Page 2 - Contents
2 DANGER • FOR OUTDOOR USE ONLY. NEVER operate grill in enclosed areas, as this could lead to gas accumulating from a leak, causing an explosion or a carbon monoxide buildup which could result in injury or death. DO NOT use in garages, breezeways, sheds or any enclosed area. (Fig. 1) • NOT FOR USE B...
Page 3 - Follow these safety rules before each use:; WARNING; General Installation
1 3 2 36" 8 7 36" (90cm) 36" (90cm) 36" (90cm) Clear REPRESENTATIVE ILLUSTRATION • Installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1 (USA), CAN/CGA-B149.1, Natural Gas Installation Code or CAN/CGA-B149.2,...
Page 4 - CAUTION; Electrical Attachments
4 Longer detachable power-supply cords or extension cords must be used with care. The marked electrical rating of the cord set or extension cord must be at least as great as the electrical rating of the appliance. If the appliance is of the grounded type, the exten- sion cord should be a grounding-t...
Page 5 - Cylinder Specifications; Hose and Regulator
5 DANGER • DO NOT insert any foreign objects into the valve outlet. You may damage the valve. A damaged valve can cause a leak, which could result in explosion, fire, severe per- sonal injury or death. WARNING • Cylinders must be stored outdoors out of the reach of children and must not be stored in...
Page 6 - Transporting the Cylinder
WARNING Handle a full cylinder with care. Gas is under high pressure. DANGER • NEVER store a spare L.P. gas supply cylinder under the grill body or inside grill enclosure or in the vicinity of any heat producing appliance. (Fig. 12) • NEVER fill the cylinder beyond 80% full. Failure to follow this i...
Page 8 - Step; Hardware shown actual size; . Fasten Casters tight against the Caster Brackets.
Ö Ö NOTE: Use a large piece of cardboard or a ground cloth to protect the painted finish on the grill. Ö Ö NOTE: The base pieces are assembled up-side- down in this step. Step 1 1-A Center Base Right Base Left Base (TN) M6 x 15mm Screw (8) Qty. Hardware shown actual size 1-B 1-B . Fasten Casters tig...
Page 9 - Carefully turn the assembly; Self Tapping Screw; Hardware shown actual size 2-B; . Assemble the Cylinder; Front
Ö Ö Carefully turn the assembly Right-Side-Up. Ö Ö Engage the LockingCasters to preventmovement during the restof the assembly process. Step 2 9 2-A 2-B 2-A . Assemble the Cylinder Retaining Bolt to theCylinder Support. (VP) Self Tapping Screw (1) Qty. Hardware shown actual size 2-B . Assemble the C...
Page 10 - . Assemble two Cart Spacers between; . View of Cart Spacers properly
Ö Ö Assemble two Cart Spacersto the Grill Cart. Step 4 10 4-A . Assemble two Cart Spacers between the Left and Right Panels using eightScrews (TN). Ö Ö NOTE: The Cart Spacers are identical. Assemble one vertically and one hori-zontally. Ö Ö Tighten all fasteners. Hardware shown actual size (TN) M6 x...
Page 11 - The Rear Panels; M6 Locking Hex Nut; . Assemble one Door Magnet to the Right Panel with two
Step 5 11 5-A . Assemble two Rear Panels to the cart assem-bly using eight Screws(TN). Ö Ö NOTE: The Rear Panels are identical. Ö Ö Align the squareholes on the RearPanel with thetabs and pushdown to installthe panels. Ö Ö Tighten allfasteners. Hardware shown actual size (TN) M6 x 15mm Screw (8) Qty...
Page 12 - A second person is; Do Not Pinch
7-A Grill Cart Firebox Ö Ö Assemble Firebox to theGrill Cart. Ö Ö NOTE: A second person is needed when aligning theFirebox to the Grill Cart. Step 7 7-A . Carefully place the Firebox onto the Cart Assembly. Do not damage the Electrical Wires (see Fig. 7-B and 7-C). The Electrical Wires must be route...
Page 13 - M6 Flat Washer; LOOSELY
Ö Ö Fasten the Firebox to theGrill Cart. NOTE: In Fig. 8-A and 8-B, the Cart Spacer is not illustrated. Step 8 13 8-A Hardware shown actual size (TN) M6 x 15mm Screw (4) Qty. (DY) M6 Flat Washer (4) Qty. Flange on Right Side Panel Flange on Firebox Firebox TN (x2) DY (x2) 8-B 8-A . Lower the Firebox...
