Page 2 - Wichtige Sicherheitshinweise; Limited Warranty
Wichtige Sicherheitshinweise 1. Bitte lesen Sie sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den spätern Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oderAerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur...
Page 4 - D-Link Offices for Registration and Warranty Service
D-Link warrants that its software products will perform in substantial conformance with the applicable productdocumentation provided by D-Link with such software product, for a period of ninety (90) days from the date ofpurchase from D-Link or its Authorized Reseller. D-Link warrants the magnetic me...
Page 7 - ABLE OF
Introduction vii T ABLE OF C ONTENTS 0 ABOUT THIS GUIDE ............................................................................. ix P URPOSE ...................................................................................................... ix T ERMS /U SAGE ....................................
Page 9 - BOUT; Purpose
10/100 Fast Ethernet Switch User’s Guide About This Guide ix 0 A BOUT T HIS G UIDE Congratulations on your purchase of DES-1012 Fast Ethernet Switch. Thisdevice integrates 100Mbps Fast Ethernet and 10Mbps Ethernet networkcapabilities in a highly flexible desktop package. Purpose This manual discusse...
Page 11 - NTRODUCTION; Fast Ethernet Technology
10/100 Fast Ethernet Switch User’s Guide Introduction 1 4 1 I NTRODUCTION This section describes the features of the DES-1012, as well as giving somebackground information about Ethernet and Fast Ethernet switchingtechnology. Fast Ethernet Technology The growing importance of LANs and the increasing...
Page 12 - Switching Technology
10/100 Fast Ethernet Switch User’s Guide 2 Introduction Switching Technology Another approach to pushing beyond the limits of Ethernet technology is thedevelopment of switching technology. A switch bridge's Ethernet packets atthe MAC address level of the Ethernet protocol transmitting amongconnected...
Page 13 - Features
10/100 Fast Ethernet Switch User’s Guide Introduction 3 Features The Switch is designed for easy installation and high performance in anenvironment where traffic on the network and the number of users increasecontinuously. The Switch with its rack size is specifically designed for network workgroups...
Page 14 - Performance Features
10/100 Fast Ethernet Switch User’s Guide 4 Introduction uplink port, you will not be able to use port one (1x) because theseports are logically connected. Performance Features • 10/100Mbps Auto-Negotiation and Auto-Sensing on All Ports • Full/half duplex operation for each port • 1.3 Gbps Switching ...
Page 15 - NPACKING AND; Unpacking
10/100 Fast Ethernet Switch User’s Guide Unpacking and Setup 5 5 2 U NPACKING AND S ETUP This chapter provides unpacking and setup information for the Switches. Unpacking Open the shipping carton of the Switch and carefully unpack its contents.The carton should contain the following items: ♦ One DES...
Page 16 - Setup; Rack Installation
10/100 Fast Ethernet Switch User’s Guide 6 Unpacking and Setup Setup Consider the following when setting up the Switch: ♦ The power outlet should be within 1.82 meters of the device. ♦ Visually inspect the power cord and see that it is fully secured to theAC power connector. ♦ Make sure that there i...
Page 17 - Power On; LED Indicators
10/100 Fast Ethernet Switch User’s Guide Unpacking and Setup 7 Figure 1B, Installing the Switch in an equipment rack Power On The Switch can be used with AC power sources 100 to 240 VAC, 50 to 60Hz. The power switch is located at the rear of the unit adjacent to the ACpower connector and the system ...
Page 18 - Power Failure
10/100 Fast Ethernet Switch User’s Guide 8 Unpacking and Setup Power Failure As a precaution, the Switch should be turned OFF in case of a power failure.Press the power switch to the off or “0” position. When power is resumed,turn the Switch ON. At all times, avoid leaving the Switch ON after theocc...
Page 19 - DENTIFYING; Front Panel
10/100 Fast Ethernet Switch User’s Guide Identifying External Components 9 6 3 I DENTIFYING E XTERNAL C OMPONENTS This chapter describes the front panel, rear panel and LED indicators of theSwitch. Front Panel The front panel of the Switch consists of 12 (10/100 Mbps MDI-X) ports, oneUplink (MDI-II)...
Page 20 - Rear Panel
10/100 Fast Ethernet Switch User’s Guide 10 Identifying External Components Rear Panel The rear panel of the Switch consists of a power switch, an AC powerconnector, a system fan, a location for slide-in module, and a duplex-modeDip switch. Figure 3, Rear panel view of the Switch ♦ Slide-in Module S...
