Cub Cadet cs3310 - Manual

5 S ection 2 — i mportant S afe o peration p racticeS 3. Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. 4. Do not change the en...

6 S ection 2 — i mportant S afe o peration p racticeS Safety Symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S...

Assembly & Set-Up 3 7 Contents of Carton • One Chipper Shredder • One Operator’s Manual • One Engine Operator’s Manual • One Tow Bar • One Bag • One Safety Glasses • One Bottle of Oil Assembly NOTE: This unit is shipped without gasoline or oil in the engine. Fill up gasoline and oil as instructe...

8 S ection 3 — A SSembly & S et -U p Set-Up Gas and Oil Fill-Up Refer to the separate engine owner’s manual for additional engine information. 1. Add oil provided before starting unit for the first time out of the box. 2. Service the engine with gasoline as instructed in the separate engine owne...

Controls and Features 4 9 Chipper Chute Branches up to two inches (model series CS 2210) or three inches (model series CS 3310) in diameter may be fed into the chipper chute for chipping. Hopper Leaves, twigs, and branches up to 1/2-inch in diameter may be placed into the hopper for shredding. See F...

Operation 5 10 WARNING: The operation of any chipper shredder can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear the safety glasses provided with this unit or eye shields before chipping or shredding and while performing any adjustments or repa...

11 S ection 5 — o peration Emptying the Bag 1. Stop engine. 2. Squeeze the locking buckle to release the bag’s drawstrap before loosening it from the chute deflector. See Figure 5-2. Figure 5-2 3. Empty the bag and reattach to the chute deflector opening. Refer to the “Set-Up & Adjustments” sect...

Maintenance & Adjustments 6 12 Equipment Care • Clean the chipper shredder thoroughly after each use. • Wash bag periodically with water. Allow to dry thoroughly in shade. • If the reduction chamber becomes clogged, remove and clean as instructed below. NOTE: Cleaning with a forceful spray of wa...

13 S ection 6 — M aintenance & a djuStMentS 3. Remove the hairpin clip from the clevis pin which extends through the housing and shredder screen. See Figure 6-1 B. Remove clevis pin. 4. Pivot the shredder screen upward. See Figure 6-1 C. Clean the surrounding area by scraping away debris. 5. Con...

Service 7 14 7. Install a replacement blade (Part No. 742-0544) with the hardware removed earlier or sharpen. IMPORTANT: When sharpening the blade, protect hands by using gloves. Follow the original angle of grind and make sure to remove an equal amount from each blade. 8. To replace the other blade...

Troubleshooting 8 16 Problem Cause Remedy Engine Fails to start 1. Throttle lever not in correct starting position. 2. Spark plug wire disconnected. 3. Choke not in CHOKE position (if equipped). 4. Fuel tank empty or stale fuel. 5. Engine not primed (if equipped). 6. Faulty spark plug. 7. Blocked fu...

Replacement Parts 9 17 Component Part Number and Description 942-04050 Shredder Blade 942-0544B Chipper Blade 719-04308 Flail Blade (3 total) 634-04627 10 x 4.0 Pneumatic Wheel Phone (800) 965-4CUB to order replacement parts or a complete Parts Manual (have your full model number and serial number r...

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possessions and territories, and by MTD Products Limited with respect to new merchandise purchased and used in Canada and/or its territories and possessions.Thi...