Page 14 - You will tighten these screws
Ö Ö NOTE: The Grill Lids should be opened for Step 9. Ö Ö Assemble Right Side Table tothe Grill. Step 9 9-A 9-B 9-C 9-A . Raise the Grill Lids. Ö Ö Place the Right Side Table against theFirebox and on top of the Right RearPanel. Hardware shown actual size (TN) M6 x 15mm Screw (4) Qty. 9-B . LOOSELY ...
Page 15 - View of Grill from Rear; assemble two additional
15 Ö Ö Assemble Right Side Tableto the Grill (continued). Step 10 10-A 10-B View of Grill from Rear 10-C 10-D TN (x2) 10-A . LOOSELY assemble two additional Screws (TN) and two Flat Washers (DY)through the Firebox into the Right SideTable at the rear of the grill. 10-C . Assemble two additional Scre...
Page 16 - . Align three studs from Left Fryer; You will tighten this screw
Ö Ö NOTE: The Grill Lids must be opened for Step 11. Ö Ö Assemble Left FryerAssembly to the Grill. Step 11 11-A 11-B 11-C 11-A . Raise the Grill Lids. Ö Ö Place the Left Fryer Assembly againstthe Firebox and on top of the Left RearPanel. Hardware shown actual size (TN) M6 x 15mm Screw (1) Qty. 11-B ...
Page 18 - Fuel Hose from Fryer Assembly; . Retract the Collar on the; Male; “OFF”
Ö Ö Assemble the Fuel HoseFitting from the Grill to theFryer Assembly. Step 13 13-A Fuel Hose from Fryer Assembly 13-A . Assemble the Fuel Hose Fitting from the Grill to the Fryer Assembly. 13-B . Retract the Collar on the Quick Coupler before insert-ing the Male Hose Fitting. Ö Ö Fully insert the M...
Page 19 - . Attach the Electrode Wire to the Electrode Tip on the Side Fryer.
Ö Ö Assemble the ElectrodeWire to the Electrode Tipon the Side Fryer. Ö Ö Assemble the Grease Panbelow the Fryer Burner. Step 14 14-A 14-A . Attach the Electrode Wire to the Electrode Tip on the Side Fryer. Electrode Tip Route the Electrode Wire through the slot in the Fryer Panel. Left Side Panel 1...
Page 20 - . View showing the Fryer Heat Shield properly installed.
Ö Ö Assemble Front Fryer HeatShield. Step 15 15-A 15-A . Assemble Fryer Heat Shield. Ö Ö NOTE: Place the Fryer Heat Shield between the Fryer Panel and the Flexible Fuel Hose. Do not pinch Electrode Wire. Ö Ö Engage the two tabs on the Heat Shield downward into the rectangle holes. 15-B 15-B . View s...
Page 21 - . Route the Back Burner Electrical Wire through the Wire Support.
Ö Ö Route the Electrical Wiresunder the Right Side Table. Ö Ö Note the location of theElectrode Module. Step 16 16-A 16-B 16-C 16-A . Route the Back Burner Electrical Wire through the Wire Support. Electrical Wire Wire Support Electrode Module Back Burner Electrical Wire 16-D Wire Tie Electrical Wir...
Page 22 - Electrode Module; . Firmly push the Electrode Wires into the Electrode Module.
Ö Ö Assemble the electrodeWires and the Battery tothe Electrode Module. Step 17 17-A Electrode Module Igniter Button Wires (Note: Large Tabs) 9-Volt Battery T EST THE I GNITER : A SPARK SHOULD APPEAR ATELECTRODE TIP . I F THE SPARK DOES NOT APPEAR : -C HECK THE WIRE CONNECTIONS TO THEMODULE . -C HEC...
Page 23 - Route; Do not; . View showing Rear Trim Plate properly installed.
Ö Ö Fasten the Rear Trim Plateto the Grill Cart. (VP) Self Tapping Screw (2) Qty. Hardware shown actual size 18-A 18-A . Fasten the Rear TrimPlate to theFirebox withtwo Screws(VP). Ö Ö NOTE: Route ElectricalWire throughnotch. Do not pinch wire . Ö Ö Tighten allfasteners. FIREBOX VP (x2) REAR TRIM PL...
