Cub Cadet 343 - Manual - manualsarea.com

Page 2 - NOTES

Page 3 - CONTENTS; WARNING; IMPORTANT; SAFE OPERATION PRACTICES; TO THE OWNER; CALLING FOR SERVICE

3 CONTENTS Section Page Safe Operation Practices .............................................................................................. 3 To The Owner ............................................................................................................... 3 l Front Hitch Components .....

Page 4 - SECTION I. FRONT HITCH COMPONENTS; Figure 1

4 SECTION I. FRONT HITCH COMPONENTS Before beginning installation of the Front HitchSystem, remove all parts from the shipping container.Refer to Figures 1 and 2 to confirm that all parts arepresent and to familiarize yourself with the partdescriptions. Throughout the installation instructions in th...

Page 5 - Figure 2; OPTIONAL MANUAL ANGLING KIT

5 Ref. No. Part No. Description Qty. A 710-0805 Hex Cap Screw, 5/16-18 x .1.5 ..... 1 B 710-0528 Hex Cap Screw, 5/16-18 x 1.25 1 C 710-3025 Hex Cap Screw, 5/16-18 x.625 GR5 2 D 712-0429 Hex Insert Lock Nut, 5/16-18 ........ 4 E 710-3131 Hex Cap Screw, 1/2-13 x 1.0 GR5 4 F 712-3083 Hex Insert Lock Nu...

Page 6 - REMOVE THE TRACTOR SEAT.; Figure 4; Figure 5; REMOVE THE FENDER AND RUNNING; NOTE; Figure 6

6 SECTION II. TRACTOR PREPARATION This section contains instructions for preparing thetractor for installation of the Front Hitch System. WARNING Place the tractor on a firm and level surface,disengage the PTO, and turn the ignition switchto the OFF position. Chock the front wheels toprevent the tra...

Page 8 - REMOVE THE LEFT REAR WHEEL.; MOVE THE FUEL TANK REARWARD.

8 WARNING Use care when handling the fender and runningboard assembly. The edges could cause cuts tothe skin. 9. With the help of an assistant, lift the front of therunning board off the frame brackets, then raisethe rear fender over the neck of the fuel tank andthe lift handle to remove the fender ...

Page 9 - SECTION III. INSTALLATION; INSTALL THE HYDRAULIC VALVE.; CAUTION; HYDRO

9 SECTION III. INSTALLATION This section contains instructions for installing theFront Hitch System on the tractor. If the optionalHydraulic Angling Kit (190-288-100) is also beinginstalled, refer to the installation instructions in itsOperator’s Manual as you complete each of thefollowing steps. So...

Page 13 - INSTALL THE HYDRAULIC TUBES AND

13 Figure 25 18. Mfg. Code 1D178G20023 and After. If not already installed, install a backup O-ring (P)between the existing O-ring and the flange of thehydro return hose. Insert the hydro return hose intothe rear port of the new valve and secure with thepreviously removed valve clamp and hex screw. ...

Page 19 - SECTION IV. TRACTOR REASSEMBLY; B. REINSTALL THE FENDER AND RUNNING

19 SECTION IV. TRACTOR REASSEMBLY A. REPOSITION FUEL TANK AND HITCH PLATE. 1. Slide the fuel tank fully forward in the frame slots. 2. If used, remove any plug or covering from thedipstick hole of the transmission housing. 3. While guiding the dipstick tube into thetransmission opening, pivot the hi...

Page 24 - MANUFACTURER’S LIMITED WARRANTY FOR:

MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. “Cub Cadet” warrants this product against defects in material and workmanship for a period of ...

Cub Cadet 343 - Manual

Table of Contents:

Summary

Other Cub Cadet Models