Page 3 - Installation; Unpacking
1 Installation Unpacking Before unpacking the monitor, prepare a suitable workspace for your monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that monitor has enough space around it for sufficient airflow. Though the monitor uses very little power, some v...
Page 4 - Viewing Angle Adjustment
Installation Viewing Angle Adjustment The monitor is designed to allow users to have a comfortable viewing angle. The viewing angle can be adjusted as follows: Top (-5°~ +35°) & Left / Right (-45° to +45°). Figure 1-1 CAUTION: Do not force the monitor over its maximum viewing angle settings as s...
Page 5 - Detaching Monitor from Its Stand
Installation Detaching Monitor from Its Stand 1. Remove the rear panel 1 from the monitor. (see Fig. 1-2) 2. Remove the rear support panel 2 from the swivel base support column. 3. Unscrew screws 3 the swivel base support column 4 . Figure 1-2 Compaq 7020 Flat Panel Monitor User’s Guide 1-3
Page 6 - Connecting the Display to the Swivel Base
Installation Connecting the Display to the Swivel Base Before connecting the display to the swivel base support column, please refer to Fig.1-2. The rear of this display has four integrated 4 mm, 0.7 pitch, threaded holes, as well as four 5 mm access holes in the plastic covering as illustrated in F...
Page 7 - Cable Installation
Installation Cable Installation Please follow these instructions to install the cables. 1. Remove the back panel 1 from the rear of the monitor. (See Fig. 1-4). 2. Remove the rear support panel 2 from the swivel base support column. 3. Place the signal cable, the DC power cable and the audio cable i...
Page 8 - Connecting the Display to Your Computer
Installation Connecting the Display to Your Computer 1. Power off your computer. 2. Connect one end of the signal cable to the monitor's VGA port or DVI port (digital models only). (See Fig. 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. 4. Make sure both c...
Page 9 - Connecting the AC Power
Installation Connecting the AC Power 1. Connect the power cord to the AC adapter. (See Fig. 1-6) 2. Connect the AC adapter's DC output connector to the DC Power Jack of the monitor. 3. Connect the power cord to an AC power source. Figure 1-6 WARNING: We recommend to install a "Surge Protector...
Page 10 - Connecting the Audio Cable
Installation Connecting the Audio Cable The instructions in this section apply only to monitor models featuring speakers. 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's "AUDIO OUT" jack of your CD ROM drive. (See Fig. 1-7) 2. Conne...
Page 11 - Setting Up the Monitor; Power Management System
Installation Setting Up the Monitor 1. Make sure the AC Adapter is connected to the monitor. 2. Turn on the monitor's power switch, located on the bezel of the monitor. Power Management System The monitor supports one low power mode. When the monitor is in the low power mode, the monitor screen will...
Page 12 - Display Controls; User Controls
2 Display Controls User Controls The monitor features several function controls and indicators: Figure 2-1 1 *Stereo Speakers PC Audio Stereo output. 2 External Headphone Jack (speaker models only) The monitor speakers will be disabled when using an external headphone or external speakers. 3 Menu Bu...
Page 13 - Adjusting the Monitor’s Display; OSD Function Menu
Display Controls 5 DC Power-On Indicator LED lights Green color - Power is ON. LED lights Amber - Monitor is in “Power Saving Mode”. LED is off - Power is OFF. 6 DC Power Switch Press the power switch to switch the monitor ON/OFF. 7 *Speaker Volume Control Increase Volume - Turn the knob clockwise. ...
Page 14 - OSD Menu
Display Controls The firmware may have been updated to a later version. However, the version number shown on all OSD menus in this guide will remain Ver. 1.00. The following menus show the functions at each level: OSD Menu Main Menu Advanced Menu Menu Level 3 Brightness Adjustment Scale Contrast Adj...
Page 16 - How to Adjust Settings; Basic Main Menu; Advanced Main Menu
Display Controls How to Adjust Settings 1. To launch the on-screen display menu, complete the following: ❏ Basic Main Menu : To display the Basic Main Menu, press the Menu button on the monitor front panel. ❏ Advanced Main Menu : Select “Advanced Menu” from the Basic Main Menu to display the Advance...
Page 17 - Energy Saver Feature
Display Controls After the Advanced Main Menu has been selected, it remains the default on-screen display each time the monitor is powered on until the Basic Main Menu option is selected again. 2. To select an item from the Basic Main Menu, scroll down and highlight an item by pressing the Minus (-)...
Page 18 - Energy Saver Levels
Display Controls amber. When the monitor is in the reduced power state, the monitor will utilize less than 5 watts of power. There is a brief warm up period before the monitor will return to its normal operating mode. Refer to your computer manual for instructions on setting energy saver features (s...
Page 19 - Technical Information; Monitor Specifications
3 Technical Information Monitor Specifications Screen Size 17.0” (43 cm) Display Type Active matrix color TFT LCD Resolution 1280 x 1024 Display Dot 1280 x (RGB) x 1024 Display Area (mm) 337.92 x 207.34 (HxV) Lamp Voltage 720 Vrms (typical) Lamp Current 6.0 mA rms. (typical) Input Signal Analog RGB ...
Page 20 - Preset Display Modes
Technical Information Monitor Specifications Power Input Voltage Frequency 100 to 240V AC 50-60 Hz Environmental Considerations Operating temperature: 5°C to 40°C/41°F to 104°F Humidity: 20% to 80% (non-condensing) Storage temperature: -20°C to 60° C/-4°F to140° F Humidity: 5% to 85% (non-condensing...
Page 25 - Troubleshooting
4 Troubleshooting This monitor has been pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Note: This monit...
Page 26 - PROBLEM: There is no picture on the monitor.; PROBLEM: There is no picture on monitor.
Troubleshooting PROBLEM: There is no picture on the monitor. If there's no picture on the monitor, please perform the following steps: 1. Make sure the power indicator on the monitor is ON, all connections are secured, and the system is running on the correct timing. Refer to Chapter 3 for informati...
Page 27 - Agency Regulatory Notices; Federal Communications Commission Notice; Modifications
A Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a res...
Page 28 - Cables; Canadian Notice
Agency Regulatory Notices Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15...
Page 29 - European Union Notice; EPA Energy Star Compliance
Agency Regulatory Notices European Union Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European nor...
Page 30 - Power Cord Set Requirements
Agency Regulatory Notices Power Cord Set Requirements The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the monitor to operate on input voltages between 100-120V or 200-240V. The power cord set (flexible cord or wall plug) received with the monitor meets t...
Page 31 - Why do we have environmentally labelled computers?
B TCO ‘99 Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally a...
Page 32 - What does labelling involve?
TCO ‘99 There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity generation have a negative effect on the environment (e.g. acidic an...
Page 33 - Environmental Requirements; Flame retardants
TCO ‘99 Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): [email protected] Current information regarding TCO...
