Page 6 - WORLDWIDE REPRESENTATIVES
don’t hesitate to call us and benefit from I+ME’sextensive knowledge - your need is our desire. Our merger with the french corporation ACTIA in 1995allowed us to become a powerful supplier for theEuropean automotive industry. ACTIA products includediagnostic systems for automotive service andmainten...
Page 8 - Manual; NetPorty II; Contents
Manual NetPorty II Contents 1 Introduction ......................................... 1-1 1.1 Your I+ME NetPorty II ...................................... 1-2 1.2 System Requirements ...................................... 1-4 1.3 Delivery Contents ............................................. 1-5 1.3...
Page 11 - Introduction
1 Introduction Your I+ME NetPorty II. Overview,Systemrequirements, Delivery contents and s.o.
Page 13 - Troubleshooting; . If the problem persists, then feel free
Introduction Your I+ME NetPorty II Version 1.03 1-3 I+ME ACTIA is always eager to full fill the needs of ourcustomers. If problems should occur, please refer to Troubleshooting . If the problem persists, then feel free to contact our after-sales support hotline using thefollowing number: After-sales...
Page 14 - Requirements; standard PC with RS232 or Centronics (EPP 1.7 or
Introduction System Requirements Version 1.031-4 1.2 System Requirements PC requirements: • standard PC with RS232 or Centronics (EPP 1.7 or 1.9) interface • other device with standard RS232 interface (used signals described in chapter Hardware)
Page 15 - Support
Introduction Delivery Contents Version 1.03 1-5 1.3 Delivery Contents 1.3.1 Standard Your NetPorty II delivery package (Order code: IME 1602401) includes: • 1 NetPorty II • 1 System user manual (hardware/software) • Transfer tools to NetPorty II • LevelX software driver for design of 32 bit W indows...
Page 16 - Specifications; General Characteristics of NetPorty II
Introduction Technical Specifications Version 1.031-6 1.4 Technical Specifications General Characteristics of NetPorty II Processor 80C165, @36,84MHz Protocol Interface 1 x SJA1000, @ 16 MHz1 x 82527, @16MHz1 x UART Physical Interface CAN: according to ISO 11898(PCA 82C251) Memory 512 x 16 KByte RAM...
Page 17 - Options
Introduction Technical Specifications Version 1.03 1-7 Options Memory 64 KB EPROM instead of flash Physical interface: ISO Low Speed (ISO 11519) Diagnosis Channel ISO 9141 physical interface CAN CAN optional galvanicdisconnect Cable 1 m Cable for adaptation Power supply 230 V/AC to regulated 8 V/DC1...
Page 19 - Installation
2 Installation Installing your NetPorty II. Step by step installationprocedures for hardware and software.
Page 20 - Installing the Hardware
Installation Overview Version 1.032-2 2.1 Overview This chapter gives detailed information about installingthe NetPorty II hardware and about the necessary software drivers which make NetPorty II access possible. The NetPorty II is delivered with access driver and applications for W indows 95 and Wi...
Page 22 - the; If you start at serial port; is important; is important
Installation Installing the Software Version 1.032-4 2.3 Installing the Software 2.3.1 If you start at serial port Driver installation:1 Insert the CD. The setup programm will startautomatic, if not please start the program“START.EXE” in root path. 2 Go to "Software Installation" 3 Choose yo...
Page 23 - Problems; right driver
Installation Installing the Software Version 1.03 2-5 Problems : It is possible you chose an incorrect COM port. StartPcCANControl again and choose an other COM port. 2.3.2 If you start at parallel port 1 Make sure that your PC parallel port uses the EPP- mode . You have to control it under BIOS set...
Page 24 - Connect your; Info
Installation Installing the Software Version 1.032-6 This software is a W in32-Console-Application and runsunder Win95 and WinNT. Usage:- Connect your NetPorty II with one serial port. - If you do not use COM1 please change it into the fileL.BAT. - Start L.BAT. - If you get error messages like"B...
Page 25 - Hardware
3 Hardware The technical components, there specifications and theway they work together.
Page 26 - controller
Hardware Micro controller Version 1.033-2 3.1 Micro controller The I+ME NetPorty II includes the 16-bit Siemens 80C165 micro controller on a piggy back. Thecontroller’s clock frequency is 36,84MHz. The following recourses are used: Port 2.14 [EX6IN] SJA1000 Port 2.15 [EX7IN] 82527 / 16CS550 CS0-CS1 ...
Page 27 - The; NetPorty II internal buffers:
Hardware Memory Version 1.03 3-3 3.2 Memory The I+ME NetPorty II is equipped with Flash (CS0) 128 KByte (x 8 bit) SRAM (CS1) 512 KByte (x 16 bit) Optional it can be equipped withFlash 512 KByte (x 8 bit) and RAM 128 Kbyte (x 16 bit) 3.2.1 NetPorty II internal buffers: To avoid lost data (CAN is fast...
Page 28 - Interface
Hardware Protocol Interface Version 1.033-4 3.3 Protocol Interface The product has two CAN protocol chips at a frequencyof 16 MHz. The SJA1000 chip is connected to the 9 pinD-SUB connector with the CiA pinning. The optional82527 is also connected to the 9 pin D-Sub connectorwithout physical line dri...
Page 29 - interface; State of LED during download firmware:
Hardware Physical Interface Version 1.03 3-5 3.4 Physical Interface NetPorty II has the transceiver chip 82C251 (according to ISO 11898) as physical interface. It is not galvanicdisconnect. The standard physical interface is linked tothe SJA1000, the Output Control Register must be setto 0xFA. To co...
