Cortelco network adaptor - Manual

Page 3 - System Requirements; TELEPHONE LEVEL SWITCH -

Pre-Installation System Requirements - Windows 98 or later. Compliant with USB 1.1 requirements for bus powered devices. USBHub supports low power or self powered USB devices (each USB portprovides 100 mA). Pre-installation Guidelines - Before installing your DPA, observe the following guidelines: C...

Page 4 - Data Port Anywhere Installation; Connect the USB cable on the DPA to your computer USB; telephone handset; (2A) and insert it into the DPA jack labeled; PHONE; Connect your PC Card or internal modem cable to the DPA

Data Port Anywhere Installation Step 1. Connect the USB cable on the DPA to your computer USB port. The first time you connect the DPA to your computer, you will beprompted to install USB drivers, simply follow the prompts. The DPAuses standard Microsoft drivers. Follow the prompts to identify theDP...

Page 5 - not in use; , connect the included

Optional Connection: If you want to use the telephone for voice communications while the modem is not in use , connect the included coiled handset cord to the telephone handset and the DPA jack labeled HANDSET. If you have connected the telephone handset to the DPA lift thetelephone handset and list...

Page 6 - Windows Connection Setup; Because most digital PBX systems, such as; SETTINGS; Select CONTROL PANEL

Windows Connection Setup If you use the DPA while traveling we recommend that you modify yourmodem settings to setup your modem for manual dialing. Why Manual Dial? Because most digital PBX systems, such as Nortel Meridian, Rolm and others do not accept the analog dialingtones generated by the modem...

Page 7 - PROPERTIES; elect; CONNECTION; TAB

Step 5. In the General tab, highlight the modem to be used, then S elect PROPERTIES (not Dialing Properties) Step 6. S elect CONNECTION TAB Step 7. Under Call preferences uncheck the “Wait for dial tone before dialing” boxStep 8. S elect ADVANCED in the same window Continue to next page

Page 8 - Establishing Your; To enter the “x3” in Windows 2000:; Select START

Step 9. In the Extra Settings box type x3 Step 10. Click OK to exit Advanced Connection Settings screen Step 11. Click OK to exit Modem Properties screen Step 12. C lick Close to exit Modems Properties screen Step 13. Close Control Panel Step 14. Reboot your computer and proceed to Establishing Your...

Page 9 - Double click; PHONE AND MODEM OPTIONS; Click MODEMS; Click; ADVANCED

Step 4. Double click PHONE AND MODEM OPTIONS icon Step 5. Click MODEMS tab Step 6. C lick PROPERTIES Step 7. In the General Tab, Uncheck – Wait for dial tone before dialing Step 8. Click the ADVANCED tab Continue to next page

Page 10 - Establishing Your Connection; do not

Step 9. In the Extra Initialization commands box type x3 Step 10. Click OK to enter the x3 into the Windows default settings Step 11. Click OK to exit Phone and Modem Options screen Step 12. Close Control Panel Step 13. Reboot your computer and proceed to Establishing Your Connection (Rebooting your...

Page 11 - Do not hang up the telephone

Step 3. If the phone has a volume control, ensure that the volumeis set to mid-range. Do this by lifting the handset to your ear andadjust the volume control to mid-range. Step 4. Return the telephone handset in the cradle. Step 5. Using your computer, begin the dial up or connection process as norm...

Page 13 - Double click the; MY COMPUTER; icon located on your; Control Panel; Continue to next page

Step 4. Write down the telephone number that appears (w/ area code) Locating a Host Modem PhoneNumber (Windows 2000) Step 1. Double click the MY COMPUTER icon located on your desktop Step 2. Double click Control Panel Continue to next page

Page 15 - Level Switch Settings Table; Telephone Telephone

Level Switch Settings Table The Data Port Anywhere Level switch adjusts the transmit level of yourmodem to the telephone set. The Level switch is manually set in oneof four settings and is dependent on the telephone set you’re using. Level 3 - Approximately 75% of the electronic or digital PBX telep...

Page 19 - Operating Tips and Troubleshooting; Telephone Set Volume Control -

Operating Tips and Troubleshooting A. USB Drivers - The DPA uses standard Microsoft drivers. When installing the DPA for the first time, you will be prompted by thecomputer to install/load drivers. Follow the prompts to identify the DPAto your operating system. B. Telephone Handset - The handset mus...

Page 20 - N. System Requirements

G. Princess and Trimline telephones - DPA will not operate with "Princess" or "Trimline" telephones, which have the keypad in thehandset. The electronics with which the DPA interacts are notaccessible in these telephones. H. Tone dialing - Make sure your modem is configured for Tone ...

Page 21 - O. Contacting Technical Support –; Telephone manufacturer, model name or model number; FCC Requirements

O. Contacting Technical Support – 800-275-6354. If Tech Support is not available to take your call, please leave a voice mail messageincluding your name, the telephone number you would like us to call,and a brief description of the problem you’re encountering. You canalso send questions and comments...

Page 23 - First Edition. Copyright

telecommunications company cause to request the user to disconnect theequipment. User's should ensure for their own protection that electrical ground connectionsof the power utility, telephone lines and internal metallic water pipe system, ifpresent, are connected together. This precaution may be pa...

Cortelco network adaptor - Manual

Table of Contents:

Summary

Other Cortelco Models