Clifford AvantGuard 5.1 - Manual

3 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d what is included z Control module and harness z IntelliStart module and harness z Two five-button transmitters z Presentation envelope and quick reference card z Two window decal's z External antenna/receiver with ...

4 system maintenance The system requires no specific maintenance. Your transmitter is pow- ered by two miniature 3V lithium batteries that will last approximately one year under normal use. When the batteries weaken, operating range will be reduced and the system will provide a low battery warn- ing...

5 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d replacement remote controls You can purchase replacement remote controls from your Authorized Dealer or on-line at the following web site: www.directedstore.com Once you receive your new remote control, please refe...

6 transmitter configurations 1. LED Indicator 2. Arm/Disarm Button 3. Trunk Release Button 4. Remote Start Button 5. Silent Arm/Disarm Button 6. Clifford G5 Button nnoottee:: This manual describes the features and accessories that areincluded with your system along with information about compatibleC...

7 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d transmitter functions This system uses computer-based code learning to learn the transmit-ter buttons. This makes it possible to assign any transmitter button toany system function. The transmitter initially comes ...

9 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d using your system The buttons used in the instructions in this manual correspond to the standard transmitter configuration. If your transmitter has been custom configured, the icons on your transmitter buttons may ...

10 ally armed at that point. The system arms and the doors lock (if con- nected and programmed for passive locking) at 30 seconds, but the siren will not chirp. The early chirps provide you with a 25-second warning prior to arming. When armed, your vehicle is protected as follows: z The LED will fla...

11 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d Silencing section of this guide.) However, if the alarm completes the full trigger cycle when disarmed you will hear three chirps. disarming without a transmitter This feature allows you to disarm the system witho...

12 transmitter chirp muting To temporarily turn off the arm or disarm chirps, use transmitter chirp muting. Simply press on the transmitter, and the confirmation chirp(s) will be eliminated for that one operation only. The parking lights will flash to confirm the arm/disarm command. If you want the ...

13 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d intellistart and smartwindows sensor bypass When the system sees a command to start the vehicle via the Intellistart, it bypasses all sensors and will continue to bypass these sen- sors until the remote start shut...

15 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d transmitter valet mode To enter or exit Valet Mode, press twice and then . The LED status indicator will light solid when Valet Mode is entered, or will turn off when Valet Mode is exited. one-time auto-arming byp...

16 multiple event total recall This will report the last eight system triggers. 1. Press and hold of the PlainView 2 Valet switch. 2. While still holding , arm and disarm the system, then release the button. 3. The LED will start to blink to indicate the most recent triggerand proceed down to the ei...

17 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d Doors are covered by FACT II differently; if the alarm is triggered by an open door for three full cycles, the doors will be bypassed until the trig- ger ceases. FACT II is programmable. See the Programming Option...

18 diagnostics The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it. It detects any faulty switches and sensors and prevents them from dis- abling the entire system. The microprocessor will also record and report an...

19 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d disarming diagnostics Extra disarm chirps are the Tamper Alert. If three chirps are heard when disarming, the system was triggered in your absence. If three chirps are heard, the LED status indicator will indicate...

20 table of zones The zone number is the number of LED flashes used by the system to identify a specific input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. If the Warning Zone response is triggered, the LED w...

21 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d high frequency Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will store its current state t...

22 z Power Saver when the system is armed: After the system hasbeen armed for 48 hours, the LED will flash at half its nor-mal rate, decreasing the system's current draw. z Power Saver in Valet Mode: When the system enters ValetMode the LED illuminates steadily. If the vehicle is not used(ignition i...

23 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d manual programming instructions Be sure to document changes by taking note of all feature changes made in programming mode. To enter the User Selectable Features programming: 1. Ignition on - Turn the ignition to ...

24 number. 7. Exit programming - To exit programming mode turn the igni-tion off or wait 60 seconds without pressing the PlainView 2Valet switch. The siren will chirp three times to indicate pro-gramming mode has been exited. user selectable features * This feature is only available with IntelliStar...

25 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d user selectable features descriptions - column one add new remote (auto learn) Auto-learn new five-button remote controls to the system in the stan- dard button configuration. Once you have entered the feature, pr...

27 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d user selectable features descriptions - column two set pin code This feature allows the setting of the user's personal PIN code. For more information, please refer to the PIN Programming section of this guide. sel...

29 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d user selectable features descriptions - column three The features in this column pertain to programming individual trans- mitter channels in custom configurations. Following is an explanation of the features. arm/...

31 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d pin programming A PIN code can have one to four digits; each digit can be from 0-9. Programming Procedure 1. Enter the feature location in the installer programming grid. 2. Immediately press and release of the Pl...

32 PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set. 1. Turn on the ignition. 2. Enter the new PIN code. 3. Press and hold for three seconds. z LED turns on: New PIN code is learned and program-ming is comple...

34 Don'ts z DON'T remote start your vehicle or engage Shortstop or Autostartmodes in an enclosed area such as a garage or car port. z DON'T allow children access to your remote control. z DON'T engage remote start or Shortstop or Autostart modeswhen children or pets are present in the vehicle. z DON...

35 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d z Enter the vehicle without stepping on the brake or movingthe shift lever. z Insert your key into the ignition and turn to the run position. z Step on the brake, the remote start will turn off and theengine will ...

37 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d diesel compatibility The system will activate the engine’s glow plugs for the necessary dura- tion before starting via either a timer delay or through a direct connection to your vehicle’s glow plug indicator (may...

38 one-time valet feature This feature allows the system to be put in valet mode only until the next time the ignition is turned on. ON: Valet mode will be exited every time the ignition is turned on. OFF: Valet mode will only be exited by using the valet switch or the remote control. blackjax featu...

39 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d When BlackJax is programmed ON, BlackJax sequence will begin every time the ignition is turned on and must be turned off by entering your PIN code. It will then activate again while driving when triggered. blackja...

40 4. Siren chirps 1 time as confirmation of BlackJax bypassed. 5. Turn Ignition Off, siren chirps 3 times as confirmation of exit-ing programming. To return to normal BlackJax Operation 1. Turn ignition on. 2. Enter Pin code. 3. Within 10 seconds press . 4. Siren chirps 2 times as confirmation of B...

41 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d sensor description section 507M tilt sensor This sensor detects when the vehicle is being raised in an attempt to either remove the wheels/tires or tow the vehicle. This sensor is capa- ble of learning the vehicle...

43 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d 6. Press of the remote control to return to Primary zone adjustment and lock in Warn Away zone setting. z Siren chirps 2 times. z Primary zone can now be re-adjusted as described instep 3. z Or press again to lock...

46 glossary of terms 507M Tilt sensor: This sensor detects when the vehicle is being raised in an attempt to either remove the wheels/tires or tow the vehicle. This sensor is capable of learning the vehicle’s initial inclination angles each time the vehicle is parked. Control Unit: The "brain...

48 security & convenience expansions Here we have listed only some of the many expansion options avail- able. Please contact your dealer for a complete list of all the options available to you. Backup Battery: The 520T keeps the system armed, triggers the alarm and keeps the immobilization circu...

49 © 2 0 0 6 d i r e c t e d e l e c t r o n i c s — a l l r i g h t s r e s e r v e d health check Directed Electronics recommends you return to your installing Clifford deal- er to have your system checked for correct operation. The first check is due one year after the installation date and at ye...

Vista, CA 92081 www.directed.com © 2006 Directed Electronics - All rights reserved G919640 11-06 The company behind this system is Directed Electronics. Since its inception, Directed Electronics has had one purpose, to provide consumers withthe finest vehicle security and car stereo products and acc...