Crestron CLS-EXP-DIMFLV - Manual
Crestron CLS-EXP-DIMFLV – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Industry Compliance; Reorient or relocate the receiving antenna.
- Page 3 – Application
- Page 4 – Physical Description
- Page 5 – Setup; Important Notes; Read before installation.; Installation; Hardware Hookup; NEUT
- Page 6 – Replace the cover and cover screws.; Problem Solving; Troubleshooting
- Page 7 – Return and Warranty Policies; Further Inquiries; Merchandise Returns / Repair Service
- Page 8 – This page is intentionally left blank.
CLS-EXP-DIMFLV
Crestron Electronics, Inc.
Installation Guide – DOC. 6680A
15 Volvo Drive Rockleigh, NJ 07647
(2020652)
Functional Summary
The CLS-EXP-DIMFLV enables the expansion of the
Crestron
®
iLux™ Integrated Lighting System and other
Crestron lighting dimmers to support 120 - 277 Volt loads
up to 16 Amps. It allows any output channel of a
compatible dimmer or switch to control a fully loaded
circuit of 0-10 VDC fluorescent ballasts
1
, non-dimmed
lighting (incandescent, HID, magnetic low voltage
(MLV), electronic low voltage (ELV), neon/cold cathode,
and fluorescent ballast) up to 16 amps, and motors rated
up to 1/2 HP @ 120 Volts, 1 HP @ 230/277 Volts.
The CLS-EXP-DIMFLV is designed for mounting to a
vertical surface. Conduit knockouts are provided on the
bottom and lower sides. All connections are made via
screw terminals behind the front cover.
•
Works with Crestron iLux (CLS(I)-C6),
CLW-Series dimmers
2,3
, CLX-Series dimmers
3
,
and DIN-1DIMU4
3
•
Emulates the characteristics of the dimmer that is
controlling it
•
Up to five Expansion Modules can be connected
to a single iLux dimmer channel
•
Supports 0-10 VDC fluorescent, non-dimmed
lighting (including HID), and motors rated up to 1
HP
•
Built-in air gap relay at the output
1.
Ballasts must comply with the specifications for control by DC
voltage in ANSI C82.11:2002 and IEC60929:2006.
2.
CLW-Series devices must have a dedicated neutral.
3.
The CLS-EXP-DIMFLV can only be controlled by forward-phase
dimmer modules. It is not compatible with the CLX(I)-1DELV4. If
connected to a DIN-1DIMU4, the DIN-1DIMU4 must be set to
operate as a forward-phase dimmer or a non-dimming switch.
CLS-EXP-DIMFLV Physical View
Specifications
CLS-EXP-DIMFLV Specifications
SPECIFICATION DETAILS
Load Ratings
Output
Channels
Load
Ratings:
Lamp
Motor
Minimum
Load
at 120 Volts
at 230 Volts
at 277 Volts
Load
Types
1
16 Amps @ 120 – 277 Volts
(70 mA max current sink for 0-10
VDC ballasts)
1/2 HP @ 120 Volts,
1 HP @ 230/277 Volts
15 Watts
25 Watts
30 Watts
Dimmable Loads
0-10 VDC dimmable fluorescent
ballasts (i.e. Advance Mark 7 or
other ballasts that are compliant
with the specifications for control
by DC voltage in ANSI
C82.11:2002 and IEC60929:2006)
Non-Dim Loads
Incandescent, HID, magnetic low
voltage (MLV), electronic low
voltage (ELV), neon/cold cathode,
and fluorescent ballasts
Motors
Up to 1 HP @ 230/277 Volts
Input Voltages
Line
Power
Control
Input
120 to 277 Volts AC, 50/60 Hz
120 or 230 Volts AC, 50/60 Hz,
phase independent of line power
and load, presents 25 Watts load
to the controlling device
Electrical Terminals
Captive screw type;
Accommodates two 22-12 AWG
(0.34-4.0 mm
2
) wires
Enclosure
Surface mount module with (2)
integral mounting flanges,
galvanized steel w/gray matte
powder coat front panel, extruded
aluminum heat sink, 1/2” and 3/4”
conduit knockouts provided on
bottom and lower left & right sides
Environmental
Temperature
Humidity
Maximum
Heat
Dissipation
32° to 104°F (0° to 40°C)
10% to 90% RH (non-condensing)
68 BTU/Hr
Dimensions
Height
Width
Depth
Weight
8.82 in (22.40 cm)
6.39 in (16.23 cm)
3.18 in (8.08 cm)
3.3 lbs (1.5 kg)
(Continued on following page)
Tel: 888.CRESTRON
07.08
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
iLux™ Expansion Module Crestron CLS-EXP-DIMFLV CLS-EXP-DIMFLV Specifications (Continued) SPECIFICATION DETAILS Compatible Control Devices CLS(I)-C6 Series CLW Series CLX(I)-1DIM4 CLX-1DIM8 CLX(I)-2DIM2 CLX(I)-2DIM8 DIN-1DIMU4 iLux Integrated Lighting System Wall Dimmers and Switches Four Channel Dim...
Crestron CLS-EXP-DIMFLV iLux™ Expansion Module Application The following diagram shows several CLS-EXP-DIMFLV modules in a typical application. CLS-EXP-DIMFLV modules in a lighting application Installation Guide – DOC. 6680A iLux™ Expansion Module: CLS-EXP-DIMFLV • 3
iLux™ Expansion Module Crestron CLS-EXP-DIMFLV Physical Description This section provides information on the connections and indicators available on the CLS-EXP-DIMFLV. CLS-EXP-DIMFLV Overall Dimensions 8.82 in (22.40 cm) 5.79 in (14.71 cm) 4.99 in (12.67 cm) 3.07 in (7.80 cm) 3.18 in (8.08 cm) Ø 0....
