Char-Broil 463440109 - Manual

WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Turn ...

6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. NOTE...

WARNING For Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in sides or back of grill. • Check burner flames regularly. • Use grill only in well-ventilated space. NEVE...

Burner Flame Check •Remove cooking grates and flame tamers. Light burners, rotate knobs from HIGH to LOW. You should see a smaller flame in LOW position than seen on HIGH. Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Su...

Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burnerassembly or if you have trouble igniting grill.1. Turn gas off at control knobs and LP cylinder. 2. Remove cooking grates and flame tamers. 3. Remove screws and carryover tubes from rear of burners. 4. Remo...

First Time Use Read your Assembly Manual and ensure the grill is put together properly. Remove all Point-of-Purchase advertising material from all grill surfaces before first use. We recommend operating your grill on its highest setting for 15-20 minutes prior to your first use. This aids in removin...

Outdoor grilling is really quite simple. You'll succeed with burgers, dogs, or steaks usually on your very first try. With experience, you will learn how to work with your grill, creating more imaginative meals all the time. This knowledge makes up the art of grilling. Before you start grilling, org...

USDA Recommended Safe Minimum Internal Temperatures Beef, Veal, Lamb, Steaks, & Roasts 145° F Fish 145° F Pork 160° F Beef, Veal, Lamb Ground 160° F Egg Dishes 160° F Turkey, Chicken & Duck Whole,Pieces & Ground 165° F Cooking on your new grill is a hands-on experience, and it is recomme...

Why Clean? We've all heard the saying, 'an ounce of prevention is worth a pound of cure.’ This is great advice when it comes to keeping your grill clean. Routine Care Periodic cleaning of this grill is necessary,as grill fires can occur when grease andfood debris collect in the bottom of the grill. ...

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated...

NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance fromthose on your particular grill model. However, the methood of assembly remains the same. PARTS LIST 15 Key Qty Description JJ 1 GREASE CUP KK 1 CLIP, F/ GREASE CUP LL 1 TANK EXCLUSION MM 2 LEG EXTENDER NN 1 WING...

PARTS DIAGRAM 16 A B B B C B D D D E F G H I J I J J J I I I J K L M N O P Q Q Q Q R S T U V W X Y Z AA BB CC DD EE GG HH II JJ KK LL MM NN OO PP FF Q Q

ASSEMBLY Place legs as shown . Left leg assembly has large holes on ends of legs. Hook tank exclusion wireinto right and left leg assemblies Qty: 4 1/4 -20x1-1/2" Machine Screw " Place bottom shelf with cut out hole for LP tank next to legs with axle holes. Attach to right and left leg assem...

ASSEMBLY Attach front panel to cart with #8-32x3/8" sheet metal screws. Qty: 6 #8-32X3/8” Sheet Metal Screw Front Panel Turn assembly upside down. Insert axle rod into wheel, legs and other Axle Attach with (1) 8mm flat washer and hitch pin. Axle Spacer, Spacer and wheel. Axle Rod "Cone"...

Stand cart upright.This step requires two people to lift and position grill head onto cart.Carefully lower the grill head onto the cart. Make sure the regulator hose is hanging outside the cart. Attach with 1/4 -20x1/2" machine screws . " Qty: 4 1/4 -20x1/2" Machine Screw " Grill Hea...

Qty: 4 7X15 Fiber Washer Qty: 4 1/4 -20x1/2" Machine Screw " Qty: 4 1/4 -20 Flange Nut " Hook side wall of shelf over support brackets on side of firebox (A). Inside firebox insert 7x15 fiber washers and 1/4 -20x1/2" machine screws as shown (B). Attach shelf with flange nuts on each ...

Hook side wall of sideburner shelf over support brackets on side of firebox (A). Inside firebox insert 7x15 fiber washers and 1/4 -20x1/2" machine screws as shown (B). Attach sideburner shelf with flange nuts on each side. (C). " Qty: 4 7x15 Fiber Washer Qty: 4 1/4 -20x1/2" Machine Screw...

Bu rne r Tub e Valv e Sideburner Ignitor Wire Burner Clip C Sideburner Control Knob D Qty: 1 Wing Nut Attach sideburner bezel and valve with #8-32x3/8" machine screws (A). Place sideburner into shelf. Make sure valve is inside sideburner tube. Attach sideburner with wing nut (B). Hook burner cli...

Place heat tents over burners by inserting tabs into slots in front of firebox. Opposite ends of heat tents rest on pins in back of firebox. Heat Tent Back of Firebox Pin Heat Tent Front of Fireb ox Place cooking grates onto grate rests. Insert ends of Swing Away pivot wire into holes in sides of gr...

13 14 LP tank is sold separately. Use only with an OPD (over-fill protection device) equipped LP tank. Fill and leak check before attaching to grill and regulator. Place LP tank into hole in bottom shelf with tank collar opening facing to side as shown. Finger tighten tank thumbscrew to hold LP tank...

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fire ...

Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also) Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill LP c...

Troubleshooting - Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when control knob turned to ; no noise can be heard from spark module. SECTION II No sparks appear at any electrodes when control knob turned to ; noise can be heard from spark module. SECTION III S...