Page 3 - Product Features
Product Features The Compaq TFT8030 Flat Panel Display has an active matrix, thin-film transistor (TFT), liquid crystal display (LCD). The monitor features include the following: ■ Large 18.1-inch (45.9 cm) viewable area display. ■ 1280 × 1024 resolution, plus full-screen support for lower resolutio...
Page 4 - Information Files
■ Energy Saver feature for Energy Star compliance. ■ Security lock slot ■ AssetControl ■ Compliant with the following regulated specifications: ❏ EPA ENERGY STAR ❏ European Union CE Directives ❏ Swedish MPR II 1990 ❏ Swedish TCO '99 Information Files The CD-ROM included with this monitor contains tw...
Page 5 - Setting Up the Monitor
Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow these steps: This monitor has multiple connectors on the back panel that can be used to connect two computers simultaneously to the monitor. Be s...
Page 7 - Connecting the Video Signal Cables
After you turn on the monitor, install the Compaq LCD Display Assistant utility included on the CD-ROM. Use the on-screen instructions to adjust the picture quality of your monitor. To install this utility, follow the instructions on the “Configuring Your Compaq LCD Monitor” card located in the Prog...
Page 9 - Signal Connectors and Cables
The DVI-D connector on this monitor uses digital video information to provide higher speed for higher display resolution. The results are more precise video displays without manually adjusting screen display quality. Signal Cables Included: ■ VGA (Analog) to VGA Connector (15-pin) ■ DVI-D Cable (Dig...
Page 10 - Input Select Switch; Automatic Input Selection
Input Select Switch The Video Channel Select control is located at the left-hand side of the lower front bezel. To the left and right of the Select control are two indicators that display the video channel that is selected. The left indicator is for Channel 1 and the right indicator is for Channel 2...
Page 13 - Removing the Monitor Base
Removing the Monitor Base Before you can mount the monitor onto a swing arm or other mounting fixture, you must remove the monitor from the base. CAUTION: Before beginning to disassemble the monitor, be sure the monitor is turned off and the power and signal cables are both disconnected. To remove t...
Page 15 - Operating the Monitor
Page 16 - Front Panel Controls
Front Panel Controls No. Icon Control Function 1 1-2 Video Channel Select Button Selects the video signal for input to the monito when two computers are connected to the monitor at the same time 2 Menu button 1. Launches 1st and 2nd-level on-screen menus. 2. Activates Auto Adjust when the OSD menu i...
Page 17 - On-Screen Display Settings; Advanced OSD Menu Levels
On-Screen Display Settings The adjustments for screen settings are located in the On-Screen Display (OSD) and can be viewed in one of six available languages. The following table shows the menus and their functions at each level: Advanced OSD Menu Levels Menu Level 1 Menu Level 2 Menu Level 3 Menu L...
Page 22 - How to Adjust Settings
How to Adjust Settings 1. To launch the on-screen display menus: ❏ Display the Basic Menu on the monitor screen by selecting the Menu button on the monitor front panel. ❏ Display the Advanced Menu by selecting the Menu button on the monitor front panel to display the Basic Menu, use the Minus or Plu...
Page 23 - Special OSD Messages
2. Select an item from the Main Menu by scrolling down and highlighting it using the Minus (-) button 2 located on the monitor front panel. To reverse or back up, press the Plus (+) button 3 . 3. Highlight your choice and press the Menu button 1 again. 4. Adjust the second-level menu displays using ...
Page 27 - Display Resolutions; Factory Preset Display Modes
When adjusting the Clock and Clock Phase values, if the monitor images become distorted, continue adjusting the values until the distortion disappears. To restore the factory settings, select Yes from the Factory Reset menu in the on-screen display. Display Resolutions The display resolutions listed...
Page 28 - User Modes
Factory Preset Display Modes Pre- set Pixel Format Horz Freq (kHz) Horz Polarity Vert Frep (Hz) Vert Polarity Pixel Clk (MHz) Source 14 1152 x 900 61.80 +/- 65.96 +/- 92.978 SUN 15 1280 x 1024 63.98 + 60.02 + 108.00 VESA 16 1280 x 1024 79.98 + 75.02 + 135.00 VESA 17 1280 x 1024 91.15 + 85.02 + 157.5...
Page 29 - Protecting the Monitor
Energy Saver Feature When the monitor is in its normal operating mode, the monitor utilizes less than 60 watts of power and the Power LED is green. The monitor also supports a reduced power state. The reduced power state will be entered into if the monitor detects the absence of either the horizonta...
Page 31 - Cleaning the Monitor; Shipping the Monitor
Cleaning the Monitor To clean the monitor, follow these steps: 1. Turn off the monitor and the computer. 2. Dust the monitor by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean cloth dampened with isopropyl alcohol. CAUTION: Do not u...
Page 32 - Specifications; Compaq TFT8030 Flat Panel Monitor
Specifications Compaq TFT8030 Flat Panel Monitor Display Type 18 inches Flat panel, Active matrix-TFT LCD 45.9 cm Viewable Image Size 18 inch diagonal 45.9 cm Face Treatment 3H hardness coating with antiglare treatment Maximum Weight (Unpacked) 17.63 lbs. 8.0 kg (unpacked) Dimensions Height Depth Wi...
Page 34 - Agency Regulatory Notices; Modifications
Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resid...
Page 35 - Cables; Canadian Notice
Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. Operati...
Page 37 - EPA Energy Star Compliance; Why do we have environmentally labelled computers?
EPA Energy Star Compliance Monitors that are marked with the Energy Star Logo meet the requirements of the EPA Energy Star program. As an Energy Star Partner, Compaq Computer Corporation has determined that this product meets the Energy Star guidelines for energy efficiency. Specific details on usin...
Page 38 - What does labelling involve?
environmentally harmful substances are used both in the products and during their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment, most of these potentially damaging substances sooner or later enter nature. There are also other characteris...
Page 39 - Environmental requirements; Flame retardants
The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labelled products must meet stri...
Page 41 - Power Cord Set Requirements
Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO´99 requirement permits the inclusion of lead since no replacement has yet been developed. *Bioaccumulative is defined as su...
