Coleman 8200 Series - Manual
Coleman 8200 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Natural Gas Conversion Instructions
- Page 3 – Remove the screws holding the rear heat
- Page 4 – Remove the screws from the bottom of the heat
- Page 5 – Disconnect the right side flexline from the mani-; You are now ready to install
- Page 7 – Installing the NG regulator; Remove the hose from the brass flare fitting; Note: For the following steps, the supplied pipe; Remove the grommet in the side of the cart by
- Page 8 – Reinsert the grommet in the side of the; Note: Pay attention to arrow on the NG
- Page 9 – Converting the Rear Infrared Burner to NG
- Page 10 – Converting the Side Burner to NG; Remove side burner grate, porcelain cap and
- Page 11 – Remove the two screws holding the bezel and
- Page 12 – Install the NG valve assembly to the underside; Note: Make sure the NG valve is facing towards; Reattach the bezel to the front of the side burner; Note: Make sure the bezel is installed in the; Connect the end of the new gas supply hose to; This completes the side burner conversion.
- Page 13 – Label the Grill; Note: At the completion of the
- Page 14 – NOTES
Natural Gas Conversion Kit
IMPORTANT
Read this document carefully before attempting installation
of this conversion kit. These instructions should be left with
the consumer for future reference.
For the following Coleman® Gas Barbecue Grills:
8100 Series (M/N 9992-643)
8200 Series (M/N 9992-644)
WARNING
• This Natural Gas conversion Kit must be installed only by a qualified
service technician.
• Gas supply system must be installed in accordance with the U.S.
National Fuel Gas Code.
• This appliance and its individual shut off valve must be disconnected
from the gas supply piping system during any system pressure test in
excess of 1/2 PSI (3.5 KPA).
• Use a system manual shut off valve to shut off the gas supply to this
gas appliance before continuing with installation procedures.
WARNING
• If the information in this document is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss
of life. Read the Coleman®
Gas Barbecue Use, Care & Assembly
Manual With Grill Lighting Instructions, before attempting installation
of this conversion kit.
WARNING
• TURN OFF THE GAS SUPPLY!
DO NOT attempt to install this Natural Gas Conversion Kit
while the barbecue is in operation or is hot.
Installation and provision for combustion and ventilation air
must conform with the
National Fuel Gas Code, ANSI Z223.1,
or
CAN/CGA-B149.1, Natural Gas Installation Code, or
CAN/CGA-B149.2, Propane Installation Code.
WARNING
A liquid propane tank, not connected for use with this gas barbecue,
shall not be stored in the vicinity of this or any other appliance.
Note: These instructions apply to
more than one model grill. The
parts included are designed for
your specific grill. The
illustrations may differ slightly
from model to model.
Turn off LP tank and disconnect
regulator from tank prior to servicing grill.
Connections must comply with local requirements and are the sole responsibility of the person performing
the work. A certified plumber must make connection to gas source.
All codes must be followed.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Part No. Qty Description 1 1 Main Burner Valve & Manifold Assembly (NG) 8100 1 Main Burner Valve & Manifold Assembly (NG) 8200 2 1 Hose 19" - 3/8" Flare Both Ends for Side Burner (NG) 3 1 Side Burner Valve Assembly - 12K BTU (NG) 4 1 Regulator 3/8" FNPT Threads (NG) 5 1 Nipple Pi...
Tools Needed: Phillips head screwdriver1/4" nut driver *9/16" wrenchAdjustable wrench Fig 4 Fig 1 Fig 2 Fig 3 Rear Heat Shield Screws Heat Tents Screws * 1/4” socket set with extension can also be used. Natural Gas Conversion Instructions Be sure gas supply is off, the knobs are in the offpo...
Fig 5 Fig 6 Side Screws (Repeat on left side). Screws under lip Fig 8 Fig 7 Tabs Natural Gas Conversion Instructions 5. Remove the screws from the bottom of the heat shield, holding the front heat shield in place. Thescrews are located under the bottom lip of theshield (Fig. 5). 6. Remove the two si...
