Crate VTX200SH - Manual - manualsarea.com

Page 2 - Three-Channel Guitar Amp Head with Stereo DSP; Declaration of Conformity; Manufacturer’s Name: SLM Electronics

TABLE OF CONTENTS: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4,5 The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - Congratulations; the information contained in this guide before you begin playing.; And thank you for choosing; CR; IMPORTANT SAFETY INSTRUCTIONS; CAUTION

3 Congratulations ! You are now the proud owner of the Crate VTX200SH three-channel guitar amp head with Stereo Digital Signal Processing (DSP). This rugged amplifier combines out-standing features with serious clean and distorted sounds. Dual DSP controls provide15 “Must Have” effects and 15 Delay ...

Page 4 - 1: LEVEL: Use this control to adjust the output level of Channel 3.

4 The Front Panel: MUTE MUTE MUTE DELAY DELAY REVERB REVERB EFFECTS EFFECTS WA H W A H PHASE PH A SE WA H W A H OCT OCT - E CH O SI N G L E F LA NG E CH O R U S S P E C IA L PIN G P O N G PH A S E R 1 3 3 1 4 2 2 2 2 3 1 1 3 4 4 1 3 1 4 2 2 2 3 1 3 4 4 TAP / SAVE GAIN LEVEL 3 HIGH POWER MID LOW 1 2 ...

Page 6 - SPEAKER; in a shock injury or damage to the unit.

6 28 29 30 31 32 33 34 The Rear Panel: 28: FOOTSWITCH: Use this jack to connect the footswitch cable (5-conductor midi cable) to the four-buttonfootswitch (supplied). This allows you to remotely switch between the channels, set tap tempos, save new presets,and access a second set of DSP presets. (Se...

Page 7 - NAME

7 The DSP Section: The VTX200SH features DSP controlsfor Reverb, Delay and Effects. Completeinformation about the Effects and Delaycontrols is given below. The Delay con-trol selects the delay or echo effects.The Effects control selects the “pitch modified” and wah effects. Many of these effectshave...

Page 8 - HOLD 3 SECONDS; CHANGES ARE

8 Storing Your Own Presets: Each channel of the VTX200SH has two factory assigned DSP presets, as shown on pages 10 and 11. No matter what the settings of the DSP controls, the preset is recalledwhen a channel is selected. You may change the DSP settings by rotating the DSP con-trols - these changes...

Page 9 - Using the Footswitch:; When the footswitch is connected; sets are only accessible; FOOTSWITCH

9 VTX200SH Three-Channel Guitar Amp Head with Stereo DSP Using the Footswitch: The special Crate four-button footswitch supplied with the VTX200SH performs a variety of functions. The footswitch allows remote channel selection, remote Tap/Savefor each channel, and allows access to an additional DSP ...

Page 10 - TAP Tempo MEDIUM; Factory Preset 2: Rhythm w/Slapback Delay; TAP Tempo FAST; The VTX200SH Factory Presets for the DSP section are as follows:

10 DSP Factory Presets: DELAY DELAY REVERB REVERB EFFECTS EFFECTS WA H W A H PHAS E PH A SE WA H W A H OCT OCT - E CH O SI N G L E F LA NG E CH O R U S S P E C IA L PIN G P O N G PH A S E R 1 3 3 1 4 2 2 2 2 3 1 1 3 4 4 1 3 1 4 2 2 2 3 1 3 4 4 TAP / SAVE DELAY DELAY REVERB REVERB EFFECTS EFFECTS WA ...

Page 14 - Copy this page to fill in your own DSP Presets!

14 DSP “Fill in the Blanks” (for User Presets): DELAY DELAY REVERB REVERB EFFECTS EFFECTS WA H W A H PHAS E PH A SE WA H W A H OCT OCT - E CH O SI N G L E F LA NG E CH O R U S S P E C IA L PIN G P O N G PH A S E R 1 3 3 1 4 2 2 2 2 3 1 1 3 4 4 1 3 1 4 2 2 2 3 1 3 4 4 TAP / SAVE DELAY DELAY REVERB RE...

Page 15 - System Block Diagram:; CHANNEL 1

15 System Block Diagram: MUTE REVERB EFFECTS DELAY INPUT CHANNEL 1 INPUT BUFFER GAIN MID HIGH LOW LEVEL FLEX WAVE (LOW GAIN) CHANNEL 2 GAIN MID HIGH LOW LEVEL FLEX WAVE (MEDIUM GAIN) CHANNEL 3 GAIN MID HIGH LOW LEVEL FLEX WAVE (HIGH GAIN) SWITCH CONTROLLER DSP TAP/ SAVE DSP A/B FOOTSWITCH 1 2 3 4 TU...

Page 16 - VTX200SH TECHNICAL SPECIFICATIONS:

VTX200SH TECHNICAL SPECIFICATIONS: Output Power Rating 70W per channel @5% THD, 8 ohm load 100W per channel @5% THD, 4 ohm load Input Impedance 470k Ω Total System Gain Ch 1 74dB, all controls @10 Ch 2 88dB, all controls @10 Ch 3 103dB, all controls @10 Maximum Input Signal Accepted 5 volts peak-to-...

Crate VTX200SH - Manual

Table of Contents:

Summary

Other Crate Models