 802.3u 100BASE -T X IEEE 802.3 10BASE -T Protocol: CSMA/CD Data Transfer Rate: 10Mbps (Half-duplex) E t h e r n e t : 20Mbps (Full-duplex) 100Mbps (Half-duplex) Fast Ethernet: 200Mbps (Full-duplex) Gigabit...

D-Link DGS-1008T - Manual

Table of Contents:

Summary

Other D-Link Models