Cub Cadet 600 series- User Manual

6 Chute Assembly (all models) 1. Apply a light lubricant (i.e. 3-in-1 oil) to the base of the chute assembly. 2. Place the chute assembly on the lip of the chute adapter. See Figure 3 3. One end of each chute keeper is already attached to the chute flange. Pivot the free end of the chute keeper to a...

7 Figure 8 Lamp Wire (optional) 1. Make sure the lamp wire is wrapped down the right handle as shown in Figure 9 . 2. Make sure the lamp wire is plugged into the alternator lead wire under the fuel tank. See Figure 9 inset. Figure 9 Chute Clean-out Tool 1. The chute clean-out tool is fastened with a...

8 SECTION 3: KNOWING YOUR SNOW THROWER Figure 10 WARNING: Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. NOTE: For detailed starting instructions and more information on all engine controls, refer to the separate engine manual packed wi...

9 Auger Control The auger control is located on the left handle. Squeeze the auger control against the handle to engage the augers and start snow throwing action. Release to stop. Drive Control The drive control is located on the right handle. Squeeze the drive control against the handle to engage t...

10 Electric Starter Outlet (If so equipped) Requires use of a three-prong outdoor extension cord (packed with the snow thrower) and a 120V power source/wall outlet. Augers When engaged, the augers rotate and draw snow into the housing. Chute Assembly Snow drawn into the auger housing is discharged o...

11 NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL. • Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing. NOTE: DO NOT use primer to restart a warm engine after a short shutdow...

12 Auger Control Test IMPORTANT: Perform the following test before operating your snow thrower for the first time and at the start of each winter season. Check the adjustment of the auger control as follows: • When the auger control is released and in the disengaged “up” position, the cable should h...

13 Chute Clean-Out Tool The chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice become lodged in the chute assembly during operation, proceed as follows to safely clean the chute assembly and chute opening: • Release both the Auger...

14 SECTION 5: MAKING ADJUSTMENTS WARNING: Never attempt to make any adjustments while the engine is running,except where specified in operator’s manual. Shift Rod Adjustment If the full range of speeds (forward and reverse) cannot be achieved, refer to the figures to the right and adjust the shift r...

16 SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER WARNING: Before lubricating, repairing, or inspecting, disengage all controls and stop engine. Wait until all moving parts have come to a complete stop. Engine Refer to the separate engine manual packed with your unit for all engine maintenan...

17 • To remove skid shoes, remove the four carriage bolts and hex flange nuts which secure them to the snow thrower. Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. Refer to Figures 19 and 21. • To remove shave plate, remove the carriage bolts, cupped w...

18 • Push idler away from the chute and insert a Philips head screwdriver in the hole on the idler as shown in Figure 26. This will release tension on drive belt. Figure 26 • Pull drive belt out and away from the engine pulley to remove. See Figure 26. • Tip the snow thrower up and forward, so that ...

20 SECTION 8: TROUBLE SHOOTING Problem Cause Remedy Engine fails to start. 1. Fuel tank empty, or stale fuel. 2. Blocked fuel line. 3. Choke not in ON position 4. Faulty spark plug. 5. Safety key not in ignition switch on engine. 6. Spark plug wire disconnected. 7. Primer button not being used prope...

21 SECTION 9 : THREE (3) YEAR LIMITED WARRANTY For three (3) years from the date of original purchase of our products, we will either repair or replace, at its option, free of charge, F.O.B. Factory or authorized service firm, any part found to be DEFECTIVE IN MATERIAL and WORKMANSHIP for the origin...