Crown BWC070 - Manual
Crown BWC070 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – VII Venting; WARNING
- Page 5 – FIGURE 7.2: HORIZONTAL CONCENTRIC VENTING
- Page 7 – ) Permitted Terminals for Vertical Venting; • Vent Option 5; require the use of wall thimbles.; TABLE 7.5: PERMISSIBLE STAINLESS STEEL VENT SYSTEMS
- Page 8 – FIGURE 7.6c: POSITIONING VENT TERMINAL UNDER OVERHANGS
- Page 10 – TABLE 7.9: SUMMARY OF VERTICAL VENTING OPTIONS
- Page 13 – C. Assembly of Crown 60/100mm Concentric Venting; resulting in unsafe or unreliable operation.; terminal and the inner pipe.; outer pipe only
- Page 15 – Use a drill stop or other means to ensure that; it out from the female end.
- Page 17 – D. Assembly of Crown 80/125mm Concentric Venting; Description
- Page 18 – OUTER PIPE ONLY; d) Make an insertion mark 1” from the male end of the outer pipe.
- Page 19 – Use a drill stop or other means to ensure that the drill bit does not
- Page 20 – hole through both outer pipes to start these screws.; Use a drill stop or other means to ensure that the; plate to the inside wall.
- Page 21 – FIGURE 7.33c: CUTTING INNER PIPE OF 80/125mm HORIZONTAL TERMINAL
- Page 22 – IMPORTANT
- Page 23 – following the instructions on Page 26.; Use a drill stop; and the Air Intake Section to prevent rain infi ltration.; dust and other debris from falling into the boiler.; with a fi le or emery cloth.; Use a drill stop or other means to ensure
- Page 24 – FIGURE 7.35c: COMPLETING VERTICAL TERMINAL INSTALLATION
- Page 25 – or other appliances.
- Page 26 – CAUTION; vent systems are used, take the following precautions:; E. Assembly of Stainless Steel Venting; piping sections are connected with PVC cement.
BWC070, BWC090, BWC120
Installation Manual Supplement
June 12
th
, 2007
The following pages are copied from the latest edition of the installation manual for
the above boilers, which is not yet in print. These pages cover new vent options that have
been added for these boilers and which are not shown in the current manual. These
options include:
1)
80/125mm concentric venting may be used to achieve longer vent runs.
2)
80/125mm concentric venting may be used for vertical vent applications.
3)
An 80/125mm concentric snorkel kit is now offered.
4)
Metal-Fab “Corr/Guard” may now be used for stainless steel vent applications.
Refer to the installation manual supplied with the boiler for important warnings and
other information not covered in this supplement.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
VII Venting WARNING FAILURE TO VENT THIS BOILER IN ACCORDANCE WITH THESE INSTRUCTIONS COULD CAUSE FLUE GAS TO ENTER THE BUILDING RESULTING IN SEVERE PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH: * Do not attempt to vent this boiler with galvanized, PVC, or any other vent components not listed in Table...
14 FIGURE 7.2: HORIZONTAL CONCENTRIC VENTING (VENT OPTION 1,3) FIGURE 7.3: HORIZONTAL TWIN PIPE VENTING (VENT OPTION 2)
6) Permitted Terminals for Vertical Venting - • Vent Option 5 - A straight termination is installed in the end of the vent pipe. Vent manufacturer part numbers for these screens are shown in Table 7.5. The air inlet terminal consists of a 180 degree elbow (or two 90 degree elbows) with a rodent scre...