Page 30 - CAN Channel; Pins 1, 4 and 8 are not used by
Hardware Connector Version 1.033-6 3.6 Connector 3.6.1 9pol sub-min-D male 3.6.1.1 1 CAN Channel The CAN connector is based on the CiA standard if onlyone CAN channel is used. It is a 9pol sub-min-D maleconnector. Figure 3-1 Standard CAN Connector Pins 1, 4 and 8 are not used by NetPorty II
Page 31 - Pin
Hardware Connector Version 1.03 3-7 Pin Signal Description 1 nc not connected 2 CAN_L CAN_L bus line (dominant low) 3 CAN_GND CAN ground(connected on the cable shield) 4 nc not connected 5 CAN_SHIELD CAN ground(connected on the cable shield) 6 POW ER_GND power supply input ground 7 CAN_H CAN_H bus l...
Page 32 - More than 1 CAN Channel
Hardware Connector Version 1.033-8 3.6.1.2 More than 1 CAN Channel The pinning is different if more than one CAN channel isused. Figure 3-2 Pinning for more than 1 CAN channel
Page 33 - Connected to Port 6.7
Hardware Connector Version 1.03 3-9 Pin Signal Description 1 Uni_Out2 Connected to Port 6.7 2 CAN_L CAN_L bus line (dominant low) 3 CAN_GND CAN ground(connected on the cable shield) 4 Uni_Out0 Connected to Port 6.5 or UARTRx or CAN2 RX 0 5 CAN_SHIELD CAN ground(connected on the cable shield) 6 POW E...
Page 34 - To connect the; Connector definition:
Hardware Connector Version 1.033-10 3.6.2 25pol sub-min-D male To connect the NetPorty II with the PC it is possible to use the Centronics (LPT) port directly or to use the adapter cable touse the RS232 (COM) port. In both cases the pinning of the25pol sub-min-D male is the same. Connector definitio...
Page 35 - Cable set for serial connection
Hardware Connector Version 1.03 3-11 3.6.3 Cable set for serial connection Cable length: 30cm 25 pin female 9 pin female Signal 23 1 CD 20 2 Rx 19 3 Tx 16 4 DTR 18 5 GND 24 6 DSR 21 7 RTS 22 8 CTS 25 9 RI
Page 36 - Supply; Figure 3-3 Power Connector for NetPorty II
Hardware Connector Version 1.033-12 3.6.4 Power Supply The NetPorty II can be powered by an external power supply Therefore the connector is specified for thepower supply jack below: The power connector is a DC3.5/1.3 mm type. Thatmeans the internal diameter is 1.3mm. Figure 3-3 Power Connector for ...
Page 37 - Troubleshooting
4 Troubleshooting & Techn. Support Common problems and how to solve them. How to getin touch with our after-sales support experts if you sodesire.
Page 38 - What to do if you have problems; First and foremost, please read; very closely
Troubleshooting &Techn. Support What to do if you have problems Version 1.034-2 4.1 What to do if you have problems First and foremost, please read Installation very closely and make sure that you performed your installationexactly as described. For developers: The Key is often used in developin...
Page 39 - higher baudrates
Troubleshooting & Techn. Support What to do if you have problems Version 1.03 4-3 4.1.1 Solutions for all parts ... The system crashes after choose the hardware atPcCANControl: The selected memory area is not free, or theselected interrupt is being used by anotherapplication. Make sure that no c...
Page 40 - for
Troubleshooting &Techn. Support What to do if you have problems Version 1.034-4 4.1.2 Solutions for PCMCIA The system crashes after the installation of the Keyclient: The selected memory area is not free, or theselected interrupt is being used by anotherapplication. Refer to Installation. The sy...
Page 41 - Non-Supported PCMCIA Drives; PCMCIA Key
Troubleshooting & Techn. Support What to do if you have problems Version 1.03 4-5 The Key is inserted and PcCANControl starts withthe message: I+ME CARD not available or drive notready. Some aspect of the resource allocation is wrong.Refer to Installation for more information. 1.1.1 Non-Supporte...
Page 42 - Solutions for NetPorty II; Connect your NetPorty II with one serial port.
Troubleshooting &Techn. Support What to do if you have problems Version 1.034-6 4.1.3 Solutions for NetPorty II You start PcCANControl but the connection doesn’twork correct: For parallel port usage it is necessary to have theEPP-loader-firmware (BOOTLOAD.H86) in theNetPorty II -Flash-EPROM. All...
Page 43 - The NetPorty II doesn’t work under parallel port:
Troubleshooting & Techn. Support What to do if you have problems Version 1.03 4-7 The NetPorty II doesn’t work under parallel port: Use the right EPP mode on BIOS. It can be onlyone of the EPP modes work with one Win-Systemtogether. In past we find out that EPP 1.7 isnecessary for Win9x and EPP ...
Page 44 - and
Troubleshooting &Techn. Support What to do if you have problems Version 1.034-8 If you encounter difficulties which are not discussed inthe manual, or if you need more help than is offered in Installation and Troubleshooting , please call our after-sales service. Our experts will do their best t...
Page 45 - Glossary
Page 46 - Glossary
Glossary 5-2 Glossary Adapter A piece of hardware whichcontains one or more PCMCIAsockets.The Adapter containsthe interface between theSocket Controller and the HostSystem. AUTOEXEC.BAT A set of commands in the formof a batch file program that areautomatically executed by DOSto help configure your s...
Page 49 - Literature
Page 50 - Literature
Literature 6-2 Literature [1] SAB 80C167CR User ManualSiemens AG. [2] SAB C167CR Description of theOn-chip CAN-ModuleSiemens AG. [3] CiA DS 102-1CAN in Automation e.V