Page 24 - M5 x 15mm Flat Head Screw
19-A Hardware shown actual size (XR) M5 x 15mm Flat Head Screw (8) Qty. Ö Ö Fasten both Left and RightDoors to the Grill Cart. Ö Ö Attach the Tool Hook to theRight Door. 19-B . Fasten the Right Door to the Grill Cart with four Flat Head Screws (XR). Ö Ö NOTE: Right Door has Tool Hook Brackets. Left ...
Page 25 - M4 X 5mm Screw
20-A Ö Ö Fasten the Door Handlesto the Doors. Ö Ö Attach the Tool Hook to theRight Door. Ö Ö NOTE: M4 x 5mm Screws are factory installed into theHandles. Step 20 Hardware shown actual size (EZ) M4 X 5mm Screw (4) Qty. EZ (x2) DOOR HANDLE RIGHT DOOR 20-A . Fasten one Door Handle to the Right Door wit...
Page 28 - nsert Pointed Tip of the Spit Rod into the Motor.
Ö Ö Assemble the Motor MountBracket to the right outside ofthe Firebox. Ö Ö Assemble the Rotisserie tothe Firebox. Step 25 Hardware shown actual size (TN) M6 x 15mm Screw (2) Qty. (UO) M6 Locking Hex Nut (2) Qty. 25-A TN (x2) UO (x2) Motor Mount Bracket 25-C Handle Set Collar Fork Slip Collar Fork S...
Page 29 - . Remove Handle immediately after placing Rotisserie into
25-E Push Button to Remove Rotisserie Handle 25-E . Remove Handle immediately after placing Rotisserie into the Firebox. Damage will occur if the Handle is notremoved prior to cooking. CAUTION • DO NOT OPERATE THE GRILL WITH THE ROTISSERIE HANDLE ON THE SPIT ROD. 29
Page 30 - During assembly of
Ö Ö Attach an LP Cylinder to theGrill. 26-A Cylinder Support LP Cylinder 26-A . Set LP Cylinder in the Cylinder Support with the outlet valve facing toward the front of the grill. 26-B 26-B . Tighten the Cylinder Retainer Bolt against the bottom cylinder collar. Cylinder Retainer Bolt 26-C 26-C . In...
Page 31 - the factory to use LP GAS, skip back to Step 26.
Ö Ö NOTE: Step 27 applies to you only if your grill is set up from the factory to use NATURAL GAS. If your grill is set up from the factory to use LP GAS, skip back to Step 26. Step 27 P LACE THE RUBBER PLUG ONTO THE GAS SUPPLY LINE . T HEN ATTACH THE SOCKET END OF THE QUICK DISCONNECT COUPLINGONTO ...
Page 32 - Leak Testing; How to Check for Leaks; Fixing A Fuel Leak
1. Check that the cylinder valve is closed by turning the cylinder knob clockwise to a full stop. 2. Check that all the grill burner knobs are in the off position. 3. Remove the protective caps from the cylinder valve and cou - pling nut. NOTE: The coupling nut connects to the large outside threads ...
Page 33 - Lighting Instructions
CAUTION Inspect the gas supply hoses before each use. If there are cuts, damage, excessive abrasion or wear, replace the hosesprior to operating the appliance. During assembly of grill andwhen attaching or replacing the L. P. gas cylinder, insure thatall gas supply hoses are free of kinks and/or dam...
Page 34 - Lighting Rotisserie Burner; Igniter Lighting; Match Lighting; Fryer; Igniter Lighting
Lighting Main Burners CAUTION DO NOT touch hot grill parts with bare hands! You MUST use protective gloves. CAUTION Be certain the gas is shut off at the L.P. cylinder valve anytime the grill is not in use. 1. Turn all burner control knob(s) to off. 2. After burner flame goes out, turn off fuel supp...
Page 35 - Grilling Tips and Hints; General Use and Correct Burner Flames; Condition The Grill
Good Bad Yellow Blue Holes in Burner Yellow Blue 21 Grilling Tips and Hints Follow These Steps: 1. Shut off gas at the burner valve(s) and stay away! 2. Allow the fire to burn itself out. 3. Once the fire is out and the appliance has cooled, shut off the L.P. cylinder valve. 4. Clean all parts and i...
