Cognex 821 0038 1R - User Manual

Precautions To reduce the risk of injury or equipment damage, observe the following precautions when you install the Cognex product: l In-Sight 5000 series vision systems are intended to be supplied by a UL or NRTL listed power supply with a 24VDC output rated for at least 600 mA continuous and a ma...

Table of Contents Legal Notices 2 Regulations/Conformity 3 For European Community Users 5 Precautions 6 Table of Contents 7 Introduction 8 Support 8 Standard Components 8 Accessories 9 Cables 9 I/O Modules 11 Installation 13 Connectors and Indicators 13 Install the Lens 14 Connect the Ethernet Cable...

Introduction The In-Sight ® vision system is a compact, network-ready, stand-alone machine vision system used for automated inspection, measurement, identification and robot guidance applications on the factory floor. All models can be easily configured remotely over a network using an intuitive use...

Accessories You can purchase the following components separately. For a list of options and accessories, contact your local Cognex sales representative. Cables Note : Cables are sold separately. CAUTION : All cable connectors are keyed to fit the connectors on the vision system. Do not force the con...

Breakout Cable The Breakout cable provides connection to an external power supply, RS-232 serial communications, acquisition trigger input, high-speed outputs and encoder inputs (In-Sight 5604 only). The pin-outs for the cable are listed in the Breakout Cable Specifications on page 30 . This cable i...

Installation Read this section to learn how the vision system connects to its standard components and accessories. For a list of options and accessories, contact your Cognex sales representative. Note : l Cables are sold separately. l If a standard component is missing or damaged, immediately contac...

Note : l For the In-Sight 5100 and 5400 series, when the vision system is powered up, User 0 LED and User 1 LED both momentarily turn on. Then, User 0 LED turns off and User 1 LED stays on. Next, User 0 LED turns on and User 1 LED turns off. Finally, both LEDs momentarily turn on and then turn off. ...

Connect the Breakout Cable Note : You can clip unused wires short or use a tie made of non-conductive material to tie them back. Keep bare wires separated from the +24VDC wire. 1. Verify that the 24VDC power supply is unplugged and not receiving power. 2. Optionally, connect the I/O or serial wires ...

Specifications The following sections list general specifications for the In-Sight 5000 series vision systems. 5100, 5100C, 5400C, 5403 and 5400 Vision SystemSpecifications Specification 5100/5110 5100C 5400C 5403/5413 5400/5410 Minimum Firmware Requirement 1 In-Sight version 4.4.3 Job/Program Memor...

5604 Line Scan Vision System Specifications Specification 5604/5614 Minimum Firmware Requirement 1 In-Sight version 4.4.3 Job/Program Memory 128MB non-volatile flash memory; unlimited storage using a remote network device. Image Processing Memory 256MB SDRAM Sensor Type 1-inch CCD Sensor Properties ...

I/O Specifications Cable and connector specifications and connection examples for the acquisition trigger input, encoder inputs (In-Sight 5604 only) and the high-speed outputs are provided in the following sections. Acquisition Trigger Input The vision system features one acquisition trigger input, ...

Dimensional Drawings 5100, 5100C, 5400, 5400C and 5403 Vision System (With Lens Cover) Note : l Dimensions are in millimeters [inches] and are for reference purposes only. l All specifications are for reference purposes only and can change without notice. 32 Specifications

Cleaning/Maintenance Clean the Vision System Housing To clean the outside of the vision system housing, use a small amount of mild detergent cleaner or isopropyl alcohol on a cleaning cloth. Do not pour the cleaner on the vision system housing. CAUTION : Do not attempt to clean any DataMan product w...