Cub Cadet 190-002 - User Manual

Check the blade(s) and engine mounting bolts at frequent intervals for proper tightness. Also, visually inspect blade(s) for damage (e.g., excessive wear, bent, cracked). Replace the blade(s) with the original equipment manufacturer’s (O.E.M.) blade(s) only, listed in this manual. “Use of parts whic...

Sight and hold this level with a vertical tree... or a corner of a building... or a fence post Fold along dotted line (represents a 15° slope) 15° Us e t his p ag e a s a guide to dete rm in e s lo pes whe re y ou may n ot o pe rat e s afe ly. W A R N IN G : D o not o p er ate you r l aw n mow er o ...

10 A. HOUR METER / BATTERY DISPLAY The hour meter records and digitally displays thehours that the tractor has been operated (tenths of anhour - right most digit). NOTE: The hour meter is activated whenever the igni- tion switch is turned to an ‘On’ position. Keep a recordof the actual hours of oper...

12 L. LIFT HANDLE The lift handle is located in the left fender and is usedto raise and lower equipment used with the tractor. Theequipment can be set in any of six positions by de-pressing the top button on the handle, moving the han-dle to the desired position, then releasing the button. Itmay be ...

13 Section 4: Operation WARNING: Before you operate the trac-tor, study this manual carefully.Familiarize yourself with the operationsof all the instruments and controls.Learn to operate this machine safely.Don’t risk INJURY or DEATH. 1. Before starting the engine, the operator must beseated, the PT...

14 STARTING THE ENGINE WARNING: For personal safety, theoperator must be sitting in the tractorseat when starting the engine. Never tryto start the engine while standing on theground. 1. Operator must be sitting in the tractor seat. 2. Pull choke control knob to full choke position.Less choking may ...

16 • Turn the ignition switch to “STOP’” and removethe key from the switch before dismounting. PTO CLUTCH BREAK-IN (Before initial use ONLY) Before operating the new clutch under load (mowinggrass, etc.), perform the following break-in procedure: 1. Start and run the engine a few minutes to warm up....

17 Figure 4-3 5. To remove the mulching plug, raise the chutedeflector and lift the mulching plug upward, thenoutward to disengage from the deck. Lower thechute deflector. USING “REVERSE CAUTION MODE” KEY POSITION NOTE: Mowing in reverse is not recommended. The “REVERSE CAUTION MODE” position of the...

19 Section 5: Maintenance and Adjustments MAINTENANCE CHECKING THE ENGINE Refer to the Kohler Owner’s Manual for all enginemaintenance intervals, procedures, specifications andinstructions. CHECKING TRANSMISSION OIL LEVEL NOTE: Check the oil level only while the engine is stopped and the tractor is ...

21 • Move the tractor to an area within reach of thehose where the dispersal of wet grass clippings isnot objectionable to you. Disengage the PTO,engage the parking brake, and stop the engine. • Pull back the lock collar of the nozzle adapter andpush the adapter onto one of the deck washnozzles at e...

22 NOTE : We do not recommend the use of a pressure washer or garden hose to clean your tractor. They maycause damage to electrical components; spindles;pulleys; bearings; or the engine. The use of water willresult in shortened life and reduce serviceability . 5. Lubricate all lubrication points sho...

24 3. Refer to Figure 5-9. Measure and record thedistance from the front cutting edge to the ground(measurement A), and from the rear cutting edgeto the ground (measurement B), for each of theblades. The front edge of each blade(measurement A) should be lower than its backedge (measurement B) by 1/8...

25 e. Note the index hole position used for the reargauge wheels. Insert a shoulder screw into afront ball wheel and slide a bell washer ontothe threads of the shoulder bolt. Note : The crown (rounded side) of the bell washer shouldbe against the shoulder of the bolt . Install the shoulder bolt and ...

27 LUBRICATION TABLE Point of Lubrication Check at Hours Change at Hours Capacity Anticipated Air Temperature Above + 32°F Below + 32°F Engine crankcase Checkbefore each use 100 Approx. 4 pints Cub Cadet Engine Oil SAE 10W30 Cub Cadet Engine Oil SAE 5W20 or 5W30 Hydro transmission and transaxle with...

