Crestron TPS-IMPC - Manual - manualsarea.com

Page 2 - 5 Volvo Drive

This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2003 Crestron Electronics, Inc.

Page 3 - Contents

Crestron TPS-IMPC Interface Module Contents Interface Module: TPS-IMPC 1 Introduction ...................................................................................... 1 Features & Functions ............................................................. 1 Specifications.........................

Page 5 - Introduction; Features & Functions; Specifications of the TPS-IMPC; SPECIFICATION; Optional Power Pack

Crestron TPS-IMPC Interface Module Interface Module: TPS-IMPC Introduction Features & Functions The TPS-IMPC is an interface module designed for, and included with the Crestron  TPS-3000, TPS-5000, and TPS-6000 tilt touchpanels. The sleek design of the touchpanel base left little room for all t...

Page 6 - Physical Description; Physical Views of the TPS-IMPC; Ports

Interface Module Crestron TPS-IMPC Physical Description The TPS-IMPC, shown in the following diagram, is supplied with the TPS-3000, TPS-5000, and TPS-6000 tilt touchpanels. The module is housed in a black enclosure with a silk-screened top panel. An AC adapter port, network connector, and video inp...

Page 7 - BNC connectors are physically located next to the twisted pair

Crestron TPS-IMPC Interface Module NTSC/PAL VIDEO The NTSC/PAL video input consists of three connectors; two BNC connectors for unbalanced video signals and one 6-pin mini-connector for twisted pair wiring of balanced video signals. The video signal is connected to these ports and requires a TPS-300...

Page 8 - must; TYPE PIN DESIGNATION

Interface Module Crestron TPS-IMPC CAUTION: If power is provided to the TPS-IMPC from the +24VDC on a Cresnet connector or the PW-2420RU, power must not be applied to the power input on the touchpanel base. NOTE: When power is supplied through this connector, Crestron recommends disconnecting the +2...

Page 9 - AUDIO Pinouts; AUDIO INPUT

Crestron TPS-IMPC Interface Module CAUTION: The 10-pin RJ-45 net/video connector cable supplied by Crestron is a custom cable and is the only one that should be used. The end of the cable has a metal shield that is required to protect the equipment. Using non-Crestron cables will result in damage to...

Page 10 - AUDIO INPUT Pinouts; MIC OUT; PIN DESCRIPTION

Interface Module Crestron TPS-IMPC AUDIO INPUT Pinouts PIN DESCRIPTION S Shield R + Right Positive R - Right Negative L + Left Positive L- Left Negative S Shield MIC OUT The port mates with a three-pin connector (supplied) and produces line level differential output. Description of the pinouts is sh...

Page 11 - Industry Compliance; Setup; Network Wiring; Use only Crestron power supplies for Crestron equipment.

Crestron TPS-IMPC Interface Module Industry Compliance As of the date of manufacture, the TPS-IMPC has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling (N11785). Setup Network Wiring CAUTION: Use only Crestron power...

Page 12 - Resistance Equation; WIRE GAUGE; When daisy-chaining Cresnet units, strip the ends of the wires; Hardware Hookup

Interface Module Crestron TPS-IMPC must be taken into consideration. If network units are to be daisy-chained on the run, the power factor of each network unit to be daisy-chained must be added together to determine the power factor of the entire chain. The length of the run in feet and the power fa...

Page 13 - When connecting the net/video cable from the interface module; DO NOT; Hardware Hookup for the TPS-IMPC

Crestron TPS-IMPC Interface Module TPS-5000 or TPS-6000 touchpanel and a video window object resides on a page within the uploaded Crestron VisionTools ® Pro-e (VT Pro-e) project. NOTE: When connecting the net/video cable from the interface module to the touchpanel, exceeding a cable length of 30 fe...

Page 14 - Problem Solving; Troubleshooting; TPS-IMPC Troubleshooting; TROUBLE

Interface Module Crestron TPS-IMPC Problem Solving Troubleshooting The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative. TPS-IMPC Troubleshooting TROUBLE POSSIBLE CAUSE(S) CORRECTI...

Page 15 - Switch to “composite” video.; Further Inquiries

Crestron TPS-IMPC Interface Module TPS-IMPC Troubleshooting (continued) TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION Incorrect video format selection. Select the proper video input configuration in the touchpanel configuration SETUP MENU. Incorrect VT Pro-e project file loaded. Make sure that video w...

Page 16 - Future Updates; ) periodically for manual

Interface Module Crestron TPS-IMPC Future Updates As Crestron improves functions, adds new features, and extends the capabilities of the TPS-IMPC, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the re...

Page 17 - Return and Warranty Policies; Merchandise Returns / Repair Service

Crestron TPS-IMPC Interface Module Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange, or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact the factory and request an RMA ...

Page 18 - This page intentionally left blank.

Interface Module Crestron TPS-IMPC 14 • Interface Module: TPS-IMPC Operations Guide - DOC. 6162 This page intentionally left blank.