Craftmade UCI-2000 - User Manual

GENERAL INFORMATION

This remote control is designed to separately control your ceiling fan speed and light brightness.

There are four buttons to control the fan speed. The light dimmer button controls the light brightness.

The red indicator on the transmitter will light when any button is pressed.

INSTALLATION AND OPERATING INSTRUCTIONS

I. SAFETY PRECAUTIONS

A.

DANGER: HIGH VOLTAGE!

Household electrical power can cause serious injury or death. Disconnect source of electrical

power to the ceiling fan by removing fuse or switching off circuit breaker. Make sure all electrical connections comply with local codes,
ordinances, the National Electrical Code, and ANSI/NFPA 70-1999. If you are unfamiliar with electrical wiring, please use a qualified
and licensed electrician.

B.

WARNING:

To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with the remote control

receiver are designed to accept only one 12-gauge house wire and no more than two lead wires from the receiver. If your
house wire is larger than 12-gauge or there is more than one house wire to connect to the two receiver wires, consult an
electrician for the proper size wire connectors to use.

C.

CAUTION:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THE FAN

WITH ANY SOLID STATE SPEED CONTROL DEVICE OR CONTROL FAN SPEED WITH A FULL
RANGE DIMMER SWITCH.

D.

Do

not

use this remote control with solid state ceiling fans, electrical source and fan must be

120 volts, 60 Hz. Maximum fan motor amps: 1.5; Maximum light watts: 300 incandescent

Electronic ballast (LED lights or CFL lights) 300VA

II. INSTALLATION OF RECEIVER (Please refer to Figure 1 before continuing.)

A.

Manually set fan speed control to HIGH via pull chain and set light to ON via pull chain.

IMPORTANT:

Fan speed and light control will not be activated by remote if pull chains for fan and light

are not set to the HIGH and ON positions, respectively.

B.

Disconnect source of electrical power to the ceiling fan by removing fuse or switching off circuit breaker.

C.

Lower ceiling fan canopy from the hanging bracket.

D.

Disconnect existing wiring between ceiling fan and supply at electrical outlet box.

E.

Lay the black antenna wire on top of the receiver and slide the receiver (flat side up) into the hanging bracket. (Figure 2)

F.

Using the wire connectors supplied, make wiring connections as follows: (Figure 3)

CONNECT:

TO:

GREEN

fan wire......................................................

BARE

supply wire

BLACK

receiver wire (AC IN L)...............................

BLACK

supply wire

WHITE

receiver wire (AC IN N)...............................

WHITE

supply wire

WHITE

receiver wire (TO MOTOR N)......................

WHITE

fan wire

BLACK

receiver wire (TO MOTOR L)......................

BLACK

fan wire

BLUE

receiver wire (FOR LIGHT)............................

BLUE

light wire (from fan)

Wrap each wire connector separately with electrical tape as an extra safety

measure.

If other fan or supply wires are different colors than those

mentioned, have this unit installed by a qualified electrician.

G.

Push all connected wires up into outlet box. Make sure antenna rests

outside

of

hanging

bracket.

H.

Re-install the canopy on the hanging bracket.

III. AUTOMATED LEARNING PROCESS

CAUTION:

The transmitter can be programmed to multiple receivers or fans. If this

is

not

desired, turn wall switch off to any other programmable receiver or fan.

A.

Remove faceplate from transmitter to reveal battery compartment and dimmer switch.

B

. Setting the dimmer switch:

Locate the dimmer switch above the battery compartment labeled “

DIM

” and “

ON

”. Set dimmer switch to ON (DIM)

position only if using incandescent bulbs. Set dimmer switch to OFF (ON) position if using LED or compact fluorescent
bulbs.

NOTE

: Most LED or compact fluorescent bulbs are

not

compatible for use with dimmer controls.

C.

Install 12-volt battery (included).

D.

Restore electrical power. Within 30 seconds of restoring electrical power, press the “OFF” button, located on the front of the remote control transmitter,
for 5 seconds or until light on fan blinks twice. Test the light and fan functions to confirm the programming (learning process) is complete. (Figure 4)

E.

Replace faceplate on transmitter.

(Figure 4)

IV. TRANSMITTER--CARE

AND

OPERATION

A.

If you find that your fan and light kit go on and off without using your remote control, turn power off and repeat Steps D and E in Section III (Automated
Learning Process).

B.

Store the transmitter away from excess heat or humidity.

C.

To prevent damage to transmitter, remove the battery if not used for long periods.

D.

Operation buttons on the front panel of the transmitter:

HIGH button

for fan HIGH speed

MED button

for fan MEDIUM speed

LOW button

for fan LOW speed

OFF button

for fan speed OFF

L1 button for light BRIGHTNESS and OFF
The light function is controlled by pressing the L1 button. Hold button down to increase or
decrease light. Tap button quickly to turn light off or on. If you press the button in excess of
0.7 seconds it becomes a dimmer. The light varies cyclically in 0.8 seconds. The light button
has auto resume so the light will stay at the same brightness as the last time it was turned off.

V. TROUBLESHOOTING GUIDE

A.

Remote control fails to operate:

1.

Make sure there is power to the receiver.

2.

Make sure the receiver is wired correctly.

3.

Make sure that the fan is set on the highest speed via pull chain.

4.

Make sure the light kit is turned on via pull chain.

5.

Make sure the battery in the remote control is good.

6.

The learning process between fan and remote control may not have been
successful. Turn power off and repeat Step D in Section III (Automated
Learning Process).

B.

Transmitter won't operate at distance:

If transmitter operates fan and light kit when up close but not at 40 feet away,
try placing the black antenna wire higher and make sure the black antenna
wire is visible.

Fig. 1

19˚

20˚

and

Above

RECEIVER

HANGING
BRACKET

DOWNROD

CAUTION:

FOR MOUNTING RECEIVER,CEILING

ANGLE SHALL NOT EXCEED 19 DEGREES
RECEIVER MODEL: CFR-3D

LITEX INDUSTRIES, LTD.

GRAND PRAIRIE, TX 75050

FOR CUSTOMER SERVICE CALL: 1-800-486-4892

Fig. 3

AC SUPPLY

BLACK

WHITE

BARE

GREEN

BLACK

WHITE

BLUE

BLUE

BLACK

WHITE

ANTENNA

Fig. 2

RECEIVER

CAUTION:

DO NOT USE

FAN SPEED CONTROL
IN CANOPIES WHERE
THE MOUNTING IS NOT
AS SHOWN IN FIGURE 2

MODEL: UCI-2000

AC SUPPLY

BLACK

WHITE

Fig. 4

TRANSMITTER

1

1

-

BATTERY

1

1

-

DIM ON

FACEPLATE

DIMMER

SWITCH

DIM ON

CAUTION:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

USE THE FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE

OR CONTROL FAN SPEED WITH A FULL RANGE DIMMER SWITCH.