29 Section 6: Service This section contains information for the variousadjustments and service procedures on the tractor.Refer to the Kohler engine manual for engine serviceinstructions and intervals, but use the instruction in thefollowing sub-section when the draining the enginecrankcase. DRAINING...

30 having a capacity of more than 6 quarts. Reinstallthe drain plug (See Figure 6-2). IMPORTANT: If the transmission oil is to be re-used, cover the container holding the drained oil to preventcontamination. Contaminated transmission oil candamage the hydro transmission. Figure 6-2 3. Clean around t...

31 WHEEL ALIGNMENT The front wheels should toe-in approximately 1/8 to1/4 inch, as measured across dimensions A and Bshown in Figure 6-4. Figure 6-4 FRONT WHEEL ADJUSTMENT WARNING: Place the tractor on a firm andlevel surface. To adjust the toe-in, proceed as follows: 1. Check the steering gear to e...

32 Figure 6-6 3. Grasping the ends of the pivot axle, attempt tomove each end of the axle forward and rearwardto check for side play between the axle and framechannel. If play is present, gradually tighten thelock nuts until play is minimized. 4. Repeat steps 2 and 3 until minimum play withoutbindin...

35 REMOVAL OF MOWER DECK WARNING: Before removing the mowerdeck, place the PTO switch in the “OFF”position, engage the parking brake, turnthe ignition key to the “OFF” positionand remove the key from the switch.Disconnect the spark plug wire foradditional safety. 1. Position the tractor and mower de...

36 6. Pull the deck support pins outward, turndownward and release so both spring-loadedpins are held in the disengaged position againstthe outer surface of the deck brackets (Refer toFigure 6-14). Figure 6-14 7. Raise the tractor implement lift handle to its high-est setting. Roll the mower deck fo...

37 When removing the blades, use a 1-1/8 inch wrench tohold the hex head of the spindle bolt when looseningthe hex nut securing the blade. A block of wood maybe placed between the deck housing and the cuttingedge of the blade to help in breaking loose the hex nutsecuring the blade (Refer to Figure 6...

41 Section 7: Trouble Shooting Possible Cause Possible Remedy HARD TO START No gasoline in fuel tank or carburetor ..................... Fill the tank with gasoline. Check the fuel line, carburetor and fuel filter. Fuel line or carburetor clogged ............................... Clean the fuel line a...

42 Trouble Shooting Possible Cause Possible Remedy LACK OF POWER Air cleaner clogged ................................................. Service the air cleaner element. Refer to “MAINTE- NANCE.” Engine overload ...................................................... Reduce the load. Engine overheated ...

43 MODEL GT 2544 SERIES 2500 22 HP KOHLER Engine Oil Requirements approx. . . 4 pints Part No. Cub Cadet engine oil (Grade SG,SH,SJ or higher)Ambient temperature viscosity Above +32°F SAE 10W30 Below +32°F SAE 5W20 or 5W30 737-3030A (10W30) 737-3049 (5W30) Air Filter Requirements Part No. Clean air ...

44 Section 9: Optional Equipment And Accessories When you purchased your tractor, you probably had it completely equipped for your particular needs at the time.However, later you may wish to obtain optional equipment or accessories. Refer to the chart below for a list ofoptional equipment and access...

45 GT 2544 2.0 gallons 4 pints 6 qts. 0 to 6 mph0 to 3 mph Kohler Command 22 HP 2 3.03 in.2.64 in. 38.1 1200 RPM 3600 RPM ± 75 Battery .030 in. 12 volt neg. ground 725-1707D 15 amp regulated 25 amp 725-0963 Internal expanding 16 x 6.5-8 23 x 9.5-12 31.5 in. 30.25 in.47.00 in.72.00 in.49.00 in.42.00 ...

IMPORTANT: To obtain warranty coverage owner must present an original proof of purchase and applicable maintenance records to the servicing dealer. Please see the operator’s manual for information on required maintenance and service intervals.The limited warranty set forth below is given by Cub Cade...