Craftsman CMXEBAR600 - User Manual

English 6 Your risk from these exposures varies depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particle...

7 English Minimum gauge for Extension Cords (AWg) Volts Total length of Cord in Feet (meters) 120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7) 240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4) Ampere Rating American Wire gauge More Than not More Than 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 1...

English 8 TOOLS NEEDED FOR ASSEMBLY CARTON CONTENTS Unpacking And Checking Contents Carefully unpack the band saw and all its parts, and compare against the list below and the illustration. With the help of an assistant, place the saw on a secure surface and examine it carefully. WARNING: To avoid i...

9 English Installing And Removing Blade (Fig. G, H) WARNING: To avoid injury from accidental starting, always turn the switch OFF and remove the plug from the power source before moving, replacing, or adjusting the blade. Removing (Fig. G, H) 1. Loosen the blade tension by turning the blade tension ...

11 English Adjustment Instructions WARNING: To avoid injury, turn the switch OFF and unplug the band saw from the power source before making any adjustments. Table Adjustments (Fig. J) Tilting the table The band saw table can be tilted from 0° to 45° right.1. Loosen the table lock handle 19 on the r...

English 12 4. Using a feeler gauge, make sure the space between guide pins and the blade measured is 0.002 in. (0.05 mm the thickness of a dollar bill). 5. Tighten the front hex socket screws 42 . 6. Loosen the side hex screw 44 by turning counterclockwise with a 4 mm hex wrench supplied. (Fig. N) 7...

13 English Support bearing (Fig. Q) 1. Loosen the support bearing hex screw 44 on the right side of the band saw with the hex wrench. 2. Move the support bearing shaft 48 in or out until the support bearing 49 is 1/64 in. (0.4 mm) behind the saw blade. 3. Tighten the support bearing hex screw 44 . 4...

English 14 OPERATIONBasic Saw Operations"ON/OFF" Switch (Fig. S) The switch with safety key is intended to prevent unauthorized us of the band saw.1. To turn the band saw ON, insert the black safety key 51 into the key slot in the center of the switch 14 . 2. Push the key firmly into the slo...

15 English Blade Selection (Fig. U) CAUTION: Blade teeth are sharp. Use care when handling a saw blade. CAUTION: For longest wear and best cutting results, use the correct blade thickness, width, and temper for the type of material you will cut. When sawing small curves and delicate work, use narrow...

English 16 Motor Frequently blow or vacuum out any sawdust from the motor. Follow lubrication instruction on the motor label. WARNING: To avoid electrocution or fire, immediately replace a worn, cut or damaged power cord. Adjusting The Upper Blade Guide Travel (Fig. V) If the upper blade guide assem...

17 English TROUBLESHOOTING GUIDE BE sURE TO FOllOW sAFETY RUlEs AnD insTRUCTiOns For assistance with your product, visit our website at www.craftsman.com for a list of service centers, or call CRAFTSMAN at 1-888-331-4569. PlEAsE READ ThE FOllOWing: The manufacturer and/or distributor is providing th...

19 English Register Online Thank you for your purchase. Register your product now for: • WARRAnTY sERViCE: Registering your product will help you obtain more efficient warranty service in case there is a problem with your product. • COnFiRMATiOn OF OWnERshiP: In case of an insurance loss, such as fi...

English 20 i.D.no. Description size Q’ty i.D.no. Description size Q’ty X7BF MOTOR ASS’Y 1 X7CW SHAFT 1 X7BH LOWER BEARING GUIDE ASS’Y 1 X7CX HEX NUT 5 X7BJ LOWER BLADE GUIDE SUPPORT 1 X7CY HEX BOLT M6*20 4 X7BL LOWER BLADE WHEEL ASS’Y 1 X7CZ DUST PORT 1 X7BM UPPER BLADE WHEEL ASS’Y 1 X7D1 ADJUSTING ...