Cornelius EJ1 - Manual - manualsarea.com

Page 2 - Training Manual

Jet Spray (Cold) Training Manual Jet Spray (Cold) Training Manual The products, technical information, and instructions contained in this manual are subjectto change without notice. These instructions are not intended to cover all details or varia-tions of the equipment, nor to provide for every pos...

Page 3 - TABLE OF CONTENTS

Jet Spray (Cold) Training Manual TABLE OF CONTENTS INTRODUCTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 Preview Questions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1Key Things To Know / Do - - - - -...

Page 5 - INTRODUCTION; E O

Jet Spray (Cold) Training Manual © 2000, IMI Cornelius Inc. - 1 - INTRODUCTION 1. P REVIEW Q UESTIONS Check your current knowledge by taking a few minutes to answer the following questions: 1. The 5 and 3-gallon bowl assemblies are interchangeable on certain models? _____ True _____ False 2. Parts t...

Page 6 - DUCTION

Jet Spray (Cold) Training Manual - 2 - © 2000, IMI Cornelius Inc. 2. K EY T HINGS T O K NOW / D O ✔ Work Safely! Always unplug/disconnect the power to the dispenser before servicing, and get help lifting the unit if it must be removed from the counter ! ✔ Make certain that you have adequate airflow ...

Page 7 - Product Description; IN

Jet Spray (Cold) Training Manual © 2000, IMI Cornelius Inc. - 3 - 3. O VERVIEW 3.1 Product Description Product Types The visual cold drink dispenser can dispense a premixed drink from the follow beverage selections: • Powder based (sport drinks and Icsotonic) • Syrup based product (non-carbonated) •...

Page 10 - SYSTEM DETAILS

Jet Spray (Cold) Training Manual - 6 - © 2000, IMI Cornelius Inc. SYSTEM DETAILS 1. W ATER 1.1 Water Quality Water quality has an affect on juice dispensing systems. • odor • taste • clarity/foaming Water filtration is recommended to assure the best beverage taste. 2. M ECHANICAL 2.1 Pump Assembly /...

Page 11 - Whipper Conversion; SYS

Jet Spray (Cold) Training Manual © 2000, IMI Cornelius Inc. - 7 - • Check whipper switch for adjustment. If moved too far forward, an air lock may occur, thereby breaking the magnetic lock between whipper motor and whipper chamber assembly. To adjust whipper switch, loosen screw to the right of the ...

Page 12 - Spray Verses Circulate

Jet Spray (Cold) Training Manual - 8 - © 2000, IMI Cornelius Inc. 2.4 Spray Verses Circulate Certain products are not suited for spraying, including products that have pulp and those that foam. Jet Spray units can be retro-fitted with circulator assemblies for pulpy or foamy products. • Circulator f...

Page 13 - Cooling Thermostat

Jet Spray (Cold) Training Manual © 2000, IMI Cornelius Inc. - 9 - 3. R EFRIGERATION 3.1 Cooling Thermostat There is one thermostat on all of the cold product units. This thermostat is located against the evaporator coil of the unit. On the JT20 and JT30 units the thermostat is mounted against the ri...

Page 14 - Refrigeration Charging

Jet Spray (Cold) Training Manual - 10 - © 2000, IMI Cornelius Inc. 3.8 Evaporators There are two types of evaporators on the Jet Spray cold products, coil and dome. It is important on both to remember to keep product above the top of the coils to insure proper cooling of the product and correct oper...

Page 15 - Spray Drive Motor Assembly

Jet Spray (Cold) Training Manual © 2000, IMI Cornelius Inc. - 11 - 4. C ONTROLS AND E LECTRICAL 4.1 Switches Separate spray and refrigeration switches are located on the front of each dis-penser, excluding the JS7, JW6, and JW5. There are separate switches for each side of multi-bowl models. These s...

Page 16 - TROUBLESHOOTING; Spray Drive Motor

Jet Spray (Cold) Training Manual - 12 - © 2000, IMI Cornelius Inc. TROUBLESHOOTING 1. N O S PRAY 1.1 Pump assembly Be sure the spray switch is ON Check impella magnet. Impella should spin freely. If it does not, remove and clean both impella and support pin. NOTE: Check that the Impella assembly is ...

Page 17 - Breaking Magnetic Lock; TROUBL

Jet Spray (Cold) Training Manual © 2000, IMI Cornelius Inc. - 13 - 2. N OISE IN P UMP A SSEMBLY 2.1 Impella Spacing Correct installation and maintenance of the impella is very important to efficient operation and the appearance of the product in the bowl. 2.2 Breaking Magnetic Lock The operation of ...

Page 18 - Condenser Cleaning

Jet Spray (Cold) Training Manual - 14 - © 2000, IMI Cornelius Inc. 4. B OWL L EAK NOTE: Do not confuse condensation drippings on the outside of the bowl as leaks. High humidity causes more condensation. 1. Be sure the gaskets are properly placed in the grooves on the bowl and that there are no tears...

Page 23 - ATTACHMENTS

Jet Spray (Cold) Training Manual © 2000, IMI Cornelius Inc. - 19 - ATTACHMENTS The following attachments should be included with this lesson: JetSpray Care And Cleaning Instructions TROUBL E SH OOTI N G

Page 25 - AT

Jet Spray (Cold) Training Manual © 2000, IMI Cornelius Inc. - 21 - REVIEW DATE: _______________________________________________ NAME: _______________________________________________ LOCATION: __________________________________________ The following questions summarize important points in this traini...

Cornelius EJ1 - Manual

Table of Contents:

Summary

Other Cornelius Models