Cornelius WCC700 - Manual
Cornelius WCC700 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – SECTION; W–W
- Page 4 – FIGURE 2. DISPENSER ASSEMBLY; SEE VIEW ”X”; VIEW X
- Page 5 – FIGURE 3a. CLOSED POSITION
E
IMI Cornelius Inc; 2001
Revision A
620919550
November 30, 2001
IMI CORNELIUS INC.
One Cornelius Place
Anoka. MN 55303-6234
Telephone (800) 238–3600
Facsimile (763) 422–3246
DUAL DF/ED 2XX LID KIT FOR THE FOLLOWING ICE
MAKERS: Cornelius Extreme 522 and Wilshire WCC 700
Dispenser
DF/ED 2XX
Kit Number
629087947
Components
Qty
1. Cover
620043547
2
2. Lid Assembly (XAC 522 Icemaker)
620046064
1
3. Lid Assembly (WCC 700 Icemaker)
620046060
1
4. Mounting Bracket
22127
4
5. Screw, #8 SM
70217
20
6. RTV
50904
1
7. Label
91957
2
8. Instructions
620919550
1
9. Nut, Nylon
620701902
4
10. Washer, Nylon
620701903
4
11. Washer, Sealing
620701901
4
12. Ice Baffle
620037003
2
13. Gasket Strip
620505802
2
14. Binstat Kit
631500109
1
15. Plate, Top Cover
620044644
1
1. Unpack kit. Refer to Figures 1 & 2 for component detail.
2. Attach the ice baffles (item 12) to the lid assemblies (items 2 & 3) using the gasket strips, washers and acorn
nuts provided (figure 1).
3. Replace the center–mounting bracket supplied with the dual merchandiser kit with the top cover plate sup-
plied with this kit (item 15). Failure to do this will prevent the adapter kit from functioning properly.
4. Set the lid assembly onto the dispenser. Using the slotted holes on the side of the lid as a template, drill four
(4) 9/64” diameter holes at the bottom of the slots (Figure 2).
Note: Use extreme care not to drill into the hopper. Use a drill stop to ensure that the drill bit does not
penetrate deeper than
¼
” past the sheet metal. Failure to do so could result in a hole in the hopper, great-
ly reducing the efficiency of both the dispenser and ice maker.
5. Fasten the lid to the dispenser with four (4) #8 sheet metal screws (item 5), two on each side.
6. Seal the ice maker to the top of the dispenser as follows:
A.
Run beads of RTV (item 7) around the opening in the lid assembly and the inside of the perimeter of the
ice maker outline so that the ice maker will set on the RTV. Make sure that some RTV is applied inside
the nutserts on the lid assembly.
B.
Set the ice maker onto the lid and position it as required.
C.
Insert the thumbscrews (item 5) into the lid to attach the icemaker to the lid (Figure 3).
D.
Wipe away the excess RTV.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
E IMI Cornelius Inc; 2001 Revision A 620919550 November 30, 2001 9 10 11 13 12 2X 4X 4X 4X 2X FIGURE 1. PARTS SECTION W–W SCALE 0.625 9 11 13 12 10
E IMI Cornelius Inc; 2001 Revision A 620919550 November 30, 2001 FIGURE 2. DISPENSER ASSEMBLY WCC700 ICEMAKER 4 5 4X 16X SEAL ICEMAKER(S) TOITEM 2 AND 3 WITHITEM 6 (RTV) 5 4X 2 3 1 7 2X 2X SEE FIGURE(S) 3a & 3b SEE VIEW ”X” REPLACE ITEM 5–ED2XX DUAL–LIGHTED MERCHANDISER KIT WITH P/N 620044644 EX...
E IMI Cornelius Inc; 2001 Revision A 620919550 November 30, 2001 FIGURE 3a. CLOSED POSITION SCALE 0.250 1 WCC700 ICEMAKER LID ASSEMBLY EXTREME 522 ICEMAKER FIGURE 3b. OPEN POSITION SCALE 0.250 1 WCC700 ICEMAKER LID ASSEMBLY EXTREME 522 ICEMAKER