Page 23 - ONNECTING; PC to Switch
10/100 Fast Ethernet Switch User’s Guide Connecting the Switch 13 7 4 C ONNECTING T HE S WITCH This chapter describes how to connect the DES-1012 to your Fast Ethernetnetwork. PC to Switch A PC can be connected to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight cable. The PC (equipped wi...
Page 24 - Hub to Switch
10/100 Fast Ethernet Switch User’s Guide 14 Connecting the Switch connection, check the PC LAN card, the cable, switch conditions andconnections. The following are LED indicator possibilities for a PC to Switch connection: 1. The 100M LED indicator comes on for a 100 Mbps and stays off for 10 Mbps. ...
Page 26 - Using a Straight Cable
10/100 Fast Ethernet Switch User’s Guide 16 Connecting the Switch Using a Straight Cable When using straight cable, the connection can be made from the uplink(MDI-II) port of the Switch to any port of the Hub (see figure 7 ). Using a Crossover Cable When using crossover cable, the connection can be ...
Page 28 - Using a Crossover Cable; Console Management Program; Overview
10/100 Fast Ethernet Switch User’s Guide 18 Connecting the Switch Using a Crossover Cable When using crossover cable, this is done from any (MDI-X) port of theSwitch (Switch A) to any of the 10Mbps or 100Mbps (MDI-X) port of theother switch (switch B) or other devices (see figure 8). Switch A’s LED ...
Page 29 - Navigating the Console Program Screens
10/100 Fast Ethernet Switch User’s Guide Connecting the Switch 19 3. Set your terminal to the following setting: • Baud—9600 • Parity- None • Data Bits—8 • Stop Bit—1 4. Turn on the DES-1012. When you enter the main screen of the terminal,press the <Enter> or <Esc> key once to start comm...
Page 31 - Configuring the Console; System Submenu
10/100 Fast Ethernet Switch User’s Guide Connecting the Switch 21 useful: Figure 10, The Console Program Screen Map The following example illustrates how to disable or enable the AN function forPort 1: 1. Press P from the Main Menu to access the Port Submenu. 2. Press A in the port submenu to access...
Page 32 - Port Submenu
10/100 Fast Ethernet Switch User’s Guide 22 Connecting the Switch S: Display slide-in module status. This indicates the status of the slide-in module. If there is no module installed, the field will read, slide-inmodule is Absent.” If there is a module installed, this field will displaythe type of s...
Page 35 - Port Counter
10/100 Fast Ethernet Switch User’s Guide Connecting the Switch 25 port receiving buffer is full. Press 0 to disable flow control and press 1 to set data rate as 100Mbps. NOTE: Flow control is only available in half-duplex mode. In full-duplex mode, flow control is not available. The port status &...
Page 38 - ECHNICAL; General
10/100 Fast Ethernet Switch User’s Guide 28 RJ-45 Pin Specification $ 7 T ECHNICAL S PECIFICATIONS General Standards: IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100 Base-TX/FX Fast Ethernet ANSI/IEEE Std 802.3 NW ay auto-negotiation IEEE 802.3 Frame types: Transparent IEEE 802.3 MAC layer frame size: ...
Page 40 - Performance
10/100 Fast Ethernet Switch User’s Guide 30 RJ-45 Pin Specification Humidity: 5% ~ 95% non-condensing Dimensions: 442x258x44 mm (1U) W eight: 2.5 Kg EMI: FCC Class A, CE Mark Class A, VCCI Class A Safety: UL (UL 1950), CSA (CSA950), TUV/GS (EN60950) Performance Transmission Method: Store-and-forward...
Page 41 - IN
10/100 Fast Ethernet Switch User’s Guide RJ-45 Pin Specification 31 % 8 RJ-45 P IN S PECIFICATION When connecting your 10/100 Fast Ethernet Switch to another switch, abridge or a hub, a modified crossover cable is necessary. Please review theseproducts for matching cable pin assignment. The followin...
Page 43 - Offices
C O PTIONAL 100BASE-FX M ODULE The 100BASE-FX specification requires the fiberoptic cabling which is moreexpensive than the conventional UTP cabling. However, it has a definiteappeal to widespread LANs where cost of wiring is less important than thedistance it delivers to Ethernet LANs-400 meters fo...
Page 45 - Registration Card
Registration Card Print, type or use block letters. Your name: Mr./Ms _____________________________________________________________________________ Organization: ________________________________________________ Dept. ____________________________ Your title at organization: __________________________...
