Cub Cadet EW-7416APN - Manual

R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Di...

C A T A L O G Chapter I: Product Information ................................................................1   1-1 Product Introduction ........................................................................................ 1   1-2 Safety Information .................................................

1 Chapter I: Product Information 1-1 Product Introduction Thank you for purchasing this wireless access point! With this high cost-efficiency wireless access point, computers and wireless devices which are compatible with 802.11 Draft-N can connect to existing wired Ethernet network via this wireles...

3 1-3 System Requirements z Computer or network devices with wired or wireless network interface card. z Web browser ( Microsoft Internet Explorer 4.0 or above, Netscape Navigator 4.7 or above, Opera web browser, or Safari web browser). z An available AC power socket (100 – 240 V, 50/60Hz)

4 1-4 Package Contents Before you starting to use this access point, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items: □ Wireless Access point (main body, 1 pcs) □ 3dBi Dipole Antenna (2 pcs) □ QIG(1 pcs) □ A/C power adapter (1 p...

5 1-5 Familiar with your new wireless access point Front Panel LED Name Light Status Description PWR On The access point is switched on and correctly powered. On Wireless WPS mode is enabled. Off Wireless network is switched off. WLAN Flashing Wireless LAN activity (transferring or receiving data). ...

6 Back Panel z Antenna Connector Item Name Description Antenna 2 reserve SMA antenna connectors for screwing 3dBi detachable antennas enclosed with the product. Utilizing the MIMO technology, two antennas (Antenna A and C) are for signal transmitting and all three antennas are for signal receiving. ...

7 Chapter II: System and Network Setup 2-1 Installing the access point to your Network Please follow the following instruction to build the network connection between your new wireless access point and your computers, network devices: 1. Connect the access point to ADSL modem, router, or switch/hub ...

8 2-2 Connecting to wireless access point by web browser After the network connection is built, the next step you should do is setup the access point with proper network parameters, so it can work properly in your network environment. Before you can connect to the access point and start configuratio...

21 2-4 Select an Operating Mode for Wireless Access Point This access point can be operated in different modes; you can click ‘Basic Setting’ on the left of web management interface to select an operating mode you want to meet for different needs: You can click ‘Mode’ dropdown menu to select operati...

22 AP Bridge-WDS This mode is similar to ‘AP Bridge to Multi-Point’, but access point is not work in bridge-dedicated mode, and will be able to accept wireless clients while the access point is working as a wireless bridge. Universal Repeater This product can act as a wireless range extender that wi...

25 2-4-1-1 Multiple ESSID This access point supports four SSIDs. Except the main SSID (It can be configure in Basic Setting page), you can configure another three of SSIDs here. With different SSIDs, you can separate the wireless networks with different SSID name, wireless security, WMM, and VLAN se...

28 Auto MAC Clone If this function is enabled, the access point will automatically clone the MAC address of the wireless clients which is the first one to associate to the access point while the access point is powered on. After you finish with setting, please click ‘Apply’, and the following messag...

32 2-4-4 AP Bridge-Point to Multi-Point Mode In this mode, this wireless access point will connect to up to four wireless access points which uses the same mode, and all wired Ethernet clients of every wireless access points will be connected together. You can use this mode to connect a network to o...

43 default value is 100 DTIM Period Set the DTIM period of wireless radio. Do not modify default value if you don’t know what it is, default value is 3 Data Rate Set the wireless data transfer rate to a certain value. Since most of wireless devices will negotiate with each other and pick a proper da...

44 radio signal collisions between 802.11b and 802.11g wireless access points. It’s recommended to set this option to ‘Auto’. TX Power You can set the output power of wireless radio. Unless you’re using this wireless access point in a really big space, you may not have to set output power to 100%. T...

49 Default Tx Key You can set up to four sets of WEP key, and you can decide which key is being used by default here. If you don’t know which one you should use, select ‘Key 1’. Encryption Key 1 to 4 Input WEP key characters here, the number of characters must be the same as the number displayed at ...

64 Chapter III: Advanced Configuration 3-1 Configuration Backup and Restore You can backup all configurations of this access point to a file, so you can make several copied of access point configuration for security reason. To backup or restore access point configuration, please follow the following...

70 4-3 Glossary Default Gateway (Access point): Every non-access point IP device needs to configure a default gateway’s IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it...

71 1’s followed by consecutive trailing 0’s, such as 11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as “x” number of leading 1’s. When both are represented side by side in their binary forms, all bits in the IP address that correspond to 1’s in t...