Page 36 - Steps For Cleaning Venturi:; Cleaning the Venturi; Side Fryer Cooking Methods; The Side Fryer Option allows for several addi-
Steps For Cleaning Venturi: 1. Remove burner from grill bottom. 2. Look inside lower end of venturi tubes for nests, webs or mud. 3. To remove the above obstructions, use an accessory flexible venturi brush or bend a small hook on one end of a 20-inch- long flexible wire such as the one shown in Fig...
Page 37 - Moving and Storage; DANGER; Orifices; REPRESENTATIVE ILLUSTRATION; Problem: Burner will not light or has incomplete; Cleaning and Maintenance; Suggested Cleaning Materials:
CAUTION A collision with the grill, as with any metal object, could cause injury. Use care when moving a portable gas grill. WARNING If the grill is not in use, the gas MUST be turned off at the fuel supply cylinder. Moving and Storage Troubleshooting DANGER NEVER attempt to operate your grill witho...
Page 38 - For Your Additional Safety; Troubleshooting
TYPE 1 CONNECTION ILLUSTRATION Thermal Sensitive Handwheel 1-5/16" Acme Connection Nipple with Excess Flow Valve Regulator For Your Additional Safety DANGER If a fire occurs at the cylinder valve, DO NOT attempt to move the cylinder. IMMEDIATELY call the fire department and clear the area. You c...
Page 39 - PRODUCT REGISTRA; Coleman; COMPLETE THE ATTACHED REGISTRATION CARD AND RETURN WITHIN 10; PROMOTE BETTER PRODUCTS:
Please do not send other correspondence to the address belo w. PRODUCT REGISTRA TION DEP AR TMENT PO BO X 2931 WICHIT A ,KS 67201 A TTN: DEPT 586 IMPORTANT! Coleman ¨ Grill Warranty Registration Card COMPLETE THE ATTACHED REGISTRATION CARD AND RETURN WITHIN 10 DAYS TO RECEIVE THESE IMPORTANT BENEFIT...
Page 40 - CONGRATULATIONS ON YOUR NEW COLEMAN
7) Side burner (if applies) 8) Steamer/Fryer/Warmer (if applies) 9) Side table design 10) Color of the grill (not including stainless steel) 11) Warming racks 12) Dependable igniter 13) Size of the grill (available cooking square inches) 14) Integrated storage cabinet 15) Price16) Rotisserie (if app...
Page 41 - Recipes; Spice-rubbed spareribs; Cooking time after marination: 10 minutes
41 Recipes Spice-rubbed spareribs Cooking time: 45 minutes to partial boil; 16-20 min-utes to grill 6 pounds baby back pork spareribswater to cover For the spice mixture:2 Tb brown sugar3 Tb paprika1 Tb chili powder1 tsp garlic powder2 tsp black pepper1 Tb Dijon mustard1 Tb salt1 cup bottled barbequ...
Page 42 - Asian-flavored eggplant; Cooking time after marination: 6-7 minutes
42 Recipes Asian-flavored eggplant Cooking time: 8-10 minutes 2 large eggplant, peeled and sliced into 1/2 inchrounds2 Tb olive oil For the sauce:1 tsp grated ginger3 cloves minced garlic4 green onions, sliced thin2 Tb soy sauce1 Tb hoisin sauce2 tsp sugarjuice of one lime2 Tb sesame oil Heat the le...
Page 43 - Lamb grilled with rosemary and Dijon; Cooking time after marination: 30-40 minutes
Recipes 43 Lamb grilled with rosemary and Dijon Cooking time after marination: 30-40 minutes 2 pound boneless lamb leg, trimmed and butterflied8 cloves garlic, minced2 tsp fresh rosemary leaves, minced1/2 tsp dried thymejuice of one lemon1 Tb olive oilsalt and black pepper2 Tb Dijon mustard1 Tb wate...
Page 44 - Coleman Gas Barbecue Grill Limited Warranty; Warranty
The Coleman Co., Inc. • 3600 N. Hydraulic • Wichita, KS 67219 U.S.A. 1-800-835-3278 • TDD: 316-832-8707 9990-050 (11/24/03) ©2003 The Coleman Company, Inc. All rights reserved. Coleman ® is a registered trademark of The Coleman Company, Inc. Coleman Gas Barbecue Grill Limited Warranty Castings and B...
